Parts
WC5 PARTS FABRICATION AUTHOR: J. RANDLE © 2005 Randle Design, LLC All rights reserved This section contains a complet
Views 227 Downloads 5 File size 4MB
Recommend stories
- Author / Uploaded
- Carlos Gabriel Estergaard
Citation preview
WC5 PARTS FABRICATION AUTHOR: J. RANDLE
© 2005 Randle Design, LLC All rights reserved
This section contains a complete list of the hardware and fabricated parts required to assemble clock WC5, plus drawings of the individual parts. Also included is a list of suggested sources for all materials. Clock WC5 was designed to be fabricated with as few shop tools as possible. Excluding the wall shelf, the prototype for this clock was built with the following tools: o A basic scroll saw with fine tooth blades and an assortment of scroll sanders. o A drill press with a set of basic twist drills and a set of Forsner bits. o A small belt/disc sander with 400 grit sanding medium. o A turning lathe (useful for grooving rope pulleys but not absolutely necessary) The wall shelf was designed to be fabricated with the tools available in the shop where the prototype was built. Its design can be altered by the builder to use whatever tools are available. Some of the drawings in this section contain all of the dimensions necessary to lay out the subject part. Others, such as the wheel drawings, contain only basic dimensions. It is intended that the under-dimensioned parts be fabricated using cutting patterns as laying them out accurately would be very difficult. Where noted the drawings can be used as cutting patterns if they are printed to scale. Listed below are notes and suggestions pertaining to the fabrication of some of the parts: ARBOR SHAFTS The wooden arbor shafts are all designed to be made from good quality dowel stock. Centering the holes in the ends of the shafts is important. A lathe with a headstock chuck and a tailstock drill chuck would be handy here. Otherwise, you can make a clamp block similar to the one shown below. Carefully align the hole in the block with your drill press chuck, clamp the block in place, and use it as a holder for drilling the shaft end holes.
Typical Shaft Clamp Block PINS The pins are all cut from brass rod. 360 H02 brass is soft and can be easily cut with a hacksaw then finish sanded to length on a disc sander. Drilling a hole to a known depth in the end of a wooden dowel rod then using the rod as a holder for sanding the short pins works well and saves fingers. The ends of the pins can be chamfered while in the holder by holding them against a running sanding belt and spinning them between your fingers. The actual size and angle of the chamfer isn’t critical. A typical holder with pin inserted is shown here. A holder will be needed for each pin diameter.
Typical Pin Holder w/Pin ROPE SHEAVES All of the rope sheaves are designed to be sawn from single pieces of 12mm (15/32”) thick baltic birch plywood and grooved on a lathe faceplate. If no lathe is available the sheaves can be made by cutting three pieces of 3mm (1/8”) thick plywood to the proper diameter then gluing them together. The grooves won’t be tapered but the pulleys should work okay. Of course they will be only 9mm thick making it necessary to shim them with washers at assembly.
2 DIAL A simple way to make the dial shown is: 1.
Apply the full size adhesive backed pattern sections to plywood stock making sure the sections line up properly at the pattern match lines.
2.
Use an xacto knife to carefully cut away the pattern at the numbers and minute marks. Be careful to not cut into the plywood.
3.
Spray the cut out pattern with a good wood sealer. This is important to keep the number paint from soaking into the plywood causing the edges of the numbers to be blurred.
4.
Spray the numbers with a good gloss paint of your color choice. Several thin coats will be necessary to hide the wood grain.
5.
Cut out the dial and sand the cut edges.
6.
Drill and countersink the screw holes. The screw centers are marked on the pattern.
7.
Remove the pattern and clean up any rough edges.
8.
Finish by spraying the entire dial with a good wood sealer.
