• Author / Uploaded
• andresito0421

Citation preview

INDUSTRIAL ROTARY SCREW AIR COMPRESSOR 10B Series Open 25, 30, 40 HP Standard & 24KT

PARTS LIST Part Number 02250049--- 583 eSullair Corporation

AIR CARE SEMINAR TRAINING Sullair Air Care Seminars are 3---day courses that provide hands---on instruction in the proper operation, maintenance and service of Sullair equipment. Individual seminars on Industrial compressors and compressor electrical systems are presented at regular intervals throughout the year at a dedicated training facility at Sullair’s corporate headquarters in Michigan City, Indiana. Instruction includes discussion of the function and installation of Sullair service parts, troubleshooting of the most common problems, and actual equipment operation. The seminars are recommended for maintenance and service personnel. For detailed course outlines, schedule and cost information contact: Sullair Corporate Training Department 1---800---348---2722 or 219---879---5451 (ext. 1867) --- Or Write --Sullair Corporation 3700 E. Michigan Blvd. Michigan City, IN 46360 Attn: Service Training Department

TABLE OF CONTENTS Section 1

ILLUSTRATIONS AND PARTS LIST

PAGE 1 1 2 6 8

1.1 PROCEDURE FOR ORDERING PARTS

12

1.6 COMPRESSOR COOLING AND LUBRICATION SYSTEM --WATER--- COOLED (25 & 30HP)

14

1.7 COMPRESSOR COOLING AND LUBRICATION SYSTEM --WATER--- COOLED (40HP)

16 20 22 26 28 30

1.8 COMPRESSOR DISCHARGE SYSTEM

32 34

1.14 WATER--- COOLED AFTERCOOLING OPTION ( 40HP)

36 38 40

1.16 HEAVY DUTY FILTER OPTION

1.2 RECOMMENDED SPARE PARTS LIST 1.3 MOTOR, COMPRESSOR, FRAME AND PARTS 1.4 AIR INLET SYSTEM 1.5 COMPRESSOR COOLING AND LUBRICATION SYSTEM --AIR--- COOLED (25--- 40HP)

1.9 ELECTRICAL BOX 1.10 PNEUMATIC CONTROLS 1.11 INSTRUMENT PANEL --- OPEN AND ENCLOSURE OPTION 1.12 AIR--- COOLED AFTERCOOLING OPTION (25 AND 30HP) 1.13 WATER--- COOLED AFTERCOOLING OPTION (25 AND 30HP) 1.15 WATER--- COOLED AND AIR--- COOLED ENCLOSURE AND PARTS OPTION 1.17 OPTIONAL AIR TANK --- 120 AND 200 GALLON 1.18 DECAL GROUP

NOTES

Section 1

ILLUSTRATIONS AND PARTS LIST 1.1 PROCEDURE FOR ORDERING PARTS Parts should be ordered from the nearest Sullair Representative or the Representative from whom the compressor was purchased. If for any reason parts cannot be obtained in this manner, contact the factory directly at the address or phone numbers listed below. When ordering parts always indicate the Serial Number of the compressor. This can be obtained from the Bill of Lading for the compressor or from the Serial Number Plate located on the compressor.

SULLAIR CORPORATION

Subsidiary of Sundstrand Corporation 3700 East Michigan Boulevard Michigan City, Indiana 46360 Telephone: (219) 879-- 5451 See Toll -- free Number Below FAX: (219) 874-- 1273

SULLAIR CORPORATION

Parts Distribution Division and Service Department 1625 E. Second Street Michigan City, Indiana 46360 Telephone: 1-- 800-- 348-- 2722 or (219) 879-- 5451 FAX: (219) 874-- 1835 (Parts) FAX: (219) 874-- 1805 (Service) 1.2 RECOMMENDED SPARE PARTS LIST DESCRIPTION element for main fluid filter 250025---521 repair kit for separator element 250034---111 repair kit for separator element 250034---113 replacement element for air filter 410036 repair kit for pressure regulator 250017---280 repair kit for solenoid valve 250017---993 replacement coil for solenoid valve 250017---993 replacement gasket for flexible coupling 040033 replacement gasket for flexible coupling 250007---544 repair kit for return line strainer 241771 repair kit for thermal valve 250025---620 repair kit for air inlet valve 250025---654 seal kit for minimum pressure valve 241581 repair kit for blowdown valve 250025---655 repair kit for shaft seal repair kit for separator/trap 040847 replacement spring for check valve 049905 SRF 1/4000 fluid (5 gallons) 24KT fluid (5 gallons) Sullube 32 fluid (5 gallons)

KIT NUMBER 250025-- 525 (std. & 24KT) 250034-- 112 (std.) 250034-- 114 (24KT) 250034-- 114 (std. & 24KT) 042445 (std. & 24KT) 250019-- 453 (std. & 24KT) 250018-- 970 (std. & 24KT) 250018-- 971 (std. & 24KT) 040517 (std.) 250007-- 559 (24KT) 241772 (std. & 24KT) 250025-- 621 (std. & 24KT) 250019-- 451 (std. & 24KT) 250026-- 758 (std. & 24KT) 250031-- 772 (std. & 24KT) 001836-- 007 (std. & 24KT) 044374 (std. & 24KT) 250003-- 657 250019-- 662 (std.) 046850-- 001 (24KT) 250022-- 669

