Published BS and BS ISO Standards coming under the responsibility of BS committee MCE/5 Gears Title Latest pub. date
Views 156 Downloads 0 File size 834KB
Published BS and BS ISO Standards coming under the responsibility of BS committee MCE/5 Gears
Title
Latest pub. date
BS 2007:1975
Specification for circular gear shaving cutters, 1 to 8 metric module, accuracy requirements
1975.10.31
BS 2059/1:1957
Summary sheet: straight sided splines. Bottom fitting. 1957.08.15 Shallow
BS 2059/2:1957
Summary sheet: straight sided splines. Bottom fitting. 1957.08.15 Deep
BS 2059/3:1957
Summary sheet: straight sided serrations. Internal and 1957.08.15 external
BS 2059:1953
Specification for straight-sided splines and serrations
BS 2062-1:1959
Specification for gear hobs. Hobs for general purposes, 1959.12.18 1 d.p. to 20 d.p. inclusive
BS 2062-2:1960
Specification for gear hobs. Hobs for gears for turbine 1960.12.23 reduction and similar drives
BS 2518-1:1954
Specification for rotary form relieved gear cutters. Diametral pitch
1954.11.09
BS 2518-2:1977
Specification for rotary form relieved gear cutters. Metric module
1977.04.29
Glossary for gears. Notation
1976.11.30
Number
BS 2519-2:1976 (ISO 701:1976)
1953.12.31
BS 2697:1976
Specification for rack type gear cutters, metric module 1976.07.30
BS 3170:1972
Specification for flexible couplings for power transmission
BS 4235-1:1972
Specification for metric keys and keyways. Parallel and 1972.02.22 taper keys
1972.03.30
BS 4235-2:1977 (ISO 3912-1977)
Specification for metric keys and keyways. Woodruff keys and keyways
1977.10.31
BS 436-5:1997 (ISO 1328-2:1997)
Spur and helical gears. Definitions and allowable values of deviations relevant to radial composite deviations and runout information
1997.10.15
12 June 2014
Published BS and BS ISO Standards coming under the responsibility of BS committee MCE/5 Gears
BS 4506:1970
Specification for shaft ends
1970.01.19
BS 4582-1:1970
Specification for fine pitch gears (metric module). Involute spur and helical gears
1970.03.27
BS 4582-2:1978
Specification for fine pitch gears (metric module). Hobs and cutters
1978.10.31
BS 4823:1972
Guide to the selection of fitment bores for cylindrical shaft ends
1972.07.31
BS 5186:1975
Specification for shaft centre heights
1975.02.28
BS 5246:1976
Specification for pinion type cutters for spur gears - 1 to 8 metric module
1976.02.27
Specification for straight-sided splines for cylindrical BS 5686:1986 (ISO 14shafts: metric nominal dimensions, tolerances and 1982) gauging requirements BS 6168:1987
Specification for non-metallic spur gears
BS 6186-1:Addendum No. 1:1993 (ISO Specification for straight cylindrical involute splines: 4156:1981/Amendment metric module, side fit. Inspection 1:1992) BS 6613:1985 (ISO 4863-1984)
1986.08.29
1987.03.31
1993.03.15
Methods for specifying characteristics of resilient shaft 1985.07.31 couplings
BS 6710:1987
Specification for dimensions of chain wheel tooth forming tools
1987.02.27
BS 721-1:1963
Specification for worm gearing. Imperial units
1963.04.25
BS 721-2:1983
Specification for worm gearing. Metric units
1983.09.30
BS 7676-2:1993 (ISO 8579-2:1993)
Acceptance code for gears. Determination of mechanical vibrations of gear units during acceptance 1993.08.15 testing
BS 7848:1996 (ISO 10825:1995)
Gears. Wear and damage to gear teeth. Terminology
1996.02.15
BS 7862:1996 (ISO 14104:1995)
Gears. Surface temper etch inspection after grinding
1996.06.15
12 June 2014
Published BS and BS ISO Standards coming under the responsibility of BS committee MCE/5 Gears
BS 978-1:1968
Specification for fine pitch gears. Involute spur and helical gears
1968.01.31
BS 978-2:1952
Specification for fine pitch gears. Cycloidal type gears
1952.01.24
Gears for instruments and clockwork mechanisms. Cycloidal type gears. Double circular arc type gears
1959.05.15
BS 978-3:1952
Specification for fine pitch gears. Bevel gears
1952.01.24
BS EN ISO 13691:2002
Petroleum and natural gas industries. High-speed special-purpose gear units
2003.03.24
BS ISO 1122-1:1998
Vocabulary of gear terms. Definitions related to geometry
2010.10.31
BS ISO 14635-1:2000