FRAME POSTS The holes in these posts are to be drilled and tapped with the same taps used for tapping screw holes in metal. Tapping holes in hardwood will provide a strong connection as long as you use coarse thread taps. The necessary tap drills and taps can be bought at a number of places including your local building supply. PENDULUM SUPPORT BRIDGE The upper end of the pendulum suspension spring (pin end) must fit snugly into the slots in this part but not so snug that the spring can’t rotate on its pin. Fit of this part should be checked and adjusted as necessary during fabrication. WHEELS If you look at the drawings closely you will note that the gear teeth on the wheels in the time train of this clock (winding drum to escapement) have an epicycloidal profile on one face and are straight on the other face. The epicycloidal (front) face is the working face and must be cut accurately. The back face does not touch anything and is simply cut away for clearance. Cutting away the unused back face makes the teeth simpler to cut and provides more clearance to compensate for small errors in tooth layout. Because of the difference in the profile of the front and back faces, the gear teeth must be oriented as shown if the clock is to run properly. The wheels not in the time train i.e. WHEEL T-HR, WHEEL T-INT & WHEEL T-6 have epicycloidal faces on both sides of their teeth. The reason is that these wheels run slack (no load), and backlash here will cause the hour hand and second hand to be loose. All of the wheels are drawn as single parts but are actually composites of several pieces of plywood glued together. The recommended procedure for making WHEEL T-1 is: 1.
Apply the furnished wheel pattern to a piece of plywood of the proper thickness.
2.
Drill the center hole with a Forsner bit. A Forsner bit creates a cleaner hole than a twist drill would create. The hole center is clearly marked on the pattern.
3.
Cut out the gear blank along its outside diameter. Do not try to cut the teeth yet.
4.
Center punch the remaining holes marked on the pattern.
5.
Use an xacto knife to carefully cut away the pattern along the profile of each gear tooth. This step may look useless, but if it is skipped all of the drilling, sawing, and sanding around the teeth will cause the pattern to come loose making it difficult to properly finish the part.
6.
Carefully drill a hole at the root of each tooth. You will have to use a twist drill here because Forsner bits that small aren’t available. Accurate location is important here.
3 7.
Drill the five pin holes at the location shown.
8.
Use a scroll saw to rough cut the profile of the teeth.
9.
Use scroll sanders to shape the teeth to the pattern. Don’t quit sanding too soon. Clearance between the gear teeth and the pinion pins is critical.
10. When finished with the teeth, use an xacto knife to carefully make a cut through the pattern around the outside circle shown on the pattern. 11. Remove the pattern inside the cut. 12. Lay the wheel aside and cut a ring from another piece of plywood. The ring dimensions are shown on the drawing. 13. Glue the ring to the wheel using the outer portion of the pattern as a guide. 14. Remove the rest of the pattern. 15. Saw out circular pieces of plywood which can be stacked together to provide a thickness equal to the length of the wheel hub. The diameter of the pieces should be slightly larger than the diameter of the hub. 16. With a Forsner bit drill a hole in the center of each circular piece. The hole should be the same diameter as the hole in the center of the wheel. 17. Sand the pieces to the finished diameter of the wheel hub. This can easily be done on a belt/disc sander by making a jig as shown here; inserting the disc on the jig pin and slowly rotating it as the sander cuts it to size.
18. Glue the hub pieces to the wheel. An excellent way to do this is to drill a hole the same size as the wheel center hole in one jaw of a wooden parallel clamp; insert a piece of dowel rod into the hole from the back; stack the parts to be glued on the rod; close the parallel clamp; and then remove the dowel rod. A typical gluing setup is shown here:
Typical Wheel Gluing Setup
4
19. When the glue is dry, remove the wheel from the clamp, clean up any drips, and spray the entire wheel with a coat of wood sealer. 20. When the sealer is dry, lightly sand the working faces of the gear teeth to remove the wood sealer from them. A clock will not run if sealer or any other finish is allowed to build up on its gear teeth. ANCHOR The shape of the pallets (the tips of the anchor) is arguably the most important feature in the clock. The pallet angles affect the amount of force applied to the pendulum to keep it swinging. Be especially careful to cut them to the proper angle and sand them smooth. Only round the tips enough to remove any burrs. Do not leave any wood sealer on the pallet faces. In fact, putting a single drop of good quality clock oil on each pallet face and allowing it to soak into the wood is a good idea. PENDULUM BOB SHELL The shell of the pendulum bob was designed to be cut as two pieces for convenience. You can glue both patterns to the same piece of wood and cut it as a single piece if you like. PENDULUM BOB SHELL COVERS It is a good idea to cut both shell covers slightly oversize, then sand them to fit the shell after the pendulum bob is assembled. WEIGHT SHELL TOPS The tops of the weight shells were designed as a composite of several pieces. Since thicknesses of plywood can vary slightly, it is a good idea to cut the outside pieces of the composite a bit wider than shown. This will allow you to trim the assembled part to the correct width after gluing. When trimming, be sure to keep the part symmetrical about its center line. Since the top of the small weight shell is made up of only three pieces, and since the gap between the outer pieces needs to be held to the dimension shown, its overall width may vary slightly. You may need to adjust the width of the shell front and back panels and the width of the shell bottom slightly to compensate. WEIGHT SHELL FRONT & BACK PANELS It is a good idea to cut the weight shell front and back panels slightly wider than shown, then to sand them to fit the side panels after gluing. Fabrication of the parts not mentioned above should be obvious from studying the drawings and the notes and suggestions above. If you have questions about any of them feel free to contact the designer at [email protected] for answers.