QUANTITY 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

1

Section 1

ILLUSTRATIONS AND PARTS LIST 1.3 MOTOR, COMPRESSOR, FRAME AND PARTS

2

Section 1

ILLUSTRATIONS AND PARTS LIST 1.3 MOTOR, COMPRESSOR, FRAME AND PARTS key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

description base, motor/compressor nameplate, serial number rivet, pop !@8” x !@2” washer, springlock --- regulating !@2” nut, hex !@2”---13 angle, compressor mounting (25,30HP) Sangle, compressor mounting (40HP) capscrew, hex head gr5 !@2” x 1!@2”” capscrew, hex head gr5 #@8” x 1!@4” Scapscrew, hex head gr5 #@8” x 1#@4” capscrew, hex head gr5 #@8” x 2!@2” capscrew, hex head gr5 %@16” x 1#@4” coupling, hub (25, 30HP) S coupling, hub (40HP) element, drive coupling (25, 30HP) S element, drive coupling (40HP) hub, motor (25, 30HP) S hub, motor (40HP) washer, springlock --- regulating #@8” capscrew, hex head gr5 #@8” x 1!@4” plate, motor/compressor (40HP) adapter, motor (25, 30HP) Sadapter, motor (40HP) nut, hex #@8”---16 motor, 25HP S motor, 30HP S motor, 40HP shim set, motor nut, hex plated %@16” x 18” lug, Scrulug washer, springlock !@2” (25,30HP) Swasher, springlock regular %@8” capscrew, ferry head !@2”---13 x 1!@4” (25,30HP) Scapscrew, ferry head %@8” x 1!@2” (40HP)

standard part number

24KT part number

quantity

013569 040052 843102---050 837508---125 824208---448 250038---863 250004---580 828608---150 828606---125 828606---175 828606---250 828605---175 045673 250004---639 045672 250004---638 045671 250004---640 837506---094 828606---125 225980 250038---448 231977 824206---337 250029---985 250029---986 250029---987 020293 825305---283 849215---025 837508---125 837510---156

013569 040052 843102---050 837508---125 824208---448 250038---863 250004---580 828608---150 828606---125 828606---175 828606---250 828605---175 045673 250004---639 045672 250004---638 045671 250004---640 837506---094 828606---125 225980 250038---448 231977 824206---337 250029---985 250029---986 250029---987 020293 825305---283 849215---025 837508---125 837510---156

1 1 4 4 4 1 1 2 7 1 2 1 1 1 1 1 1 1 15 7 1 1 1 6 1 1 1 1 1 1 1 4

828408---125 828410---150

828408---125 828410---150

4 4

(Continued on Page 5) PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

3

Section 1

ILLUSTRATIONS AND PARTS LIST 1.3 MOTOR, COMPRESSOR, FRAME AND PARTS

4

Section 1

ILLUSTRATIONS AND PARTS LIST 1.3 MOTOR, COMPRESSOR, FRAME AND PARTS (Continued) key number 25 26 27 28 29 30

description

standard part number

24KT part number

quantity

compressor unit, 10B Series(I) adapter, SAE 5 grille, coupling guard (25,30HP) screw, ser washer %@16” x #@4” (25,30HP) washer, !@2” washer, #@8”

--250009---542 250038---863 829705---075 837208---112 838206---071

--250009---542 250038---863 829705---075 837208---112 838206---071

1 1 2 6 2 1

(I) There is an exchange program whereby a remanufactured compressor unit can be obtained from Sullair distributors or the factory at less cost than the owner could repair the unit. For information regarding the unit exchange program, contact your nearest Sullair representative or the Sullair Corporation. The shaft seal is not considered part of the compressor unit in regard to the 2 year warranty. The normal Sullair parts warranty applies. For shaft seal repairs, order shaft seal repair kit no. 001836---007.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

5

Section 1

ILLUSTRATIONS AND PARTS LIST 1.4 AIR INLET SYSTEM

6

Section 1

ILLUSTRATIONS AND PARTS LIST 1.4 AIR INLET SYSTEM key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

description air filter assembly (I) (includes Items 2, 3, 4, 5) nut, wing !@4”---20 hood, air filter element, air filter base, filter nipple, pipe !@8” x 3” coupling, pipe galvanized !@8” connector, tube start !@8”mnpt x !@4”t tubing, plastic !@4”od capscrew, hex gr5 %@8”---11 x 1!@4” washer, springlock %@8” valve, air inlet 2!@2” (II) connector, tube---el !@8”mpt x !@4”t o---ring, 3!@2” x !@8” elbow, pipe galvanized !@8” indicator, air filter maintenance washer, flat #@8”

standard part number

24KT part number

quantity

410036

410036

1

824815---004 043392 042445 017966 823102---030 803215---005 813604---125 250024---745 828610---125 837510---156 250025---654 813704---125 826502---238 801515---005 045757 838206---071

824815---004 043392 042445 017966 823102---030 803215---005 813604---125 250024---745 828610---125 837510---156 250025---654 813704---125 826502---238 801515---005 045757 838206---071

1 1 1 1 1 2 1 2!@2 ft 4 4 1 1 1 1 1 1

(I) For maintenance on air filter assembly no. 410036, order replacement element no. 042445. (II) For maintenance on air inlet valve no. 250025---654, order repair kit no. 250019---451.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

7

Section 1

ILLUSTRATIONS AND PARTS LIST 1.5 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- AIR-- COOLED (25-- 40HP)

8

Section 1

ILLUSTRATIONS AND PARTS LIST 1.5 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- AIR-- COOLED (25-- 40HP) key number 1 2 3

4

5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

description elbow, 90_ #@4” x #@4” (25, 30HP) S elbow, 90_ #@4” x #@4” (40HP) elbow, tube---m #@8” x !@2” (40HP) screw, hex head ser washer %@16” x #@4” (25, 30HP) Sscrew, hex head ser washer %@16” x #@4” (40HP) nut, hex ser washer plated %@16”---18 (25, 30HP) Snut, hex ser washer plated %@16”---18 (40HP) brace, cooler/starter nut, hex locking plated %@16”---18 (25, 30HP) Snut, locking #@8”---16 (40HP) fan, cooling (25, 30HP) S fan, cooling (40HP) guard, fan hub, fan (25, 30HP) S hub, fan (40HP) capscrew, ferry %@16” x 1!@2” (25, 30HP) S capscrew, ferry #@8” x 1#@4” (40HP) elbow, 90_ reducing 1” x #@4”(25, 30HP) nipple, pipe 1!@4” x 6” nipple, close 1” (25, 30HP) elbow, 90_ reducing 1!@4 x #@4” tube, fluid stop elbow, 45_ pipe #@4” nipple, pipe #@4” x 2!@2” elbow, tube---m #@8” x #@8” (40HP) tubing, copper #@8” (40HP) nipple, close #@4” (25, 30HP) S nipple, close #@4” (40HP) connector, tube #@4” x #@4” (25, 30HP) Sconnector, tube #@4” x #@4” (40HP) tee, reducing #@4” x !@2” x #@4” (25, 30HP) Stee, reducing #@4” x !@2” x #@4” (40HP) nipple, close !@2”

