• Author / Uploaded
• Waseem Tariq

Citation preview

Inhoudsopgave error messages 4008 Error messages after turning power on

blz 1

Bios Test passed ROM Test passed RAM Test passed

blz 1

FXX Configuration EPROM ERROR BRAM_#_XXXX_XXXX_XXXX RAM ERROR Keyboard Error Watchdog Error XX (not calibrated) NTC109 switched off Error description: T1 test F XX Bypass F XX Opt. Detector F XX Bloodsystem F XX Venous F XX Airdetector F XX Display F XX Arterial F XX Accumulator F XX Bloodleak F XX Temperature F XX Neg. Pressure F XX Pos. Pressure F XX UF function F XX Conductivity F XX Diasafe F XX HDF Filter F XX Online plus / diasafe plus / HPU Error messages during dialysis Voltage Failure 24 V Switched Off CPU-II failed Profile time diff. Cyclical PHT FXX V84 faultiness ! Shunt Cover open Voltage Failure UF1 volume Error UF2 volume – Error FXXX UF-failure Error Messages on 4008 Display HPU Error FXX Configuration Warnings / Information 24 V Switched Off Air in system ASP failure BLD dimness warning Connect Cone Line

blz 2 t/m 27 blz 2 blz 3 blz 4 t/m 5 blz 6 blz 7 t/m 8 blz 9 blz 10 blz 11 blz 12 blz 13 blz 14 blz 15 t/m 17 blz 18 t/m 19 blz 20 blz 21 blz 22 t/m 23 blz 24 t/m 27 blz 28 t/m 30 blz 28

blz 29

blz 29 t/m 30 blz 31 t/m 33 blz 31 t/m 32 blz 33 blz 34 t/m 35 blz 34

A

CPU II failed Cyclic PHT FXX Dialines not conn Dialyzer failure Fillprogram Fill-time reached Flow off warning Fund. Not allowed F XXX UF failure Hep pomp alarm Hep pomp not on Increase blood flow Maxium filling time reached Module error No UF Profiles paused Profile time diff Relation BPR/UFR Set UF rate Shunt cover open Timer alarm Timer stops UF rate UF goal reached V84 faultiness Ven con. Test failed Voltage failure Wrong cone. Supply

Description of machine errors during the cleaning programs. V84 monitoring

blz 34

blz 35

blz 36

Rinse failure F XX PSW (pressure switch) monitoring

blz 37 t/m 38

Rinse failure F XX Hydraulics test (check of V91,V99,V100) In machines with central delivery system

blz 39

Rinse failure F11 V91/V100 Failure V99 Failure V130 Failure V188 Failure CDS Failure V104 CDS Failure V102 F14 Hydraulics test (check of V91,V99,V100) In machines without central delivery system F14 V91 Failure F14

B

blz 40

Hydraulics test (check of V91,V99,V100,V130) In machines with BIBAG and without central delivery system Rinse failure F15 V91 Failure V100 Failure Rinse failure F16 V99 Failure Rinse failure F17 V130 Failure Rinse failure F20 V188 Failure Rinse failure F14 V39 test

blz 41 t/m 42

blz 42

blz 43

V39 Failure Further messages which may be displayed before or during a cleaning program. Accumulator empty Blood Sensed by OD Bibag connect open Bic line not conn Bypass valve failed CDS connectors open CDS failure V145/147 Conc line not conn Connect CDS lines Connect desinfectant CPU-II failed Dialines not conn Dial. Valve failed Desinfectant empty? Desinf-temp too high Float-switch failure Flow alarm HDF-pomp failure Heater error High temperature Low temperature No LD alarm Pleace Wait Power failure Press CONFIRM key Remove CDS lines Rinse after desinf. Rinse required Shunt cover open UF-pomp failed UF-pomp 2 failed Upper flow alarm V102 failure V104 failure Voltage Failure Water alarm

blz 44 t/m 46

blz 45

blz 46

C

Bloedpomp foutmeldingen /stroke versie 1.30

blz 47

E XX Strookvolume afhankelijke omschakelpunten Error Messages ONLINE plus Module

blz 48

Watchdog error no. XX Program error no. XX Communication error no. XX Valve error no. XX T1-test error no. XX Ref. voltage error no. 11 CRC error no. 12 EEPROM error no. 13 From monitor error no. 14 Error Messages During the Functional Test of the BVM Software error x System error x Treatment error: door opend Error Messages and Warnings Displayed by the BVM 4008 During Preparation and Treatment. BV- control off XX BVM not calibrated Cuvette unsuitable Door open No Blood No calibration No communication No saline solution Service mode Error Messages and Warnings Displayed by the Dialysis System During Preparation and Treatment. BVM error BVM bpr too low BVM enter critRBV BVM Failure XX BVM not calibrated BVM not possible BVM not Ready BVM only ISO-time BVM pArt too low BVM uf –control? BVM UF- goal? BVM + ISO t = …. Dialysis with BVM First start UF H(D)F with BVM HDF with BVM HF with BVM Module error No blood in system SN- HDF with BVM

D

blz 49 t/m 50 blz 49 blz 50 blz 51 t/m 44

blz 52

blz 53 t/m 47

blz 54

SN- HF with BVM SN with BVM Stop UF- profile UF- control aborted UFR limit Wrong UF- param. 4008 HDF with BVM 4008 HF with BVM ERROR Messages BPM

blz 55

blz 56 t/m 58

E XXXX Handeling of Error Messages of the BTM

blz 59 t/m 66

E