WC5 CONSOLIDATED PARTS LIST ITEM
PART NO.
DESCRIPTION
MATERIAL
QTY.
SOURCE
1
BLOCK
1/2" W X 3/4" H X 2 5/32" LG
OAK
2
FABRICATE
2
CURVED DISC SPRING
MC # 9716K52
301 STAINLESS STEEL
1
MCMASTER-CARR
3
DOWEL PIN
0.0625 DIA X 1/2" LG
BRASS
1
LOCAL HDWR
4
FLANGED BEARING
MC # 6294K86, 3/16" ID x 5/16" OD x 1/4" LG
MDS-FILLED NYLON
20
MCMASTER-CARR
5
FLANGED BEARING
MC # 6294K89, 3/8" ID X 1/2" OD X 3/8" LG
MDS-FILLED NYLON
2
MCMASTER-CARR
6
FLAT WASHER, SMALL OD
#10 NOM
BRASS
15
LOCAL HDWR
7
FLAT WASHER, SMALL OD
3/8 NOM
BRASS
3
LOCAL HDWR
8
FLAT WASHER, SMALL OD
#4 NOM
BRASS
2
LOCAL HDWR
9
LEAD FILL
MC # 9030K34
#8 LEAD SHOT (9 LBS)
1
MCMASTER-CARR
10
MACHINE SCREW HEX NUT
#8-32UNC
BRASS
4
LOCAL HDWR
11
MACHINE SCREW HEX NUT
#4-40 UNC
BRASS
1
LOCAL HDWR
12
OVAL HD MACHINE SCREW
#8-32 UNC x 1 1/8" LG
BRASS
4
LOCAL HDWR
13
PENDULUM ROD
1/2" DIA X 31" LG
OAK
1
FABRICATE
14
PLUG
3/4" DIA [COMPRESSED] x 1/2" LG
CORK
2
15
ROPE
1/8" DIA X 10'-6" LG (BRAIDED)
NYLON
1
LOCAL HDWR
16
ROUND HD MACHINE SCREW
#10-24 UNC x 1" LG
BRASS
8
LOCAL HDWR
17
ROUND HD MACHINE SCREW
#4-40 UNC x 5/8" LG
BRASS
1
LOCAL HDWR
18
SPLIT PIN
M2 x 12 MM LG
BRASS
1
LOCAL HDWR
19
SPLIT PIN
M2 x 22 MM LG
BRASS
1
LOCAL HDWR
20
SPRING PIN (SLOTTED)
5/64 DIA X 3/4" LG
STAINLESS STEEL
4
MCMASTER-CARR
21
SPRING PIN (SLOTTED)
5/64" DIA X 3/8" LG
STAINLESS STEEL
6
MCMASTER-CARR
22
SUSPENSION SPRING
NORKRO # SS-41
1
NORKRO
23
THREADED ROD
#10-24UNC X 1 3/4" LG
STEEL
4
LOCAL HDWR
24
THUMB NUT
#10-32UNF
BRASS
1
LOCAL HDWR
25
WC5-00-01
SHAFT
OAK
4
FABRICATE
26
WC5-00-02-A
PIN
360 H02 BRASS
1
FABRICATE
27
WC5-00-02-B
PIN
360 H02 BRASS
12
FABRICATE
28
WC5-00-02-C
PIN
360 H02 BRASS
7
FABRICATE
29
WC5-00-02-D
PIN
360 H02 BRASS
1
FABRICATE
30
WC5-00-02-E
PIN
360 H02 BRASS
18
FABRICATE
31
WC5-00-02-F
PIN
360 H02 BRASS
11
FABRICATE
32
WC5-00-02-G
PIN
360 H02 BRASS
12
FABRICATE
33
WC5-00-02-H
PIN
360 H02 BRASS
5
FABRICATE
34
WC5-00-02-J
PIN
360 H02 BRASS
20
FABRICATE
35
WC5-00-02-K
PIN
360 H02 BRASS
3
FABRICATE
36
WC5-00-02-L
PIN
360 H02 BRASS
15
FABRICATE
37
WC5-00-03
ROPE SHEAVE
BALTIC BIRCH PLYWOOD
2
FABRICATE
38
WC5-00-04
SHAFT
360 H02 BRASS
2
FABRICATE
39
WC5-01-01
SHELF
OAK
1
FABRICATE
40
WC5-01-02
BACK PLATE
OAK
1
FABRICATE
41
WC5-01-03
BRACE
OAK
2
FABRICATE
42
WC5-02-01
FRAME PLATE, REAR
BALTIC BIRCH PLYWOOD
1
FABRICATE
43
WC5-02-02
FRAME PLATE, MIDDLE
BALTIC BIRCH PLYWOOD
1
FABRICATE
44
WC5-02-03
FRAME PLATE, FRONT
BALTIC BIRCH PLYWOOD
1
FABRICATE
45
WC5-02-04
DIAL
BALTIC BIRCH PLYWOOD
1
FABRICATE
46
WC5-02-05
FRAME POST
OAK
8
FABRICATE
47
WC5-02-06
DIAL POST
OAK
4