standard part number

24KT part number

quantity

810512---075 810512---075 810506---050

810512---075 810512---075 810506---050

6 5 1

829705---075

829705---075

12

829705---075

829705---075

18

825305---283

825305---283

7

825305---283 250018---605

825305---283 250018---605

13 1

825505---166 825506---198 042492 249012 225962 023350 231981 828405---150 828406---175 801604---030 822120---060 822216---000 801605---030 232823 801415---030 822112---025 810506---038 840115---006 822212---000 822212---000 810212---075 810212---075 802203---023 802203---023 822208---000

825505---166 825506---198 042492 249012 225962 023350 231981 828405---150 828406---175 801604---030 822120---060 822216---000 801605---030 232823 801415---030 822112---025 810506---038 840115---006 822212---000 822212---000 810212---075 810212---075 802203---023 802203---023 822208---000

4 4 1 1 1 1 1 4 4 1 1 2 1 1 1 1 1 2 ft. 2 3 2 4 1 2 1

(continued on page 11)

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

9

Section 1

ILLUSTRATIONS AND PARTS LIST 1.5 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- AIR-- COOLED (25-- 40HP)

10

Section 1

ILLUSTRATIONS AND PARTS LIST 1.5 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- AIR-- COOLED (25-- 40HP) (Cont’d.) key number 24 25 26 27 28

29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

description valve, globe !@2” plug, pipe !@2” elbow, 90_ tube !@4” x !@8” filter, fluid (I) tube, cooler fluid cooler to sump (25, 30HP) Stube, cooler fluid cooler to sump (40HP) nipple, pipe #@4” x 9” (25, 30HP) S nipple, pipe #@4” x 13!@2” (40HP) bushing, hex 1!@4” x #@4” tee, pipe #@4” tube, filter to cooler (25, 30HP) S tube, filter to cooler (40HP) screw, hex set %@16” x !@2” clip, retainer shroud, fan (25, 30HP) S shroud, fan (40HP) valve, thermal (II) elbow, 90_ pipe 1” tube, thermal valve to filter cooler, fluid (25, 30HP) S cooler, fluid (40HP) nipple, pipe #@4” x 2” (40HP) elbow, 90_ pipe #@4” (40HP) screw, hex serrated washer %@16” x !@2” tube, cooler, sump (40HP) support, cooler (40HP) tubing, steel !@4” elbow, tube---f !@4” x !@8” nipple, pipe galvanized !@8” x 1!@2” nipple, !@4” x close elbow, reducing #@8” x !@4” bushing, reducing 1” x #@4” plate, adapter

standard part number

24KT part number

quantity

041007 807800---020 810504---012 250025---521

041007 807800---020 810504---012 250025---521

1 1 1 1

232942

232942

1

221706 822112---090 822112---135 802105---030 802415---030 232940 221704 250010---322 861505---140 011994 013315 250025---620 801515---040 232939 241852 044531 822112---020 801515---030 829705---050 221706 014690 841015---004 810404---012 823102---015 823204---000 801601---015 802104---030 224076

221706 822112---090 822112---135 802105---030 802415---030 232940 221704 250010---322 861505---140 011994 013315 250025---620 801515---040 232939 241852 044531 822112---020 801515---030 829705---050 221706 014690 841015---004 810404---012 823102---015 823204---000 801601---015 802104---030 224076

1 1 1 1 1 1 1 2 5 1 1 1 1 1 1 1 1 1 2 1 1 10 ft. 1 1 1 1 1 1

(I) For maintenance on fluid filter no. 250025---521, order repair kit no. 250025---525. (II) For maintenance on thermal valve no. 250025---620, order repair kit no. 250025---621.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

11

Section 1

ILLUSTRATIONS AND PARTS LIST 1.6 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (25 AND 30HP)

12

Section 1

ILLUSTRATIONS AND PARTS LIST 1.6 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (25 AND 30HP) key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

description

standard part number

24KT part number

switch, pressure water cover, motor shaft nipple, pipe #@4” x 2!@2” elbow, 45_ #@4” elbow, 90_ tube #@4” x #@4” tube, fluid stop elbow, tube !@4” x !@8” tubing, copper !@4” elbow, 90_ tube !@4” x !@4” elbow, reducing 1” x #@4” nipple, pipe 1” x 2!@2” locknut, conduit !@2” elbow, reducing 1!@4” x #@4” filter, fluid (I) bushing, hex 1!@4” x #@4” connector, tube #@4” x #@4” tube, filter/cooler cooler, fluid nut, hex ser washer plated %@16”---18 nipple, close #@4” tee, reducing #@4” x !@2” x #@4” nipple, close !@2” valve, globe !@2” plug, pipe !@2” tube, cooler/sump screw, hex ser washer %@16” x #@4” screw, hex 8.8M10 x 75mm tee, reducing 1” x !@2” x 1” tie wrap, plastic nipple, pipe 1” x 6” bushing, hex !@2” x !@4” tee, reducing #@4” x !@2” x !@2” nipple, pipe !@2” x 1!@2” union, pipe !@2” valve, water regulator !@2” nipple, pipe 1!@4” x 6”

250017---992 012266 822112---025 801415---030 810512---075 232823 810504---012 840115---004 810504---025 801604---030 822216---025 847200---050 801605---030 250025---521 802105---030 810212---075 221703 043096 825305---283 822212---000 802203---023 822208---000 041007 807800---020 221705 829705---075 828010---075 802204---024 843200---025 822116---060 802102---010 802203---022 822108---015 802515---020 041265 822120---060

