• Author / Uploaded
• Aldemar Alonso

Citation preview

30/3/2019

C18 Generator Set N1D00001-UP(SEBP5558 - 19) - Systems & Components

Previous Screen

Welcome: r460oaa Product: GENERATOR SET Model: C18 GENERATOR SET N1D Configuration: C18 Generator Set N1D00001-UP

Testing and Adjusting C13, C15, and C18 Generator Set Engines Media Number -SENR9708-24

Publication Date -01/04/2015

Date Updated -08/08/2018 i07462518

Electronic Unit Injector - Adjust SMCS - 1290-025

MEUI A Injector Overview

Illustration 1

g03882525

Typical MEUI A injector (1) Solenoid prongs (2) Top of injector (3) Height adjustment tool ledge

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 1/4

30/3/2019

C18 Generator Set N1D00001-UP(SEBP5558 - 19) - Systems & Components

Mechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1. The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height adjustment tool (3).

MEUI A Injector Adjustment Table 1 Required Tools Part Number

Part Name

Quantity

9U-7227

Injector Height Gauge

1

Illustration 2

g01332476

Injector Mechanism (Typical example) (1) Rocker arm (2) Adjusting screw (3) Locknut (4) 9U-7227 Injector Height Gauge

To adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure: 1. Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". 2. Injector height gauge (4) is used to obtain a dimension of 78.0 ± 0.2 mm (3.07 ± 0.01 inch). The dimension is measured from the top of the unit injector to the machined ledge of the fuel injector body. a. Set the injector height tool body on top of the injector tappet body. The rod of the height adjustment tool should sit on the machined ledge of the injector body. 3. Turn unit injector adjusting screw (2) clockwise until the correct height is obtained. Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be flush with the injector height tool body. https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 2/4

30/3/2019

C18 Generator Set N1D00001-UP(SEBP5558 - 19) - Systems & Components

4. Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 ± 10 N·m (74 ± 7 lb ft). 5. To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360 degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on the exhaust stroke. 6. Repeat Steps 3 through 4. 7. Remove the timing bolt from the flywheel after all the unit injector adjustments have been made. Reinstall the valve mechanism cover.

MEUI C Injector Overview

Illustration 3

g03882544

Typical MEUI C injector (1) Tappet (2) Electrical connector

Mechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3. The injectors typically have a raised tappet (1), and electrical connector (2).

MEUI C Injector Adjustment 1. Set the engine to Top Dead Center (TDC) for number 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston". 2. Set injectors 3, 5, and 6 using the procedure that follows. https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 3/4

30/3/2019

C18 Generator Set N1D00001-UP(SEBP5558 - 19) - Systems & Components

a. Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector. b. Turn the adjustment screw an additional 180 degrees clockwise. c. Hold the adjustment screw and torque the nut to 55 ± 10 N·m (41 ± 7 lb ft). 3. To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel. a. Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector. b. Turn the adjustment screw an additional 180 degrees clockwise. c. Hold the adjustment screw and torque the nut to 55 ± 10 N·m (41 ± 7 lb ft). Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees.

Sat Mar 30 2019 11:45:57 GMT-0500 (hora estándar de Colombia) r460oaa

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage… 4/4