FABRICATE
48
WC5-02-07
PENDULUM SUPPORT BRIDGE
BALTIC BIRCH PLYWOOD
1
FABRICATE
49
WC5-02-08
PIN
360 H02 BRASS
1
FABRICATE
50
WC5-03-01
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
51
WC5-03-02
PIVOT
360 H02 BRASS
1
FABRICATE
52
WC5-03-03-01
CLICK
BALTIC BIRCH PLYWOOD
5
FABRICATE
WC5 CONSOLIDATED PARTS LIST ITEM
PART NO.
DESCRIPTION
MATERIAL
QTY.
SOURCE
53
WC5-03-04
ROPE PULLEY
BALTIC BIRCH PLYWOOD
1
FABRICATE
54
WC5-03-05
ROPE PIN
STAINLESS STEEL
8
FABRICATE
55
WC5-04-01
SHAFT
OAK
1
FABRICATE
56
WC5-04-02
PIVOT (BACK)
360 H02 BRASS
1
FABRICATE
57
WC5-04-03
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
58
WC5-05-01
PIVOT (FRONT)
360 H02 BRASS
1
FABRICATE
59
WC5-05-02
DISC
BALTIC BIRCH PLYWOOD
1
FABRICATE
60
WC5-05-03
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
61
WC5-05-04
HAND (MINUTE)
BALTIC BIRCH PLYWOOD
1
FABRICATE
62
WC5-05-05
HAND (HOUR)
BALTIC BIRCH PLYWOOD
1
FABRICATE
63
WC5-06-01
DISC
BALTIC BIRCH PLYWOOD
1
FABRICATE
64
WC5-06-02
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
65
WC5-07-01
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
66
WC5-08-01
ESCAPE WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
67
WC5-09-01
PIVOT
360 H02 BRASS
1
FABRICATE
68
WC5-09-02
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
69
WC5-09-03
SECOND DISC
BALTIC BIRCH PLYWOOD
1
FABRICATE
70
WC5-10-01
PIVOT
360 H02 BRASS
1
FABRICATE
71
WC5-10-02
WHEEL
BALTIC BIRCH PLYWOOD
1
FABRICATE
72
WC5-11-01
ANCHOR
BALTIC BIRCH PLYWOOD
1
FABRICATE
73
WC5-11-02
IMPULSE LEVER
BALTIC BIRCH PLYWOOD
1
FABRICATE
74
WC5-12-01
LEADER
BALTIC BIRCH PLYWOOD
1
FABRICATE
75
WC5-12-02
BOB GUIDE
OAK
1
FABRICATE
76
WC5-12-03
ADJUSTING ROD
360 H02 BRASS
1
FABRICATE
77
WC5-12-04-01
SHELL HALF
BALTIC BIRCH PLYWOOD
2
FABRICATE
78
WC5-12-04-02
SHELL COVER
BALTIC BIRCH PLYWOOD
2
FABRICATE
79
WC5-13-01
SHELL TOP
BALTIC BIRCH PLYWOOD
1
FABRICATE
80
WC5-13-02-A
FRONT/BACK PANEL
BALTIC BIRCH PLYWOOD
2
FABRICATE
81
WC5-13-02-B
SIDE PANEL
BALTIC BIRCH PLYWOOD
2
FABRICATE
82
WC5-13-03
SHELL BOTTOM
BALTIC BIRCH PLYWOOD
1
FABRICATE
83
WC5-14-01
SHELL TOP
BALTIC BIRCH PLYWOOD
1
FABRICATE
84
WC5-14-02-A
FRONT/BACK PANEL
BALTIC BIRCH PLYWOOD
2
FABRICATE
85
WC5-14-02-B
SIDE PANEL
BALTIC BIRCH PLYWOOD
2
FABRICATE
86
WC5-14-03
SHELL BOTTOM
BALTIC BIRCH PLYWOOD
1
FABRICATE
SUGGESTED MATERIAL SOURCES MATERIAL
VENDOR WEB ADDRESS
VENDOR
Baltic Birch Plywood
Sloan's Woodshop
http://www.sloanswoodshop.com/
Oak Dowel Rod
Local Building Supply
-------
Brass Rod
OnlineMetals.com
http://www.onlinemetals.com/
Clock Parts
Norkro Clock Company, Inc.