250017---992 012266 822112---025 801415---030 810512---075 232823 810504---012 840115---004 810504---025 801604---030 822216---025 847200---050 801605---030 250025---521 802105---030 810212---075 221703 043096 825305---283 822212---000 802203---023 822208---000 041007 807800---020 221705 829705---075 828010---075 802204---024 843200---025 822116---060 802102---010 802203---022 822108---015 802515---020 041265 822120---060

quantity 1 1 1 1 3 1 2 5 ft. 1 2 2 1 1 1 1 3 1 1 4 2 1 1 1 1 1 4 2 1 2 1 1 1 2 1 1 1

(continued on Page 15) (I) For maintenance on fluid filter no. 250025---521, order repair kit no. 250025---525. PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

13

Section 1

ILLUSTRATIONS AND PARTS LIST 1.6 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (25 AND 30HP)

14

Section 1

ILLUSTRATIONS AND PARTS LIST 1.6 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (25 AND 30HP) (Cont’d.) key number 37 38 39 40 41

description

standard part number

24KT part number

quantity

washer, flat #@8” tube, steel #@4” 16 gauge nipple, !@8” x close elbow, !@4” x !@8” FNPT screw, %@16” x !@2”

838206---071 841115---012 823202---000 810404---012 829705---050

838206---071 841115---012 823202---000 810404---012 829705---050

2 1!@2 ft 1 1 2

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

15

Section 1

ILLUSTRATIONS AND PARTS LIST 1.7 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (40HP)

16

Section 1

ILLUSTRATIONS AND PARTS LIST 1.7 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (40HP) key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

description

standard part number

24KT part number

tubing, copper !@4” washer, plain b---regular #@8” nipple, pipe 1” x 4” tee, reducing 1” x #@4” x #@4” bushing, hex #@4” x !@2” connector, tube #@4” x #@4” elbow, 90_ tube !@4” x !@8” locknut, conduit !@2” switch, water pressure cover, motor shaft nipple, pipe #@4” x 2!@2” elbow, 45_ pipe #@4” elbow, 90_ tube #@4” x #@4” tube, fluid stop/unit elbow, reducing 1!@4” x #@4” elbow, 90_ tube !@4” x #@8” nipple, close 1!@2” x close nipple, pipe 1” x 6” elbow, reducing 1!@2” x 1” plate, support tee, reducing #@4” x !@2” x #@4” nipple, close !@2” valve, globe !@2” plug, pipe !@2” steel tube, sump/oil cooler filter, fluid (I) bushing, reducing 1!@4” x #@4” tube, oil cooler/filter bushing, hex 1!@2” x #@4” nipple, pipe #@4” x 3” valve, water regulator #@4” clamp, retaining 4!@2” heat exchanger 4” x 24” nipple, close #@4” union, #@4” screw, 8.8M10 x 75mm

840115---004 837206---071 822116---040 802204---033 802103---020 810212---075 810504---012 847200---050 250017---992 014996 822112---025 801415---030 810512---075 232823 801605---030 810504---038 822224---000 822120---060 801606---040 227158 802203---023 822208---000 041007 807800---020 227076 250025---521 802105---030 227074 802106---030 822112---030 041266 041983 042657 822212---000 802515---030 828010---075

840115---004 837206---071 822116---040 802204---033 802103---020 810212---075 810504---012 847200---050 250017---992 014996 822112---025 801415---030 810512---075 232823 801605---030 810504---038 822224---000 822120---060 801606---040 227158 802203---023 822208---000 041007 807800---020 227076 250025---525 802105---030 227074 802106---030 822112---030 041266 041983 042657 822212---000 802515---030 828010---075

quantity 6 ft. 20 1 1 1 3 2 1 1 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 3 1 2

(continued on Page 19) (I) For maintenance on fluid filter no. 250025---521, order repair kit no. 250025---525. PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

17

Section 1

ILLUSTRATIONS AND PARTS LIST 1.7 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (40HP)

18

Section 1

ILLUSTRATIONS AND PARTS LIST 1.7 COMPRESSOR COOLING AND LUBRICATION SYSTEM -- WATER-- COOLED (40HP) (Cont’d.) key number 37 38 39 40 41

description

standard part number

24KT part number

quantity

washer, flat #@8” tube, steel #@4” 16 gauge screw, %@16” x !@2” elbow, !@4” x !@8” FNPT nipple, !@8” x close

838206---071 841115---012 829705---050 810404---012 823202---000

838206---071 841115---012 829705---050 810404---012 823202---000

2 1!@2 ft 2 1 1

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

19

Section 1

ILLUSTRATIONS AND PARTS LIST 1.8 COMPRESSOR DISCHARGE SYSTEM

20

Section 1

ILLUSTRATIONS AND PARTS LIST 1.8 COMPRESSOR DISCHARGE SYSTEM key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

description

standard part number

24KT part number

switch, pressure 10---250# spot open locknut, conduit !@2” valve, check !@4” (I) connector, tube---m !@4” x !@8” tubing, steel !@4” 20 gauge connector, !@2” conduit, !@2” elbow, 90_ conduit coupling, conduit probe, temperature (24KT) S probe, temperature (std.) tee, reducing 1!@2” x !@2” x 1!@2” nipple, close 1!@2” x close (25 & 30HP) S nipple, close 1!@2” x 3” (40HP) elbow, tube 90_ !@4” x !@8” tee, tube !@4” x !@4” tee, reducing !@2” x !@4” x !@2” nipple, close !@2” valve, pressure relief !@2” connector, tube---m 1” x 1” bushing, reducing hex 1!@4” x 1” valve, minimum pressure (II) connector, flex !@4” x !@4” tube, return line strainer, v---type (III) glass, oil sight coupling, flexible (std.) (IV) S coupling, flexible (24KT) (V) nipple, pipe 1!@4” x 2!@2” capscrew, hex gr5 !@2”---13 x 1!@4” washer, springlock !@2” elbow, tube---m 90_ !@4” x !@4”

250017---991 847200---050 049905 810204---012 841115---004 846400---050 846215---050 846600---050 250007---179 --040588 802206---026 822224---000 822124---030 810504---012 810904---025 802202---012 822208---000 250006---938 810216---100 802105---040 241581 020169 220700 241771 046559 040033 --822120---025 828608---125 837508---125 810504---025

