• Author / Uploaded
• Magno Sousa Nogueira

Citation preview

MPT-HC

9500 MPR Quick Start Guide MPT-HC Overview and ODU-to-IDU MPT through power injector MPT to MSS MPT to MSS MPT to Ethernet device MPT to core board or Ethernet Connections plug-in Electrical (100 m)

Configuration [1+0]

Electrical (100 m)

[1+1] MPT to MSS Electrical (100 m)

[2+0] MPT-HC with XPIC-RPS module Optical RPS port XPIC port

XPIC-RPS module

[2+0] XPIC MPT to MSS Electrical (100 m)

OrthoMode Transducer OMT 6, 7, and 8 GHz

MPT pol V Jumper RJ45/N

MPT pol H MPT pol H XPIC cable

Maintenance port Note: In 2+0 configurations, you must inter-connect the two MPT-HCs using a preassembled RPS optical jumper and two optical SFP modules (different lengths are available).

MSS-4/8 Note: See the applicable MPR user manual for other supported configurations.

MPT pol V

CAT5e cable data and DC 1AC015760006

Optical user port

MSS-4/8 Note: See the applicable MPR user manual for other supported configurations.

MSS-4/8 Note: See the applicable MPR user manual for other supported configurations.

c a Fiber t 7 e

XPIC cable Coaxial cable

X MSS-4/8 MSS-4/8 P I See the applicable MPR user manual Note: C supported configurations. for other

Coupler 11 to 38 GHz

OrthoMode Transducer OMT 11 to 38 GHz

9500 MPR Quick Start Guide 3.1 Put silicone grease on the O-ring (mandatory) before inserting the MPT; see the following figure.

5

Set MPT polarization

4.1 Factory delivery is in V polarization. To change the polarization, loosen the two screws and line up the H or V polarization with the polarization references.

5.2 Secure the module with the four hooks on the corresponding brackets.

6.2 Install the MPT [2+0] with the OMT.

2.2 Verify the polarization on the antenna nose and change it if required. Vertical

WARNING: Verify that the indication engraved on the coupler is directed toward the pole side.

Horizontal

H

Note: MPT [1+1] configuration is always in horizontal polarization; this setting does not determine the link polarization.

H

Reference polarization

3.2 Remove the solar shield from the MPT by unscrewing the screws. 3.3 Set the appropriate polarization on the MPT (see step 4); the connectors must face down. 3.4 Open the four locking hooks on the MPT walls and slide the MPT on the antenna nose adapter.

WARNING: To avoid equipment damage, do not remove the waterproof tape that is glued on the MPT waveguide.

3.5 Secure the MPT module with the four hooks.

Example MPT-HC installation

Ground the MPT

2.2 7.1 Connect the MPT grounding connector to the nearest grounding plate, using the ground cable 16mm² 1AC001060084.

3.1

For an explanation, see the step indicated by the numbered circle.

Example 11 to 38 Ghz coupler

8

Auto-amalgamating tape is recommended.

Note: This is a guideline for assembling the R2CT with the RJ45 connector for CAT5e cable. For details see Best practice and tips MPR R2CT and RJ45 connector and grounding 3FQ 24013 1100 PCZZA.

R2CT connector 1AB150990002

5 4

2.1

Connection to the ground plate

9.1 Use optical LC-LC preassembled cable 3CC52170xxxx for MPT optical connections. Optical LC-LC preassembled cable is available in different lengths to interconnect MPT to MSS.

RJ45 connector 1AB074610027

XPIC-RPS cable

10

RJ45 hirose tool 1AD160490001 or

supplier ref:

RJ45 connector

8.3 Hoist the cable using the buckle on the R2CT cap. 8.4 Connect the assembled R2CT to the MPT, mount another RJ45 plug indoors, and verify all cables and connectors using a cable tester (to avoid short circuit and verify continuity).

11

Perform alignment

10.1 Plug the connector on the maintenance port on the MPT; see (A).

Remove MPT [1+1] solar shield

11.1 For MPT 1+1 configuration with pole mounting on the left side (only with 3CC10752AAAA), remove the pre-cut part for freq bands from 11 to 38 GHz.

10.2 Plug the banana plugs into the multi-meter to align the antenna; see (B).

9.2 Use coaxial cable with N-to-Ethernet pairs pigtails on each side (plus RJ45 and R2CT connectors) for MPT power.

Cat5e cable 1AB150990002

HT601/TM21-88P

Electrical CAT5e

11

Assembled R2CT connector

8.2 Mount the RJ45 connector using the RJ45 hirose tool.

8

10

Assemble and connect electrical connectors

8.1 Prepare the R2CT connector, insert the CAT5e cable, and insert the RJ45 plug unlocking clip.

– Kit for Ethernet cable or coaxial cable (Ø 6,85) 1AD040130004 – Kit for coaxial cable (Ø 10,3) 1AB128500002

Connect optical cables

Install MPT [2+0] with OMT

2.1 Install the integrated antenna mounting kit.

1.4 Install the integrated DDF; see the applicable manual (75 Ω, 120 Ω, RJ45).

9

6

6.1 Follow the same process described in steps 3 and 4: Install and Set MPT polarization) and then connect.

1.3 Connect the power supply cable between the MSS and breakers or power panel: – MSS1-c and power injector box: 2x1 mm² 1AC007800068 – MSS4/8: 2x4 mm² 3DB18271AAXX – MSS8 (full configuration): 2x6 mm² 3CC52190AAXX

Washer screw and terminal plug are provided with the MPT.

Install RF coupler for MPT [1+1]

5.1 Set the coupler polarization (antenna side) to match the antenna polarization (same process as steps 3 and 4: Install and Set MPT polarization), and then connect.

Note: Two pole mounting installation kits are available: integrated antenna and non-Integrated antenna. This procedure describes the antenna mount only.

1.2 Ground the MSS using the ground screw on the front panel of the bracket on the right side of the MSS; use grounding kit 3CC13423AAXX.

7

4

Install MPT [1+0]

H V

1.1 Install the MSS indoor unit in one of three supported configurations (see the applicable user manual): – ETSI rack (21 in.) – standard rack (19 in.) – wall mount

3

Install outdoor unit

V

Note: MPT toolbox is mandatory 3CC50098AAXX.

2

V

Install MSS indoor unit

H

1

MPT-HC Installation Steps

Contact support 1 Contact Support To access online customer support (OLCS), go to: http://alcatel-lucent.com/support/ supportredirect.html

1.1

1.3

For product documentation:

Light Service Kit for Alignment 3CC52191AAXX

On the OLCS page, select Sign In/Register (MyAccess) and then log in to OLCS.

Measurement Service kit cable VDC: 5 4.71 4.12 3.5 2.9 2.3 1.71 1.11 0.59 0.14 RSL (dBm) : -10 -20 -30 -40 -50 -60 -70 -80 -90 -100

For technical support contact information:

10.3 Adjust the site elevation to the tracking path (line A-A) and adjust the azimuth to the maximum RSL (lobe number 2).

1.2

1.4 Line A-A represents azimuth tracking path of a properly aligned antenna.

All Rights Reserved © Alcatel-Lucent 2011

11.2 For MPT 1+1 configuration with pole mounting on the right side (only with 3CC10752AAAA), remove the pre-cut part for freq bands from 11 to 38 GHz.

On the right side of the OLCS page under Product Technical Support, select your country from the Phone and Email Contact Information drop-down list. The contact information is displayed.

REF: 3DB20024BAAA ICS 01