http://www.norkro.com/
Miscellaneous Hardware
McMaster-Carr
http://www.mcmaster.com/
Miscellanous Fasteners
Local Hardware Supply
-------
2 1/32"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1
A
3/8"
A
2X
3/16"
1/2"
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
1"
Third angle projection.
SHAFT WOOD CLOCK WC5
Drawing No:
1"
1/32" x 45°
SECTION A-A
WC5-00-01
Sheet 1 of 1
No. Required: 4
Material: OAK "B"
"A"
"C" TYP
ITEM
"A"
"B"
"C"
# REQD
WC5-00-02-A
3/16
1 7/16
1/64
1
W C5-00-02-B
3/16
15/16
1/64
12
WC5-00-02-C
3/16
13/16
1/64
7
WC5-00-02-D
1/8
1/64
1
W C5-00-02-E
1/8
3/4
1/64
18
W C5-00-02-F
1/8
11/16
1/64
11
1
WC5-00-02-G
1/8
41/64
1/64
12
W C5-00-02-H
1/8
17/32
1/64
5
W C5-00-02-J
1/8
15/32
1/64
20
W C5-00-02-K
3/32
3/4
1/64
3
W C5-00-02-L
3/32
17/32
1/64
15
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
PIN WOOD CLOCK WC5 WC5-00-02
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: SEE TABLE
12 15/32" 15°
A 1 7/8"
R1/16" 1 3/8"
3/8"
A SECTION A-A Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
1"
Drawing No:
ROPE SHEAVE WOOD CLOCK WC5 WC5-00-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 2
1 3/8" 1 7/32"
5/64"
3/16"
1/64" X 45° TYP
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
2X
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
5/64" THRU ALL
SHAFT WOOD CLOCK WC5 WC5-00-04
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: 2
9" 4"
1 7/8"
1 1/4"
6 1/4" 2 15/16"
2X
R1/4" TYP
1/2" THRU 2X
1 1/2"
2 7/8"
3/16" THRU
1 1/2"
1/2"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
Material: OAK
SHELF WOOD CLOCK WC5 WC5-01-01
Sheet 1 of 1
No. Required: 1
3 3/4" 1/2"
R1/2" R3"
R1/8" TYP
4"
2X
R1 1/2"
11/64" THRU
1 3/4"
18"
R26 13/64" 15 3/8"
23 1/4"
1/2"
R3/4"
1/2"
3 3/4" 3/16"
9"
1 3/4" R3/4"
10 3/8"
R1 1/2" 4"
R3" R1/2" 3 3/4" Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:4 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
Material: OAK
BACK PLATE WOOD CLOCK WC5 WC5-01-02
Sheet 1 of 1
No. Required: 1
1/2"
5"
R3/4" 2 7/8"
3 1/2" R1 7/8"
R1"
2 7/8"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
Material: OAK
BRACE WOOD CLOCK WC5 WC5-01-03
Sheet 1 of 1
No. Required: 2
5 1/4" REF 4 1/4" 12 15/32"
6 15/64"
3/16"
1" TYP
4X R45 61/64"
13/64" THRU
7/8" R45 61/64"
1"
11 7/32"
7 1/4"
5/8"
2 15/32"
R4"
R1/4" TYP
1 1/2"
R1/2" 7"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
FRAME PLATE, REAR WOOD CLOCK WC5 WC5-02-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
1 1/8"
6 15/64"
1 1/8"
2 59/64"
2 19/64" REF
2 1/4" REF 5X
2 5/8" REF
5/16" THRU
9 27/32"
7 27/32" 7 5/8"
3 1/8"
2 1/8"
1/2" THRU
SEE DRAWING WC5-02-01FOR DIMENSIONS NOT SHOWN
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
FRAME PLATE, MIDDLE WOOD CLOCK WC5 WC5-02-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
6 15/64" 9 23/64" 9 23/64"
5/16" THRU
1/8"
3/4"
1 3/8" 5/64" THRU ALL 3/16" THRU
SECTION A-A
A
A 3/4"
2 1/2"
6 15/64"
7" B.C.
