• Author / Uploaded
• nagtummala

• Categories
• Geometría
• Matemáticas
• Naturaleza

Citation preview

Project : Project no : Item no : Item name : XXXXXXXXXXXXXXXXXXXX Owner ID : XXXXXXXXXXXXXXXXXXXX BUNDLE ENTRANCE AND EXIT AREA CALCULATION Common Parameters :Ds = Shell inside diameter, mm OTL = Outer Tube limit diameter, mm Pt = Tube center to center pitch, mm. Dt = Tube ouside diameter, mm F2 = Factor indicating tube pitch type 0 0 F2 = 1.0 for 90 and 30 type

750 728 25.4 19.05 1

mm mm mm mm

0 F2 = 0.866 for 60 0 F2 = 0.707 for 45

SHELL ENTRANCE AREA CALCULATION :

4.6211 (select from 4.6211, 4.6212, 4.6221, 4.6222) Dn = Nozzle inside diameter, mm. 146.4 mm F1 = Factor indicating presence of impingement plate 0 Shell Entance arrangement Type

RGP-RCP-

F1 = 0 with impingement plate F1 = 1 without impingement plate h=

h1 = h2 =

Average free height above tube bundle or impegment plate, mm. h = 0.5*(h1+h2) for Figures RGP-RCP-4.6211,4.6212,4.6222 h = 0.5*(Ds - OTL) for Figures RGP-RCP-4.6221 Maximum free height (at centerline), mm (measured from drawing) Minimum free height (at nozzle edge), mm h2 = h1-(0.5*(Ds- (Ds^2 - Dn^2)^0.5))

Shell Entance area As =

26.4 mm 26.4 11.0 30 mm 22.8 2 12137 mm

π*Dn*h + (F1*(π/4*Dn2)*((Pt-Dt)/(F2*Pt))

SHELL EXIT AREA CALCULATION : Shell Exit arrangement Type RGP-RCP- 4.6222 (select from 4.6211, 4.6212, 4.6221, 4.6222) Dn = Nozzle inside diameter, mm. 152 mm F1 = Factor indicating presence of impingement plate 0 F1 = 0 with impingement plate F1 = 1 without impingement plate h=

h1 = h2 =

Average free height above tube bundle or impegment plate, mm. h = 0.5*(h1+h2) for Figures RGP-RCP-4.6211,4.6212,4.6222 h = 0.5*(Ds - OTL) for Figures RGP-RCP-4.6221 Maximum free height (at centerline), mm (measured from drawing) Minimum free height (at nozzle edge), mm h2 = h1-(0.5*(Ds- (Ds^2 - Dn^2)^0.5))

Shell Entance area As =

As = π*Dn*h + (F1*(π/4*Dn2)*((Pt-Dt)/(F2*Pt))

26.4 mm 26.4 11.0 30 mm 22.8 2 12604 mm

0.010499

16824.21

rV2 mass flow

658 kg/mS2 22557 kg/hr 6.265833 kg/s 105.014

Project : Project no : Item no : 0 Item name : XXXXXXXXXXXXXXXXXXXX Owner ID : XXXXXXXXXXXXXXXXXXXX BUNDLE ENTRANCE AND EXIT AREA CALCULATION Common Parameters :Ds = Shell inside diameter, mm OTL = Outer Tube limit diameter, mm Pt = Tube center to center pitch, mm. Dt = Tube ouside diameter, mm F2 = Factor indicating tube pitch type 0 0 0 0 F2 = 1.0 for 90 and 30 type, 0.866 for 60 , 0.707 for 45

750 728 25.4 19.05 1

mm mm mm mm

152 624 198 200 2 40000

mm mm

BUNDLE ENTRANCE AREA CALCULATION : Bundle Entance arrangement Type Dn = Nozzle inside diameter, mm. Bs = K= Ip =

RGP-RCP-

4.6231 (select 4.6231 or 4.6241)

Ap =

Baffle Spacing , mm Effective chord distance across bundle, mm (K =Dn for Fig. RGP-RCB-4.6241) Impingement plate diameter or edge length, mm (For no impingement plate = 0) Impingment plate type ( Not Present - 0, Round type - 1, Square type - 2 ) Area of impingement plate, mm 2

a= b= c=

Ap = 0.785* ( Ip)^2 for round type , ( Ip )^2 for square type Dimension from Fig. RGP-RCB-4.6231, mm (measured from the drawing) Dimension from Fig. RGP-RCB-4.6231, mm (measured from the drawing) Dimension from Fig. RGP-RCB-4.6241, mm (measured from the drawing)

Al =

Orintation of baffle cut to nozzle axis ( Normal - 0, Parallel - 1) Unrestricted longitudinal flow area, mm 2 Al = 0 for baffle cut normal to nozzle axis Al = 0.5*a*b for Fig. RGP-RCB-4.6231, 0.5*(Ds-OTL)*c for Fib. RGP-RCB-4.6241

Bundle Entance area Ab = (Bs*(Ds-OTL))+((Bs*K-Ap)*(Pt-Dt)/(F2*Pt))+(Al)

30 50 20 1 750

mm mm

2

mm mm mm mm

2

35366 mm

2

BUNDLE EXIT AREA CALCULATION : Bundle Exit arrangement Type Dn = Nozzle inside diameter, mm.

RGP-RCP-

4.6231 (select 4.6231 or 4.6241)

Bs =

Baffle Spacing , mm

K= Ip = Ap =

Effective chord distance across bundle, mm (K =Dn for Fig. RGP-RCB-4.6241) Impingement plate diameter or edge length, mm (For no impingement plate = 0) Impingment plate type ( Not Present - 0, Round type - 1, Square type - 2 ) Area of impingement plate, mm 2

a= b= c=

Ap = 0.785* ( Ip)^2 for round type , ( Ip )^2 for square type Dimension from Fig. RGP-RCB-4.6231, mm (measured from the drawing) Dimension from Fig. RGP-RCB-4.6231, mm (measured from the drawing) Dimension from Fig. RGP-RCB-4.6241, mm (measured from the drawing)

Al =

Orintation of baffle cut to nozzle axis ( Normal - 0, Parallel - 1) Unrestricted longitudinal flow area, mm 2

198 550 198 200 2 40000 30 30 10 1 450

mm mm mm mm2

mm mm mm mm2

Al = 0 for baffle cut normal to nozzle axis Al = 0.5*a*b for Fig. RGP-RCB-4.6231, 0.5*(Ds-OTL)*c for Fib. RGP-RCB-4.6241 Bundle Exit area Ab =

(Bs*(Ds-OTL))+((Bs*K-Ap)*(Pt-Dt)/(F2*Pt))+(Al)

29775 mm

2