250017---991 847200---050 049905 810204---012 841115---004 846400---050 846215---050 846600---050 250007---179 046867 --802206---026 822224---000 822124---030 810504---012 810904---025 802202---012 822208---000 250006---938 810216---100 802105---040 241581 020169 220700 241771 046559 --250007---544 822120---025 828608---125 837508---125 810504---025

quantity 1 2 1 1 6 ft. 1 3 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 8 1

(continued on Page 23) (I) For maintenance on check valve no. 049905, order replacement spring no. 250003---657. (II) For maintenance on minimum pressure valve no. 241581, order seal kit no. 250026---758. (III) For maintenance on v---type strainer no. 241771, order repair kit no. 241772. (IV) For maintenance on flexible coupling no. 040033, order gasket kit no. 040517. (V) For maintenance on flexible coupling no. 250007---544, order gasket kit no. 250007---559. PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

21

Section 1

ILLUSTRATIONS AND PARTS LIST 1.8 COMPRESSOR DISCHARGE SYSTEM

22

Section 1

ILLUSTRATIONS AND PARTS LIST 1.8 COMPRESSOR DISCHARGE SYSTEM (continued) key number 30 31 32 33 34 35 36 37 38 39 40 41 42 43

description nipple, half 1!@2” x 5!@2” tank, sump element, separator (25 & 30HP) (II) S element, separator (40HP) (I) (II) gauge, temperature 2” cap, fluid fill adapter, fill cap tee, reducing 1” x 1” x 1!@2” glass, sight capscrew, hex head gr8 !@2”x1!@2” (25,30HP) Scapscrew, !@2”---13 x 2!@4” (40HP) nipple, close !@4” 6aw galv washer, springlock !@2” nut, hex !@2”---13 washer, !@2” flat spacer (40HP)

standard part number

24KT part number

quantity

822824---055 047070 250034---111 250034---111 042582 040029 020044 802204---046 041327

822824---055 047070 250034---113 250034---113 042582 040029 020044 802204---046 041327

1 1 1 1 1 1 1 1 1

828608---150 828608---225 823204---000 837508---125 824208---448 838208---112 232684

828608---150 828608---225 823204---000 837508---125 824208---448 838208---112 232684

2 2 2 2 2 2 129

(I) For maintenance on separator element (std.) no. 250034---111, order repair kit no. 250034---112. (II) For maintenance on separator element (24KT) no. 250034---113, order repair kit no. 250034---114.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

23

Section 1

ILLUSTRATIONS AND PARTS LIST 1.9 ELECTRICAL BOX

24

Section 1

ILLUSTRATIONS AND PARTS LIST 1.9 ELECTRICAL BOX key number 1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18 19

20 21 22 23 24 25 26 27

description gasket, motor/starter mount (25 & 30HP) S gasket, motor/starter mount (40HP) washer, #10 external tooth adaptor, motor (25 & 30HP) S adaptor, motor (40HP) gasket, starter nut, hex %@16”---18 screw, %@16”---18 x #@4” (25, 30HP) Sscrew, %@16”---18 x #@4” (40HP) adapter, motor/starter (25, 30HP) bar, 1” x 2” x 3” (40HP) screw, serrated washer %@16”---18 x #@4” (25, 30HP) Sscrew, serrated washer %@16”---18 x 1!@2” (40HP) hourmeter, 2!@2” 120V 60Hz gasket, hourmeter nameplate, START pushbutton, START assembly nameplate, STOP pushbutton, STOP assembly lug, scrulug 4 str 1/0 str %@16” wrap, tie plastic 26m !@16” x 1#@4” starter, N3 open S starter, N4 open transformer, 380/416V S transformer, 208V S transformer, 230/460V S transformer, 600V plug, hole !@2” clip, plastic control, temperature (KT only) screw, #@8” x 16 x #@4” (25, 30HP) washer, #@8” springlock (25, 30HP) washer, %@16” external tooth track, snap mounting screw, 8---32 x !@2”

standard part number

24KT part number

quantity

250030---147 405159 838402---025 250027---818 250027---890 220790 825305---283 829705---075 829705---075 250021---278 040632

250030---147 405159 838402---025 250027---818 250027---890 220790 825305---283 829705---075 829705---075 250021---278 040632

1 1 2 1 1 2 7 7 5 1 2

829705---075

829705---075

2

829705---150 042988 410353 250023---049 250016---351 250023---050 250016---350 849215---025 843200---025 052362 052036 250028---878 250028---872 250028---721 250028---884 045689 041632 --828606---075 837506---094 838405---034 250024---522 835601---050

829705---150 042988 410353 250023---049 250016---351 250023---050 250016---350 849215---025 843200---025 052362 052036 250028---878 250028---872 250028---721 250028---884 045689 041632 409270 828606---075 837506---094 838405---034 250024---522 635601---050

2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 2 2 1 4 4 6 1 2

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

25

Section 1

ILLUSTRATIONS AND PARTS LIST 1.10 PNEUMATIC CONTROLS

26

Section 1

ILLUSTRATIONS AND PARTS LIST 1.10 PNEUMATIC CONTROLS key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

description

standard part number

24KT part number

valve, solenoid !@4” 3---way (I) bushing, conduit plastic !@2” locknut, conduit !@2” nut, hex serrated washer %@16” elbow, pipe 90_ !@4” nipple, pipe !@4” x 4!@2” nipple, pipe !@4” x close tee, pipe !@4” strainer, v---type (II) tubing, steel !@4” tee, tube---m !@4” x !@4” x !@4” elbow, tube---m !@4” x !@4” valve, pressure regulator (III) connector, tube---m !@4” x !@4” valve, check !@4” orifice, pipe plug !@4” valve, air inlet 2!@2” (IV) valve, blowdown !@4” (V) bushing, reducing !@4” x !@8” silencer, !@8” tee, tube union !@4” screw, 8---32 x #@8” elbow, tube---m !@4” x !@8” nipple, chase conduit !@2” screw, 10---32 x !@2” washer, springlock #10 nut, 10---32 screw, hex serrated washer %@16” x #@4” bracket, pressure switch switch, pressure