4X 11/64" THRU EQUALLY SPACED ON BOLT CIRCLE
45° SEE DRAWINGS WC5-02-01 & WC5-02-02 FOR DIMENSIONS NOT SHOWN
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
FRAME PLATE, FRONT WOOD CLOCK WC5 WC5-02-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
1/16" 1/16" 1/16"
3 1/8"
1/8" 3/16"
1/2" 3/4"
9/64" TYP
9 1/2"
6 1/2"
7" B.C.
45°
4X
11/64" THRU ALL 21/64" X 82° EQUALLY SPACED ON B.C. 6° TYP 30° TYP
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
DIAL WOOD CLOCK WC5 WC5-02-04
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
2 5/32"
A
5/8"
A
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
2X 5/32" 10-24 UNC
1" 7/8"
SECTION A-A
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
1"
Drawing No:
Material: OAK
FRAME POST WOOD CLOCK WC5 WC5-02-05
Sheet 1 of 1
No. Required: 8
5/8"
1/2"
11/64" THRU
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
Material: OAK
DIAL POST WOOD CLOCK WC5 WC5-02-06
Sheet 1 of 1
No. Required: 4
7/8" 2X
3/16" THRU
7/16"
15/32"
1/32" 2 5/8" REF 1 1/8" 1/32"
3/16"
6 15/64" Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
1/4"
3/8"
6 15/64"
2 5/32"
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
PENDULUM SUPPORT BRIDGE
1"
Third angle projection.
1"
Drawing No:
WOOD CLOCK WC5 WC5-02-07
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
1/16"
R1/16"
13/16"
1/64" X 45° 5/32"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
PIN WOOD CLOCK WC5 WC5-02-08
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: 1
3/4" 5/64" THRU ALL
1/4" 17.60 11/16"
6 15/64" 6 15/64"
5X 1/8" THRU EQUALLY SPACED ON B.C.
3 13/16" 5" 4 1/4" 3/16" 38 TEETH
3 1/4" B.C.
3/8" THRU
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK. Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-1 WOOD CLOCK WC5 WC5-03-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
2 27/32" 43/64" 3/8"
1/64" X 45°
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
3/32" THRU ALL
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
Drawing No:
1"
PIVOT WOOD CLOCK WC5 WC5-03-02
No. Required: 1
Material: 360 H02 BRASS
A
Sheet 1 of 1
A 6 15/64" 9/64" THRU
1/8"
1/8"
1/8"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
SECTION A-A
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
CLICK WOOD CLOCK WC5 WC5-03-03-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 5
15° 1/8" 1/4"
DETAIL A SCALE 2 : 1
12 15/32" 3 1/8" 6 15/64"
3/8" THRU REAM FOR FREE FIT ON PIVOT
6 15/64"
B
3/4"
A
4 1/4"
3 1/8"
B
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
ROPE PULLEY WOOD CLOCK WC5 WC5-03-04
Sheet 1 of 2
Material: BALTIC BIRCH PLYWOOD No. Required: 1
8X
1/16"
1/2"
3 1/8"
45° TYP 2 3/4"
32°
SECTION B-B 2 7/16"
4 1/4"
1 25/32"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK. Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
ROPE PULLEY WOOD CLOCK WC5 WC5-03-04
Sheet 2 of 2
Material: BALTIC BIRCH PLYWOOD No. Required: 1
SR.005 MIN
15/32"
19/32"
1/16"
THIS PART CAN BE MADE BY CUTTING THE HEAD OFF A WIRE BRAD AND ROUNDING ITS TIP Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
Drawing No:
1"
ROPE PIN WOOD CLOCK WC5 WC5-03-05
Sheet 1 of 1
No. Required: 8
Material: STAINLESS STEEL
5/64" THRU
1/32" X 45° TYP
1 9/32"
2 1/32" 3/8"
1/4"
1/4"
2X 3/16"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
5/64" THRU ALL 3/16"
5/8"
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
Material: OAK
1/2"
SHAFT WOOD CLOCK WC5 WC5-04-01
Sheet 1 of 1
No. Required: 1
13/16" 1/4" 3/16"
1/64" X 45° TYP
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
3/32" THRU ALL
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
1"
PIVOT (BACK) WOOD CLOCK WC5
Drawing No:
WC5-04-02
Sheet 1 of 1
No. Required: 1
Material: 360 H02 BRASS
2 3/16" 2 1/64" 1 3/32" 3/8" 3/16"
3/32" THRU ALL
5/64" THRU ALL
1/64" X 45° TYP
3/32" THRU ALL
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
PIVOT (FRONT) WOOD CLOCK WC5 WC5-05-01
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: 1
6 15/64"
A
6 15/64"
1/8" 54 TEETH
12 15/32" 12X 3/16" THRU EQUALLY SPACED ON B.C.
