Current Transformers SM6 24 cubicles Feasibility range and referenced types Catalogue 2004 Number: C019 rev. 1 pag. 1/
Views 163 Downloads 10 File size 415KB
Current Transformers SM6 24 cubicles
Feasibility range and referenced types
Catalogue 2004 Number: C019 rev. 1 pag. 1/20
CONTENTS
CURRENT TRANSFORMER RECOMMENDATIONS FOR THE USE OF TABLES AND TECHNICALS NOTES
Page 3,4,5 and 6
PANEL TYPE CRM REFERENCED TYPES
ARJP1/N2 F ARJP2/N2 F
Page 7 Page 11
CONFIGURED TYPES
ARJP1/N1 F and ARJP1/N2 F ARJP2/N1 F, ARJP2/N2 F and ARJP2/N3 F
Page 8 and 9 Page 12 and 13
REFERENCED TYPES
ARJP1/N2 F
Page 7
CONFIGURED TYPES
ARJP1/N1 F and ARJP1/N2 F
Page 8 and 9
PANEL TYPE QMC
PANEL TYPE DMV-A, DMV-D, IMC REFERENCED TYPES
ARJP2/N2 F
Page 11
CONFIGURED TYPES
ARJP1/N1 F and ARJP1/N2 F ARJP2/N1 F, ARJP2/N2 F and ARJP2/N3 F
Page 8 and 9 Page 12 and 13
PANELS TYPE 1250A
DM1-A, DM1-D, DM1-W, DM1-Z, GBC-A, GBC-B, DMV-A, DMV-D
REFERENCED TYPES
ARJP3/N2 F
Page 15
CONFIGURED TYPES
ARJP3/N1 F, ARJP3/N2 F and ARJP3/N3 F
Page 16
PANELS TYPE DM1-A, DM1-D, DM1-W, DM2, GBC-A, GBC-B REFERENCED TYPES
ARM3/N2 F
Page 18
CONFIGURED TYPES
ARM3/N1 F and ARM3/N2 F
Page 19
NOTE:
N1, N2 and N3 MEAN THE NUMBER OF SECONDARIES F MEANS THAT THERE IS NOT BASE PLATE
pag. 2/20
CURRENT TRANSFORMERS
PREFERABLY USE the equipment selected and marked as REFERENCED
RECOMMENDATIONS FOR THE USE OF THE FEASIBILITY AND COMPUTATION SUPPORTS
_______________ ¶
CHECK NEEDS AND NECESSARY INFORMATION ACCURATELY
·
USE EQUIPMENT MARKED AS REFERENCE
¸
CHECK READLY AVAILABLE FEASIBILITY SECTIONS DIRECTLY TO APPLY KEYS TO FEASIBILITY TABLES CORRECTLY, PLEASE SEE ON PAGE 4
¹
USE ALSO ELONET TO CHECK FEASIBILITY
º
CONSULT US IF FEASIBILITY RANGE IS NOT AVAILABLE OR FOR OTHERS CHARACTERISTICS
pag. 3/20
KEYS TO THE VARIOUS TABLES TO DEFINE FEASIBILITY
1)
Define Ipn rated primary current Use primary values defined by standard (IEC): 10, 12,5, 20, 25, 30, 40, 50, 60 and 75 A and their decimal multiples.
2)
Define Ith rated short-time thermal current for 1 second Short-circuit current usually lasts 1 second. Should this value be different (equal to a lenght "t"), calculate the following:
Ith (for 1 sec.) = Ith x √t example:
3)
25 kA for 3 sec. >> 25 x √3 = 43,3 kA for 1 sec.
Calculate coefficient "K" The above reperesents the key to the various tables
Ith for 1 sec.
K= example:
4)
Ipn
Ipn = 100 A , Ith = 12,5 kA 1 sec. >> K = 12500 / 100 = 125
Finding position on the table Locate column "K" and stop on the line corresponding to a value higher than K. example:
5)
K calculate value = 125 >> ligne K = 150
Check feasibility A possible current transformer will feature the performances shown in the columns identified by boxes : For perotection secondary is true, only for choosing in the catalogue, the following formule:
VA x FL = constant example: 10VA 5P10 ( VA x FL= 10 x 10= 100 ) >> 5VA 5P20 ( VA x FL= 5 x 20= 100 )
pag. 4/20
TECHNICAL NOTES Diagrams of the terminals markings according to IEC standard.
SINGLE RATIO P1
P2
P1
S1
S2
1S1
CT with ONE SECONDARY WINDING
P2
1S2
2S1
2S2
P1
1S1
CT with TWO SECONDARY WINDINGS
P2
1S2 2S1 n da
2S2
3S1 dn
3S2
CT with THREE SECONDARY WINDINGS
F WARNING ! The secondary open winding of a CT is dangereus! The unused secondary windings of a CT must be short-circuited. pag. 5/20
Current transformer with DOUBLE RATIO through primary coulping. types ARM3 Burden values are the same for both ratios. P1
C1
C2
P2
SERIAL PRIMARY COUPLING LOW RATIO
P1
C1
C2
P2
PARALLEL PRIMARY COUPLING HIGH RATIO
Current transformer with DOUBLE RATIO through connection on secondary. types ARJP1, ARJP2, ARJP3
P1
S1
S2
P2
P1
S3
1S1
CT with ONE SECONDARY WINDING
P2
1S2
1S3 2S1
2S2
2S3
CT with TWO SECONDARY WINDINGS
S1-S2 LOW RATIO S1-S3 HIGH RATIO
1S1-1S2 2S1- 2S2 1S1-1S3 2S1- 2S3
LOW RATIO HIGH RATIO
H Burden values are different for each of the two ratios
F WARNING ! The secondary open winding of a CT is dangereus! The unused secondary windings of a CT must be short-circuited. pag. 6/20
REFERENCED CURRENT TRANSFORMERS Type ARJP1/N2 F Panel type CRM - QMC
Dimensions
Drawing n° H 103441
Characteristics
Standard reference IEC 60044-1 Rated highest voltage : 24 kV Rated continous thermal current 1,2 x In Frequency 50 and 60 Hz
CTs type ARJP1/N2F Reference number
Ratio
Short-time current I th t (kA) (s)
(A/A)
1st secondary
2nd secondary
51238639F0
10/5-5
1,2
1
15 VA cl. 0,5 Fs