Gears. FZG test procedures. FZG test method A/8, 3/90 2000.08.15 for relative scruffing load-carrying capacity of oils
BS ISO 14635-3:2005
Gears. FZG test procedures. FZG test method A/2, 8/50 for relative scuffing load-carrying capacity and wear 2006.01.17 characteristics of semifluid gear greases
BS ISO 21771:2007
Gears. Cylindrical involute gears and gear pairs. Concepts and geometry
2007.09.28
BS ISO 23509:2006
Bevel and hypoid gear geometry
2006.10.31
BS ISO 2490:2007
Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module. Nominal dimensions
2007.12.31
BS ISO 4156-1:2005
Straight cylindrical involute splines. Metric module, side fit. Generalities
2006.01.20
BS ISO 4156-2:2005
Straight cylindrical involute splines. Metric module, side fit. Dimensions
2006.01.19
BS ISO 4156-3:2005
Straight cylindrical involute splines. Metric module, side fit. Inspection
2006.01.23
BS ISO 4468:2009
Gear hobs. Accuracy requirements
2010.01.31
BS ISO 53:1998
Cylindrical gears for general and heavy engineering. Standard basic rack tooth profile
1998.10.15
BS ISO 54:1996
Cylindrical gears for general engineering and for heavy 1997.04.15 engineering. Modules
BS 978-2:Addendum No. 1:1959
12 June 2014
Published BS and BS ISO Standards coming under the responsibility of BS committee MCE/5 Gears
BS ISO 6336-1:2006
Calculation of load capacity of spur and helical gears. Basic principles, introduction and general influence factors
2008.09.30
BS ISO 6336-2:2006
Calculation of load capacity of spur and helical gears. Calculation of surface durability (pitting)
2008.09.30
BS ISO 6336-3:2006
Calculation of load capacity of spur and helical gears. Calculation of tooth bending strength
2008.09.30
BS ISO 6336-5:2003
Calculation of load capacity of spur and helical gears. Strength and quality of materials
2003.07.04
BS ISO 6336-6:2006
Calculation of load capacity of spur and helical gears. Calculation of service life under variable load
2007.09.28
BS ISO 701:1998
International gear notation. Symbols for geometrical data
1999.10.15
BS ISO 8579-1:2002
Acceptance code for gear units. Test code for airborne 2002.08.30 sound
BS ISO 9083:2001
Calculation of load capacity of spur and helical gears. Application to marine gears
2001.09.21
BS ISO 9085:2002
Calculation of load capacity of spur and helical gears. Application for industrial gears
2002.03.25
BS ISO TR 100641:1992
Code of inspection practice. Inspection of corresponding flanks of gear teeth
2006.11.30
BS ISO TR 100642:1996
Code of inspection practice. Inspection related to radial composite deviations, runout, tooth thickness and backlash
2006.12.29
BS ISO TR 100643:1996
Code of inspection practice. Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
2006.11.30
Cylindrical gears. Calculation of service life under BS ISO TR 10495:1997 variable load. Conditions for cylindrical gears in accordance with ISO 6336
1998.05.15
BS ISO TR 10828:1997 Worm gears. Geometry of worm profiles
1998.05.15
BS ISO/TR 100644:1998
12 June 2014
Code of inspection practice. Recommendations relative to surface texture and tooth contact pattern
2006.11.30
Published BS and BS ISO Standards coming under the responsibility of BS committee MCE/5 Gears
checking BS ISO/TR 139891:2000
Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears. Flash temperature method
BS ISO/TR 139892:2000
Calculation of scuffing load capacity of cylindrical, 2001.05.15 bevel and hypoid gears. Integral temperature method
BS ISO/TR 141791:2001
Gears. Thermal capacity. Rating gear drives with thermal equilibrium at 95$0DC sump temperature
2001.09.25
BS ISO/TR 141792:2001
Gears. Thermal capacity. Thermal load carrying capacity
2001.09.21
PD 6457:1970 PD ISO/TR 100645:2005
2001.05.15
Guide to the application of addendum modification to 1970.11.17 involute spur and helical gears Code of inspection practice. Recommendations relative to evaluation of gear measuring instruments
2006.11.30
PD ISO/TR 14521:2010 Gears. Calculation of load capacity of wormgears
2011.02.28
PD ISO/TR 18792:2008 Lubrication of industrial gear drives
2009.02.28
harrya Thursday, 2014/06/12
12 June 2014