250017---993 848815---050 847200---050 825305---283 803515---010 823104---045 823204---000 804415---010 241771 841015---004 810804---025 810504---025 250017---280 810204---025 049905 232874 250025---654 250025---655 807600---005 043196 811404---025 835601---038 810504---012 847815---050 831702---050 838502---047 825801---130 829705---075 250018---146 040694

250017---993 848815---050 847200---050 825305---283 803515---010 823104---045 823204---000 804415---010 241771 841015---004 810804---025 810504---025 250017---280 810204---025 049905 232874 250025---654 250025---655 807600---005 043196 811404---025 835601---038 810504---012 847815---050 831702---050 838502---047 825801---130 829705---075 250018---146 040694

quantity 1 1 4 2 4 1 8 1 1 6 ft. 1 3 1 2 1 1 1 1 1 1 1 2 1 1 2 2 2 2 1 1

(continued on Page 29) (I) For maintenance on solenoid valve no. 250017---993, order repair kit no. 250018---970. (II) For maintenance on v---type strainer no. 241771, order repair kit no. 241772. (III) For maintenance on pressure regulator valve no. 250017---280, order repair kit no. 250019---453. (IV) For maintenance on air inlet valve no. 250025---654, order repair kit no. 250019---451. (V) For maintenance on blowdown valve no. 250025---655, order repair kit no. 250031---772.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

27

Section 1

ILLUSTRATIONS AND PARTS LIST 1.10 PNEUMATIC CONTROLS

28

Section 1

ILLUSTRATIONS AND PARTS LIST 1.10 PNEUMATIC CONTROLS (continued) key number 31 32 33 34 35 36 37

description

standard part number

24KT part number

quantity

elbow, corner pull 90_ !@2” nipple, conduit !@2” x !@2” bracket, solenoid valve support screw, tc---f pan #10---24 x !@2” washer, loc ext #10 tee, tube m---run !@4” x !@4” pipe, cross !@4”

846915---050 250007---169 250030---037 835602---050 838402---025 810904---025 803315---010

846915---050 250007---169 250030---037 835602---050 838402---025 810904---025 803315---010

1 3 1 2 4 1 1

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

29

Section 1

ILLUSTRATIONS AND PARTS LIST 1.11 INSTRUMENT PANEL -- OPEN AND ENCLOSURE OPTION

30

Section 1

ILLUSTRATIONS AND PARTS LIST 1.11 INSTRUMENT PANEL -- OPEN AND ENCLOSURE OPTION key number 1 2 3 4 5 6 7 8 9 10 11

description

standard part number

24KT part number

quantity

gauge, temperature gauge, air pressure gauge, separator maintenance gauge, fluid filter maintenance panel, instrument (open) connector, tube---f !@4” x !@8” tee, tube---f run !@4” x !@8” nut, hex serrated washer plated %@16”---18 screw, hex serrated washer %@16” x #@4” tubing, steel !@4” label, instrument panel

042582 250005---185 250003---798 250003---799 250003---873 810104---012 811004---012 825305---283 829705---075 840115---004 250004---977

042582 250005---185 250003---798 250003---799 250003---873 810104---012 811004---012 825305---283 829705---075 840115---004 250004---977

1 2 1 1 1 5 1 2 2 10 1

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

31

Section 1

ILLUSTRATIONS AND PARTS LIST 1.12 AIR-- COOLED AFTERCOOLING OPTION (25 AND 30HP)

32

Section 1

ILLUSTRATIONS AND PARTS LIST 1.12 AIR-- COOLED AFTERCOOLING OPTION (25 AND 30HP) key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

description

standard part number

24KT part number

quantity

screw, hex head ser wash %@16” x #@4” panel, cooler adapter nut, retainer “J” %@16”---18 nut, hex serrated wash plated %@16”---18 elbow, 1” x #@4” mnpt (25, 30HP) Selbow, 90_ tube 1” x 1” (40HP) tube, aftercooler/check valve (25, 30HP) S tube, aftercooler/check valve (40HP) connector, tube 1” x 1” bushing, hex 1!@4” x 1” bushing, hex 2” x 1” separator/trap (I) elbow, reducing 2” x 1!@2” bracket, mount trap washer, springlock regular !@2” nut, hex !@2”---13 capscrew, hex head gr5 !@2” x 1!@2” tube, aftercooler/separator (25, 30HP) S tube, aftercooler/separator (40HP) aftercooler, (25, 30HP) S aftercooler, (40HP)

829705---075 224076 861405---092 825305---283 810516---075 810516---100 221700 250026---954 810216---100 802105---040 802108---040 040847 801608---060 021481 837508---125 824208---448 828608---150 232968 250026---955 407106 241852

829705---075 224076 861405---092 825305---283 810516---075 810516---100 221700 250026---954 810216---100 802105---040 802108---040 040847 801608---060 021481 837508---125 824208---448 828608---150 232968 250026---955 407106 241852

6 1 4 2 2 2 1 1 2 1 1 1 1 1 2 2 2 1 1 1 1

(I) For maintenance on separator/trap no. 040847, order repair kit no. 044374.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

33

Section 1

ILLUSTRATIONS AND PARTS LIST 1.13 WATER-- COOLED AFTERCOOLING OPTION (25 AND 30HP)

34

Section 1

ILLUSTRATIONS AND PARTS LIST 1.13 WATER-- COOLED AFTERCOOLING OPTION (25 AND 30HP) key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

description

standard part number

24KT part number

quantity

bracket, mount trap separator/trap (I) heat exchanger tube, aftercooler/oil cooler tube, aftercooler/separator tube, MPV/aftercooler elbow, 90_ pipe 1” elbow, reducing 2” x 1!@2” bushing, hex 1!@4” x 1” bushing, hex 2” x 1” connector, tube %@8” x !@2” connector, tube 1” x 1” elbow, 90_ tube 1” x 1” nipple, pipe 1” x 5” nut, hex !@2”---13 nut, hex serrated washer %@16”---18 capscrew, hex gr5 !@2” x 1!@2” screw, hex serrated washer %@16” x #@4” washer, springlock regular !@2” cap, inlet ---outlet cap, reversing gasket, inlet ---outlet gasket, reversing cap bushing, reducing #@4” x !@2”

