• Author / Uploaded
• ericka

Citation preview

SANDVIK CONE CRUSHER CH430 Technical data

Weights, dimensions, data DIMENSIONS A B C D E F G H I J

(mm) 1 360 820 392 660 710 1 675 1 060 1 680 1 690 1 270

(Inch) 54 32 15 26 28 66 42 66 67 50

WEIGHTS Feed hopper Spider cap Topshell, complete F crushing chamber Mainshaft assembly, complete Eccentric, complete Bottomshell assembly, complete Pinionshaft assembly, complete Oil tank Total weight, F crushing chamber

(kg) 230 130 2 900 1 840 410 3 920 250 270 9 200

(lbs) 506 286 6 380 4 048 902 8 624 550 594 20 240

RECOMMENDED DRIVE Max motor power, EC crushing chamber Motor type, recommended Eccentric speed Pinion shaft speed

132 kW 200HP Squirrel-cage 360 rpm 1 475 rpm

S A N D V I K M I N I N G A N D C O N S T R U C T I O N, T E L. +4 6 4 0 4 0 6 8 0 0, F A X +4 6 4 0 4 0 6 8 9 8 www.sandvik.com The above information is a general description only, is not guaranteed and contains no warranties of any kind

SANDVIK CONE CRUSHER CH430 Technical data Capacities Performance figures are approximate and give an indication of what the crusher can produce. They apply for open circuit crushing of dry material with a bulk density of 1600 kg/m3 (100 lbs/cu.ft.). It is assumed that material finer than the crusher’s closed side setting (CSS) is removed from the feed. For more detailed predictions of crusher performance, consult your nearest SANDVIK office. Feed factors such as material crushability (Work index), density, gradation, moisture content and grain structure all have impact on crusher performance. Also the design of the crushing plant and process have influence.

Capacity CSS (mm) Approx. CSS Capacity (mtph) Capacity (stph)

6 1/4" 80 88

Product curves The product curve and the percentage of the crusher product that is smaller than the closed side setting (square hole, mm) is dependant on the crushability (WI) of the material, the size distribution of the feed and other factors Crushing chambers

8 5/16" 103 113

10 3/8" 130 143

13 1/2" 150 165

16 5/8" 169 186

2

4

19 3/4" 187 206

22 7/8" 204 224

25 1" 220 242

29 32 35 1"1/8 1"1/4 1"3/8 229 236 243 252 260 267

100 90 80 70 60 50 40 30 20 10 0 1

8

16

32

64

128

256

For most applications the well established CLP (constant liner performance) type of mantle is the ideal selection. CLP mantles are designed with emphasis on long liner life, high capacity and the ability to retain capacity and product gradation during the whole life of the chamber. Other customers have a strong requirement to make as fine product as possible. This need is fulfilled with the newly developed Heavy-Choke (HC) mantle, which is used when extreme reduction ratio is needed. The HC mantle has a strangulated intake which reduce material density in the chamber and allow for operation at smaller settings. A bonus effect of the design is an enlarged feed opening. HC mantles are ideally used with the F, MF and M concave rings, but can also work with MC, C and EC. CLP mantles work equally well with all concave rings. All crushing chambers in the CH-430 are installed without use of backing material and in the same topshell for maximum flexibility.

S A N D V I K M I N I N G A N D C O N S T R U C T I O N, T E L. +4 6 4 0 4 0 6 8 0 0, F A X +4 6 4 0 4 0 6 8 9 8 www.sandvik.com The above information is a general description only, is not guaranteed and contains no warranties of any kind

SANDVIK CONE CRUSHER CH430 Technical data Principle design of CLP (left) and HC (right) crushing chambers

Crushing chambers Concave ring Max.feed size with CLP chamber (mm) Max.feed size with CLP chamber (inch) Max.feed size with H-C chamber (mm) Max.feed size with H-C chamber (inch) Nominal percentage in product < CSS

EC 190 7,5 200 7,9 70%

C 145 5,7 155 6,1 73%

MC 115 4,5 125 4,9 75%

M 90 3,5 100 3,9 76%

MF 65 2,6 75 3,0 77%

F 50 2,0 55 2,2 72%

Note, SANDVIK´s definition of feed size is by determining the diameter of the largest sphere that meets the crushing chamber with a nip angle that allow it to be crushed.

Cross-section SANDVIK cone crusher. Note that the illustration show different crushing chambers to the right and to the left.

S A N D V I K M I N I N G A N D C O N S T R U C T I O N, T E L. +4 6 4 0 4 0 6 8 0 0, F A X +4 6 4 0 4 0 6 8 9 8 www.sandvik.com The above information is a general description only, is not guaranteed and contains no warranties of any kind

EF 26 1,0 NA NA 80%