R1/8"
1"
3/8"
2"
1"
GLUE LINES
4 43/64"
A
SECTION A-A
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-2 WOOD CLOCK WC5 WC5-04-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
6 15/64" 6 15/64"
1 1/2"
1/8"
3/16" THRU
3/4"
1 1/4" HOLE CIRCLE 3/32" THRU ALL
15 X 1/8" THRU EQUALLY SPACED ON H.C. THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK. Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
1"
Drawing No:
DISC WOOD CLOCK WC5 WC5-05-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
9X
9 23/64"
1/8" THRU
1"
3/8" THRU
3/4" H.C.
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
DISC WOOD CLOCK WC5 WC5-06-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8" 3 1/8"
9/64" 48 TEETH
R1/8"
3/4"
5/16"
4 11/64"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 0912/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-HR WOOD CLOCK WC5 WC5-05-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8" 3 1/8"
4 7/16"
3/16" THRU
GLUE LINE
3/4"
3/32" THRU ALL
1/8" TO HOLE CENTER THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
HAND (MINUTE) WOOD CLOCK WC5 WC5-05-04
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8"
3 3/16"
5/16" THRU
3/4"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
HAND (HOUR) WOOD CLOCK WC5 WC5-05-05
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8" 6 15/64"
1/8" 45 TEETH
R1/8"
1" 3/8"
3 59/64"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-3 WOOD CLOCK WC5 WC5-06-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8" 6 15/64"
1/8" 44 TEETH 9X
1/8" THRU
R1/8"
1"
3 53/64"
3/8" THRU
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-4 WOOD CLOCK WC5 WC5-07-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
6 15/64"
3 1/8"
R1/8" 15 X 3/32" THRU EQUALLY SPACED ON H.C. 2 3/8" HOLE CIRCLE 59/64" HOLE CIRCLE
1 3/16"
