• Author / Uploaded
• Mukh Saiful

Citation preview

Special Vehicle Series : 02

Hydraulic Excavator

Assembly Instructions

h t t p : / / w w w. c a n o n . c o m / c - p a r k / e n /

View of completed model * This model was designed for Papercraft and may differ from the original in some respects.

Tools ools

Assembly ssembly tip

Scissors Ruler, set square Glue (Wood glue or craft glue recommend) Exhausted ballpoint pen (out of ink) Toothpicks (for use in applying glue) Tweezers (useful for handling small parts) Pencil

Write the number of each part on the reverse side of the part in pencil upon cutting it out, to be sure you can tell which part is which later. Before gluing, crease the paper along mountain and valley fold lines. Trace along the folds with a ruler and an exhausted ballpoint pen (out of ink) to get a sharper fold. Make sure rounded sections are nice and stiff.

Key to symbols

Pattern

Assembly instructions

Dotted line

Mountain fold Fold so that the printed pattern faces outside.

Dashed and dotted line

Valley fold Fold so that the printed pattern faces inside.

Solid line

Cut parts out along this line.

The dots show where to glue the pieces together. Glue the pieces together as shown in the following examples. Some parts must be glued together along the cut surfaces.

Red dot Glue parts with the same number together. (Numbers are not printed on very small parts.)

Solid red line

Diagonal grey lines

Cut a notch along this line.

Green dot

Cut these areas out.

Blue dot

Glue areas within the same part together.

Glue to the reverse side of the specified part.

Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.

Assembly Instructions: Six A4 sheets (No. 1 to No. 6) Build this model with careful reference to the Assembly Instructions.

Red arrow Blue arrow

Glue Insert (without gluing)

Light blue

Glue tab

Light grey

Reverse side of paper Movable part This denotes a part that must be able to move after themodel is completed.Be sure to crease these parts sufficiently.

Hydraulic Excavator

Assembly Instructions

Assemble the cab. Glue flaps a, b, and c in order.

Glue flaps a, b, c, d, and e in order.

Before assembling part 3, insert part 4 in what will become the inside surface of part 3 and glue it in place.

Cross section

Taking care not to let the outline become warped, carefully glue one side at a time.

Front

Rear

Use care with the form of the rear portion of the part, making sure the top of this rear surface is flat.

Hydraulic Excavator

Assembly Instructions

Assemble part 7 and then insert part 8 from the bottom and glue it in place.

Insert part 9 to the inside of part 8 and glue it in place.

Glue part 12 in place to cover the hole and glue spot.

Note the needed gaps. C r o s s s e c t io n

C r o s s s e c t io n

When assembling these pieces, be very careful to ensure the mountain and valley folds are as shown in the illustration. Insert the pieces after checking the fit.

Cross section

Take care to glue the components of this piece together in the order shown.

Cross section

Cross section

Moving part

Cross section

Moving part

Hydraulic Excavator

Assembly Instructions

Glue to the reverse side of part 32. Cross section

Cross section

Glue flaps a and b in order.

Assemble the other side in the same way (making the left and right sides symmetrical).

e

Insid

side Out e

tsid

Ou

de

Insi

Wrap part 36 around part 34 so the seam is on the bottom, and glue it in place. Cross section Inside

Glue part E1 to the reverse of the part shown in the same way.

Cross section Outside

Outside

Make sure part 36 extrudes toward the outside.

Inside

Hydraulic Excavator

Assembly Instructions

Hydraulic Excavator

Assembly Instructions

On parts with no glue tabs, apply glue to the cut surface of the paper and glue this part to the body of the hydraulic excavator, concealing the glue tabs.(Refer to the photograph of the completed model.)

Hyd rau lic

Finished! Last, assemble the nameplate and display it together with your model.

Exc ava tor