• Author / Uploaded
• juan carlos

Citation preview

TECHNICAL SPECIFICATION LH203-3 (20.06.2007)

1/3

2460 mm (97 “)

1840 mm (72 “)

3500 mm (138 “)

Sandvik LH203

1235 mm (49 “)

1450 mm (60 “)

1,5 m³ (2.0 yd³) 260 mm (10 “)

525 mm (21 “)

2505 mm (97 “)

2195 mm (86 “)

1110 mm (44 “)

6970 mm (274 “)

‘

1480 mm (58 “)

1660 mm (65 “)

1740 mm (70 “)

44°

40°

14 20 m m (5 6

R2735 mm (108 “)

“)

2800 mm (110 “)

R4730 mm (186 “)

Note: Dimensions subject to bucket options SANDVIK MINING AND CONSTRUCTION OY reserves the right to change this specification without further notice

ISO 9001

ISO 14001

CERTIFICATED FIRM

CERTIFICATED FIRM

Sandvik Mining and Construction Oy Loaders Turku P.O. Box 434 20101 Turku, Finland Tel. +358 205 44 131 Fax +358 205 44 130 e-mail: [email protected] Internet: www.smc.sandvik.com

Sandvik LH203 Main dimensions 6 970 mm (274") 1 420 mm (56") 1 480 mm (58") 1 595 mm (63”) 1 840 mm (72") or 1 740 mm (69”)

Weights Operating weight 8700 kg (19 180 lb) Total loaded weight 12 200 kg (26 897 lb) Shipping weight 8500 kg (18 739 lb) Axle weights without load: front axle 3700 kg (8 157 lb) rear axle 5000 kg (11 023 lb) Axle weights with load: front axle 9050 kg (19 952 lb) rear axle 3150 kg (6 945 lb) Unit weight is dependent on the selected options

Capacities 3500 kg (7 716 lb) 61 kN (6 220 kg) (13 710 lb) 55 kN (5 600 kg) (12 360 lb) 8300 kg (18 298 lb) 1,5 m³ (2.0yd³), HB500/400

Bucket motion times Raising time Lowering time Tipping time

5.5 s 2.9 s 3.0 s

Driving speeds forward and reverse 1st gear 2nd gear 3rd gear

5.0 km/h (3.1 mph) 9.3 km/h (5.8 mph) 24.0 km/h (14.9 mph)

Frame Rear and front frame Material Central hinge

Welded steel construction Raex Multisteel N (St/Fe 355) Box constructed, adjustable

Standard engine Diesel engine Output Torque Number of cylinders Displacement Cooling system Combustion principle Electric system Air filtering Exhaust system Fuel tank capacity

Engine DEUTZ BF6L914 71,5 kW/2300 r/min (95 hp) 400 Nm 1650 r/min 6 6472 cm³ Air cooled Turbo charged, direct injection, four stroke 24V Donaldson Double wall exhaust pipe with catalytic purifier / muffler 130 l (43 gal.)

Standard converter Dana SOH, C 2122

Gearbox Dana SOH, RT20324

2/3

Standard tyres

Total length Width without bucket Maximum width Height without safety canopy Height with safety canopy

Tramming capacity Breakout force, lift Breakout force, tilt Tipping load Bucket std.

TECHNICAL SPECIFICATION LH203-3 (20.06.2007)

Power shift (mechanical gear shift control) transmission, three gears forward and reverse

Standard axles Front axle

Dana SOH, 14D 1441 LCB, No-Spin differential, fixed Rear axle Dana SOH, 14D 1441 LCB, oscillating ± 10° Oscillation stabilizer SANDVIK MINING AND CONSTRUCTION OY reserves the right to change this specification without further notice

Size and type

12.00 x 20 L5S, NOKIA (brand and type of the tyres subject to availability) Air pressure, front 600 kPa (6,0 bar) (87.1 psi) Air pressure, rear 350 kPa (3,5 bar) (50.8 psi) Other type of tyres available to user’s choice. In certain applications the productive capabilities of the loader may exceed the TKPH value given by tyre manufacturer. Sandvik Mining and Construction Oy recommends that the user consult their tyre supplier to evaluate conditions and to find the best solution for application.