11 X 1/8" THRU EQUALLY SPACED ON H.C.
2 5/8"
3/8" THRU THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
ESCAPE WHEEL WOOD CLOCK WC5 WC5-08-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
1 27/32" 17/64"
1 5/16"
3/16"
1/64" X 45° TYP
5/64" THRU ALL 3/32" THRU ALL
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
1"
PIVOT WOOD CLOCK WC5
Drawing No:
WC5-09-01
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: 1
5/64" THRU ALL 1" 1 9/64"
5/64" 3/16"
5/64" THRU ALL
1/64" X 45° TYP
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
PIVOT WOOD CLOCK WC5 WC5-10-01
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: 1
3 1/8" 6 15/64" 9/64" 22 TEETH
1/8"
2"
3/4"
3/16" THRU
5/64" THRU ALL THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-6 WOOD CLOCK WC5 WC5-09-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8" 6 15/64"
3/64"
1/8"
1"
3/4" 3/8"
2 1/4"
3/16"
1/64" X 45° TYP
3/32"
3/32" THRU ALL THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
SECOND DISC WOOD CLOCK WC5 WC5-09-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3 1/8" 6 15/64"
9/64" 45 TEETH
12 X
1/8" THRU
R1/8"
1 1/4"
3 59/64"
5/16" THRU THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
WHEEL T-INT WOOD CLOCK WC5 WC5-10-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3/8" THRU
3/4"
GLUE LINE
1/8" TYP
R1/64" MAX
5.99 15/64" 3 1/8"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
ANCHOR WOOD CLOCK WC5 WC5-11-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
6 15/64"
1/32" 1/2" 3/16" THRU
3/8"
1 1/2"
1/8" 2"
GLUE LINE 45°
1/8" THRU
3/16"
5 1/2"
3/8"
1/8" THRU 6 15/64"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
IMPULSE LEVER WOOD CLOCK WC5 WC5-11-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
1/2"
6 15/64" TYP
1/32"
1/4"
6 15/64"
1/16" THRU ALL
9/16" 1 1/2" 45° TYP
GLUE LINES 3/16" TYP 5 1/2"
9"
1/8"
1"
1/4"
R1/2" TYP 30° TYP
1 1/2"
1 3/4"
1 1/8"
1/2" Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 2:3 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
LEADER WOOD CLOCK WC5 WC5-12-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
1/2"
1 1/2"
3 3/4"
1/2"
5/64" THRU ALL 3/16"
1/16" X 45° TYP
5/8"
11/16"
3/4"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
Material: OAK
BOB GUIDE WOOD CLOCK WC5 WC5-12-02
Sheet 1 of 1
No. Required: 1
3/16"
1/8"
3/32" THRU ALL
3 1/2"
2 1/2" #10-32 UNF
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
ADJUSTING ROD WOOD CLOCK WC5 WC5-12-03
Material: 360 H02 BRASS
Sheet 1 of 1
No. Required: 1
R1/8"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
18 45/64"
SHELL HALF WOOD CLOCK WC5 WC5-12-04-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 2
3"
R3 39/64" REF
R1 1/2" 4 1/4"
R3 39/64" REF
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
3 1/8"
SHELL COVER WOOD CLOCK WC5 WC5-12-04-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 2
37/64" 6 15/64"
6 15/64"
15/32" REF R3/8"
15/32" REF
3/16"
7/8"
1 15/32"
12 15/32"
GLUE LINE TYP 2"
2"
THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
SHELL TOP WOOD CLOCK WC5 WC5-13-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
10"
3 1/8"
"A"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
ITEM
DESCRIPTION
"A"
# REQD
WC5-13-02-A
FRONT/BACK PANEL
2 15/64
2
WC5-13-02-B
SIDE PANEL
2
2
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
SHELL SIDES WOOD CLOCK WC5 WC5-13-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: SEE TABLE
3/4" THRU
2"
2"
12 15/32"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
1"
Third angle projection.
Drawing No:
1"
SHELL BOTTOM WOOD CLOCK WC5 WC5-13-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
3/4" THRU
1 1/16"
1 1/16"
12 15/32"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
SHELL BOTTOM WOOD CLOCK WC5 WC5-14-03
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
19/32" 6 15/64" R3/8"
6 15/64"
3/16"
7/8"
1 15/32"
12 15/32"
GLUE LINE TYP
1 1/16"
1 1/16" THIS DRAWING VIEW CAN BE USED AS A CUTTING PATTERN WHEN PRINTED TO SCALE. TO VERIFY THAT THE PRINTOUT IS TO SCALE CHECK THE DIMENSIONS OF THE BOX IN THE TITLE BLOCK.
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:1 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
SHELL TOP WOOD CLOCK WC5 WC5-14-01
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: 1
5"
3 1/8"
"A"
Drawn By: J. RANDLE Drawn Date: 09/12/05 Drawing Scale: 1:2 PROPRIETARY AND CONFIDENTIAL The information contained in this drawing is the sole property of RANDLE DESIGN, LLC. Any reproduction in part or as a whole without the written permission of RANDLE DESIGN, LLC is prohibited.
ITEM
DESCRIPTION
"A"
# REQD
WC5-14-02-A
FRONT/BACK PANEL
1 19/64
2
WC5-14-02-B
SIDE PANEL
1 1/16
2
All dimensions are in inches Tolerance +/-.005" typical.
Description:
OK to scale drawing only if box to right is full scale.
Project:
Third angle projection.
1" 1"
Drawing No:
SHELL SIDES WOOD CLOCK WC5 WC5-14-02
Sheet 1 of 1
Material: BALTIC BIRCH PLYWOOD No. Required: SEE TABLE