021481 040847 043096 221699 250026---956 232829 801515---040 801608---060 802105---040 802108---040 810210---050 810216---100 810516---100 822116---050 824208---448 825305---283 828608---150 829705---075 837508---125 044244 044245 044242 044243 802103---020

021481 040847 043096 221699 250026---956 232829 801515---040 801608---060 802105---040 802108---040 810210---050 810216---100 810516---100 822116---050 824208---448 825305---283 828608---150 829705---075 837508---125 044244 044245 044242 044243 802103---020

1 1 1 1 1 1 1 1 1 1 2 3 1 1 2 4 2 4 2 1 1 1 1 2

(I) For maintenance on separator/trap no. 040847, order repair kit no. 043374.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

35

Section 1

ILLUSTRATIONS AND PARTS LIST 1.14 WATER-- COOLED AFTERCOOLING OPTION (40HP)

36

Section 1

ILLUSTRATIONS AND PARTS LIST 1.14 WATER-- COOLED AFTERCOOLING OPTION (40HP) key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

description

standard part number

24KT part number

quantity

washer, flat #@8” tube, MPV/aftercooler connector, tube 1” x1” bushing, hex 1!@4” x 1” bushing, hex 1!@2” x 1” bushing, hex 1” x #@4” connector, tube #@4” x #@4” tube, separator/aftercooler bushing, hex 2” x 1” separator/trap (I) S heater (optional) elbow, reducing 2” x 1!@2” bracket, mount trap washer, springlock regular !@2” nut, hex !@2”---13 capscrew, hex head gr5 !@2” x 1!@2” tube, aftercooler/oil cooler elbow, #@4” x #@4” mnpt nut, %@16”---18 gasket, reversing cap heat exchanger elbow, tube 1” x 1” cap, inlet ---outlet cap, reversing gasket, inlet ---outlet cap screw, %@16” x #@4”

838206---071 227075 810216---100 802105---040 802106---040 802104---030 810212---075 227077 802108---040 040847 245572 801608---060 021481 837508---125 824208---448 828608---150 227078 810212---075 825305---283 044221 043062 810516---100 044229 044228 044220 829705---075

838206---071 227075 810216---100 802105---040 802106---040 802104---030 810212---075 227077 802108---040 040847 245572 801608---060 021481 837508---125 824208---448 828608---150 227078 810212---075 825305---283 044221 043062 810516---100 044229 044228 044220 829705---075

4 1 3 1 2 1 1 1 1 1 1 1 1 4 2 2 1 1 4 1 1 1 1 1 1 4

(I) For maintenance on separator/trap no. 040847, order repair kit no. 044374.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

37

Section 1

ILLUSTRATIONS AND PARTS LIST 1.15 WATER-- COOLED AND AIR-- COOLED ENCLOSURE AND PARTS -- OPTION

38

Section 1

ILLUSTRATIONS AND PARTS LIST 1.15 WATER-- COOLED AND AIR-- COOLED ENCLOSURE AND PARTS -- OPTION key number 1 2 3 4 5

6 7

8 9 10 11 12

13 14 15 16 17 18 19 20

21 22 23 24 25 26 27 28 29 30

description panel, roof panel, fiberglass 5” x 35!@2” grill, cooler (air---cooled) nut, retainer “J” %@16”---18 u---clip screw, hex serrated washer %@16” x #@4” (air---cooled) S screw, hex serrated washer %@16” x #@4” (water---cooled) panel, access panel, fiberglass 15!@4” x 32!@2” (air---cooled) S panel, fiberglass 15!@4” x 32!@2” (water---cooled) weatherstrip, felt panel, enclosure center guard, fan 13” washer, springlock regular !@4” (AC) Swasher, springlock regular !@4” (WC) capscrew, hex head gr5 !@4”---20 x 1” (air---cooled) S capscrew, hex head gr5 !@4”---20 x 1” (water---cooled) panel, end fan, enclosure nut, hex !@4”---20 rivet, tubular !@4”---20 nut, hex !@2”---13 panel, fiberglass 13” x 36!@2” panel, enclosure --- right hand nut, hex serrated washer pltd %@16”---18 (air---cooled) nut, hex serrated washer pltd %@16”---18 (water---cooled) panel, enclosure --- left hand frame, enclosure panel, cooler end (air---cooled) clamp, speed !@4” (air---cooled) latch, door (air---cooled) latch, door (water---cooled) panel, access panel, enclosure front capscrew, hex head gr5 !@2” x 1!@2” washer, springlock regular !@2” nut, retainer (air---cooled)

standard part number

24KT part number

quantity

250018---316 049889---035 242095 861505---140

250018---316 049889---035 242095 861505---140

2 4 1 14

829705---075

829705---075

40

829705---075 014620

829705---075 014620

36 2

049889---005

049889---005

6

049889---005 043502 224585 241579 837504---062 837504---062

049889---005 043502 224585 241579 837504---062 837504---062

7 75 ft. 3 1 6 12

829104---100

829104---100

6

829104---100 829104---100 02250043---677 02250043---677 241580 241580 824204---226 824204---226 049824 049824 824208---448 824208---448 049889---012 049889---012 224583 224583

12 1 1 4 8 4 4 2

825305---283

825305---283

28

825305---283 224584 014790 014812 043194 049764 049764 250018---708 250003---872 828608---150 837508---125 861405---092

825305---283 224584 014790 014812 043194 049764 049764 250018---708 250003---872 828608---150 837508---125 861405---092