Standard Canopy ROPS/FOPS certified safety canopy. Height

1840 mm (72”)

Steering hydraulics Full hydraulic, centre-point articulation, power steering with one double acting cylinder. Steering controlled by stick. Emergency steering is optional. Turning angle ±40° Turning radius (with std bucket): inner 2735 mm (107 ") outer 4730 mm (186") Main components in steering system: Main valve Rexroth Servo control valve Rexroth Steering cylinder ø 100 mm (3,9"), Tamrock Steering and servo hydraulic pumps Rexroth Pressure settings: Steering hydraulics 15.0 MPa (150 bar) Shock load valves 20.0 MPa (200 bar)

Bucket hydraulics Dual stick bucket and boom control. Full hydraulic, mechanically controlled system, equipped with one gear type pump. Oil flows to bucket hydraulic system from the main pump and from the steering hydraulics. Main components: Boom system Direct dump Lift cylinder ø 180 mm (7.1"), Tamrock Tilt cylinder ø 140 mm (5.5"), Tamrock Servo control valve Rexroth Main valve Rexroth Pump for bucket hydraulics Rexroth Fittings JIC Pressure setting for: Bucket hydraulics 21.0 MPa (210 bar) Relief valves 24.0 MPa (240 bar) Piston side of the cylinder 6.0 MPa (60 bar) Hydraulic oil tank capacity appr. 120 l (32 gal)

Standard brakes Service brakes are hydraulically operated multi-disc brakes on all wheels with two separate circuits for the front and rear axle. Parking brake is spring applied, hydraulically released dry disk brake affecting on the front axles drive line. In case of a sudden pressure drop in brake hydraulics the parking brake functions also as an emergency brake. Main components in the brake system: Pressure accumulator Bosch Brake pedal valve Wabco Parking brake Tamrock Charging valve Mico

Standard Lubrication system Centralized manual lubrication

ISO 9001

ISO 14001

CERTIFICATED FIRM

CERTIFICATED FIRM

Sandvik Mining and Construction Oy Loaders Turku P.O. Box 434 20101 Turku, Finland Tel. +358 205 44 131 Fax +358 205 44 130 e-mail: [email protected] Internet: www.smc.sandvik.com

Sandvik LH203 Electrical equipment Alternator Batteries Starter Driving and working lights:

Parking and brake lights

TECHNICAL SPECIFICATION LH203-3 (20.06.2007)

3/3

Main options: 24 V 55 A, Bosch 2 x 12 V 70 Ah 4 kW, 24 V, Bosch 2 pcs in front, 65 W Nordic lights 2 pcs in rear, 65 W Nordic lights 2 pcs in front, 5W LED lights 2 pcs in rear 5 W LED lights

Electrical gauges

Others Decal language EU-languages

Standard manuals Instructions manual (1pc) - General mandatory safety instructions EU-languages - Start up of a new machine English - Operator’s manual EU-languages - Maintenance manual EU-languages Spare part manual (1pc) English Workshop manual (1pc) English ToolMan CD (2pcs) Manuals in pdf form - General mandatory safety instructions - Operator’s manual - Maintenance manual - Spare part manual

SANDVIK MINING AND CONSTRUCTION OY reserves the right to change this specification without further notice

* replaces standard equipment 3 3 • * Bucket size 1.5 m (2.0yd ), width 1690 mm (67”), HB500/400. 3 3 • * Bucket size 1.75 m (2.3yd ), width 1690 mm (67”), HB500/400. 3 3 • * Side tipping bucket 1.35 m , (1.8yd ), right. 3 3 • * Ejector bucket 1.5 m (2.0yd ). • Air filtering: oil bath and zyclone • * Electrical gear shifter. • * Automatic central lubrication. • Oil cooler for hydraulic • RRC HBC complete • RRC Cattron complete • RRC HBC interface • RRC Cattron interface • RRC recovery kit, hook included. • Fire suppression system ANSUL, 6 nozzles. • SDS Ausminco fire suppression system • Fire extinguisher 6 kg. • Accordance with CE-norms (CEN) • Reverse alarm (CEN). • Emergency steering (CEN). • Boom service support (CEN). • Disassembly needed shaft dim: TBA. • CatBase/LinkOne spare part manuals and additional Instructions, Workshop, Spare part manuals, ToolMan CD’s are available. • Lockable main switch • Rotating beacon (CEN with RRC) • Wiggins fuel fill system • Arctic package (preheater for fuel filter and engine-, hydraulic- and transmission oil)

ISO 9001

ISO 14001

CERTIFICATED FIRM

CERTIFICATED FIRM

Sandvik Mining and Construction Oy Loaders Turku P.O. Box 434 20101 Turku, Finland Tel. +358 205 44 131 Fax +358 205 44 130 e-mail: [email protected] Internet: www.smc.sandvik.com