24 2 1 1 4 3 5 1 1 4 4 4

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

39

Section 1

ILLUSTRATIONS AND PARTS LIST 1.16 HEAVY DUTY FILTER OPTION

40

Section 1

ILLUSTRATIONS AND PARTS LIST 1.16 HEAVY DUTY FILTER OPTION key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14

description nipple, close 2!@2” elbow, reducing 2!@2” x 2” (25, 30HP) S elbow, pipe 90_ 2!@2” (40HP) nipple, half 2” x 3” (25, 30HP) S nipple half 2!@2” x 3” (40HP) clamp, hose 1&@8” x 2#@4” (25, 30HP) S clamp, hose 3” (40HP) elbow, rubber (25, 30HP) S elbow, rubber (40HP) indicator, air filter maintenance support, air filter (25, 30HP) S bracket, air filter (40HP) filter, air (25, 30HP) (I) S filter, air (40HP) (II) screw, hex serrated washer %@16” x #@4” band, mounting (25, 30HP) S band, mounting (40 HP) nut, hex serrated washer plated %@16”---16 capscrew, hex head gr5 #@8” x 1!@4” (25, 30HP) washer, springlock regular #@8” (25, 30 HP) nut, hex #@8”---16 (25, 30HP)

standard part number

24KT part number

quantity

822240---000 801610---080 801515---100 822832---030 822840---030 040083 040343 044634 041960 045757 250042---848 015718 043333 040595 829705---075 043370 040598 825305---283

822240---000 801610---080 801515---100 822832---030 822840---030 040083 040343 044634 041960 045757 250042---848 015718 043333 040595 829705---075 043370 040598 825305---283

1 1 1 1 1 2 2 1 1 1 1 1 1 1 2 1 1 2

828606---125

828606---125

2

837506---094 824206---337

837506---094 824206---337

2 2

(I) For maintenance on air filter no. 043333, order replacement element no. 043334. (II) For maintenance on air filter no. 040595, order replacement element no. 040596.

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

41

Section 1

ILLUSTRATIONS AND PARTS LIST 1.17 OPTIONAL AIR TANK -- 120 AND 200 GALLON

42

Section 1

ILLUSTRATIONS AND PARTS LIST 1.17 OPTIONAL AIR TANK -- 120 AND 200 GALLON key number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

description

standard part number

24KT part number

quantity

tank, receiver (120 gallon) tank, receiver (200 gallon) nipple, pipe 1!@4” x close tee, side outlet 1!@4” bushing, hex 1!@4” x !@2” valve, pressure relief bushing, hex 1!@4” x !@4” nipple, close !@4” gauge, pressure elbow, pipe !@4” 90_ tee, pipe #@4” bushing, hex #@4” x #@8” bushing, hex 1!@4” x 1” elbow, pipe #@4” 45_ trap, automatic #@4” nipple, close #@8” xs plug, pipe 1!@4” nipple, close #@4” elbow, pipe #@4” nipple, pipe #@4” x 8” valve, globe plug, pipe #@8”

042878 042877 822220---000 802715---050 802105---020 043041 802105---010 823204---000 040691 803515---010 802415---030 802103---015 802105---040 801415---030 042034 822206---000 802815---050 822212---000 801515---030 822112---080 042733 807800---015

042878 042877 822220---000 802715---050 802105---020 043041 802105---010 823204---000 040691 803515---010 802415---030 802103---015 802105---040 801415---030 042034 822206---000 802815---050 822212---000 801515---030 822112---080 042733 807800---015

1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 4 3 1 1 1 1

248369

1

860216---075

1

860216---100

1

(ALL NON-- AFTER COOLED COMPRESSORS) hose, assembly 1” x 40” (25/30/40HP ac and wc) 248369 elbow, 37_ flare 90_m #@4” x 1” (25/30HP ac) 860216---075 elbow, 37_ flare 90_m 1” x 1” (25/30HP wc and 40HP ac) 860216---100

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

43

Section 1

ILLUSTRATIONS AND PARTS LIST 1.18 DECAL GROUP

1 2

3

4

5 6

7

8

9

44

10

Section 1

ILLUSTRATIONS AND PARTS LIST 1.18 DECAL GROUP key number 1 2 3 4 5 6 7 8 9 10

description

standard part number

24KT part number

quantity

decal, airanteed 2 year ---white sign, warning sever fan sign, warning sever fan port sign, danger electrocution decal, rotation decal, 460 volt decal, grounding lug decal, compressor fluid Sullube---32 decal, SRF 1/4000 fluid decal, 10---B---40HP maintenance kit

043067 049855 049965 049850 250021---286 040631 045433 250023---361 250022---839 250034---136

043067 049855 049965 049850 250021---286 040631 045433 250023---361 250022---839 250034---136

1 2 1 1 1 1 1 1 1 1

(Continued on Page 47)

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

45

Section 1

ILLUSTRATIONS AND PARTS LIST 1.18 DECAL GROUP

11

12

14

13 15

16

17

46

19

18 20

Section 1

ILLUSTRATIONS AND PARTS LIST 1.18 DECAL GROUP (Continued) key number 11 12 13 14 15 16 17 18 19 20 21 22

description

standard part number

24KT part number

quantity

sign, warning compressor oil fill cap sign, danger air breathing sign, warning “food grade” lube sign, warning ground fault decal, danger high voltage decal, water inlet/outlet decal, water in decal, water out decal, rotation decal, water drain decal, Sullair 16#@4” --- white (not shown) decal, logo --- white (not shown)

049685 250027---935 250003---144 049852 042218 049873 250019---107 250019---108 250021---564 250022---810 250014---057 040087A

049685 250027---935 250003---144 049852 042218 049873 250019---107 250019---108 250021---564 250022---810 250014---057 040087A

1 1 1 1 1 1 1 1 1 1 1 1

PLEASE NOTE: WHEN ORDERING PARTS, INDICATE SERIAL NUMBER OF COMPRESSOR

47

NOTES

NOTES

WORLDWIDE SALES AND SERVICE

SULLAIR CORPORATION A SUBSIDIARY OF SUNDSTRAND CORPORATION

3700 E. Michigan Blvd. Michigan City, Indiana 46360---9990 Telephone (219) 879---5451

R

Printed in U.S.A. Specifications Subject To Change Without Prior Notice