• Author / Uploaded
• LUis Felipe Bello Rodriguez

Citation preview

LTE Radio Access, Rel. RL40, Operating Documentation, Issue 03

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description DN09142347 Issue 01 Approval Date 2013-06-14 Confidential

Nokia Siemens Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their components. If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Siemens Networks for any additional information.

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright © Nokia Siemens Networks 2013. All rights reserved

f

Important Notice on Product Safety This product may present safety risks due to laser, electricity, heat, and other sources of danger. Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product. The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f

Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen. Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen. Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.

2

Id:0900d805809d2ac0 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Table of contents This document has 140 pages. Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description . . . . . . 12

2

Pole Mounting Kit (VMPB) description. . . . . . . . . . . . . . . . . . . . . . . . . . 15

3

Flexi Pole Kit (FPKA) description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4

Flexi Pole Kit (FPKC) description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5

Flexi Pole Installation Kit (FPIA) description . . . . . . . . . . . . . . . . . . . . . 26

6

Flexi Mounting Auxiliary Bracket (FMAA) description . . . . . . . . . . . . . . 27

7

Flexi Mounting Covers for Back and Front (FMCA and FMCB) description 28

8

Flexi Module Casing (EMHA and EMTA) description . . . . . . . . . . . . . . 30

9

Flexi Mounting Shield 3U Casing (FMSC) description. . . . . . . . . . . . . . 34

10

10.4

Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA/B) description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA/FPBB) operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Flexi Power Module (FPMA) dimensions and weight . . . . . . . . . . . . . . 38 Flexi Power Module (FPMA) and sub-module (FPAA and FPBA/FPBB) interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Flexi power sub-module (FPAA and FPBA/FPBB) LED indications . . . 41

11 11.1 11.2 11.3 11.4

Flexi Power DC/DC Module (FPDA) description . . . . . . . . . . Flexi Power DC/DC Module (FPDA) operation . . . . . . . . . . . Flexi Power DC/DC Module (FPDA) dimensions and weight Flexi Power DC/DC Module (FPDA) interfaces . . . . . . . . . . . Flexi Power DC/DC Module (FPDA) LED indications . . . . . .

12 12.1 12.2

Flexi Power Rectifier (FPRA) description. . . . . . . . . . . . . . . . . . . . . . . . 47 Flexi Power Rectifier (FPRA) operation . . . . . . . . . . . . . . . . . . . . . . . . . 47 Flexi Power Rectifier (FPRA) dimensions . . . . . . . . . . . . . . . . . . . . . . . 47

13 13.1 13.2

Flexi Power AC/DC Submodule 230V (FPAC) description . . . . . . . . . . 49 Flexi Power AC/DC Submodule 230V (FPAC) dimensions and weight. 49 Flexi Power AC/DC Submodule 230V (FPAC) LED indications . . . . . . 49

14 14.1 14.2

Flexi Power AC/DC Submodule 230V (FPAD) description . . . . . . . . . . 51 Flexi Power AC/DC Submodule 230V (FPAD) dimensions and weight. 51 Flexi Power AC/DC Submodule 230V (FPAD) LED indications . . . . . . 51

15 15.1 15.2

Flexi Power Distribution and Fuses (FPFB) description . . . . . . . . . . . . 53 Flexi Power Distribution and Fuses (FPFB) operation. . . . . . . . . . . . . . 53 Flexi Power Distribution and Fuses (FPFB) dimensions and weight . . . 54

16 16.1

Flexi Power Distribution and Fuses Outdoor (FPFC) description . . . . . 55 Flexi Power Distribution and Fuses Outdoor (FPFC) operation. . . . . . . 55

10.1 10.2 10.3

DN09142347

Id:0900d805809d2ac0 Confidential

........ ........ ........ ........ ........

43 43 44 45 46

3

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

4

16.2

Flexi Power Distribution and Fuses Outdoor (FPFC) dimensions and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

17 17.1

Flexi Power Distribution Sub-Module (FPFD) description. . . . . . . . . . . . 58 Flexi Power Distribution Sub-Module (FPFD) operation . . . . . . . . . . . . . 58

18 18.1 18.2

Flexi Power Distribution and Fuses Indoor (FPFI) description . . . . . . . . 59 Flexi Power Distribution and Fuses Indoor (FPFI) operation . . . . . . . . . 59 Flexi Power Distribution and Fuses Indoor (FPFI) dimensions. . . . . . . . 60

19 19.1 19.2 19.3 19.4

Flexi System Flexi System Flexi System Flexi System Flexi System

External OVP (FSEC) description . . . . . . . . . . . . . . . . . . . 61 External OVP (FSEC) operation . . . . . . . . . . . . . . . . . . . . 61 External OVP (FSEC) dimensions and weight . . . . . . . . . 64 External OVP (FSEC) interfaces . . . . . . . . . . . . . . . . . . . . 65 External OVP (FSEC) LED indications . . . . . . . . . . . . . . . 66

20 20.1 20.2 20.3

Flexi System Flexi System Flexi System Flexi System

External OVP (FSES) description . . . . . . . . . . . . . . . . . . . 67 External OVP (FSES) operation . . . . . . . . . . . . . . . . . . . . 68 External OVP (FSES) dimensions and weight . . . . . . . . . 69 External OVP (FSES) interfaces . . . . . . . . . . . . . . . . . . . . 70

21 21.1 21.2

Flexi Fiber Optical Distribution Unit (FODA) description . . . . . . . . . . . . . 71 Flexi Fiber Optical Distribution Unit (FODA) operation . . . . . . . . . . . . . . 71 Flexi Fiber Optical Distribution Unit (FODA) dimensions . . . . . . . . . . . . 71

22 22.1 22.2 22.3

Flexi System Flexi System Flexi System Flexi System

23

GPS Antenna Kit (FYGA) and GPS GLONASS Receiver Antenna (FYGB) description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

24 24.1 24.2 24.3 24.4

Flexi GPS Flexi GPS Flexi GPS Flexi GPS Flexi GPS

....... ....... ....... ....... .......

...... ...... ...... ...... ......

. . . . . . 82 . . . . . . 82 . . . . . . 83 . . . . . . 83 . . . . . . 84

25 25.1 25.2 25.3

Flexi Cabinet for Indoor (FCIA) description. . . . . . . . . . . Flexi Cabinet for Indoor (FCIA) construction. . . . . . . . . . Flexi Cabinet for Indoor (FCIA) optional items . . . . . . . . Flexi Cabinet for Indoor (FCIA) dimensions and weight .

...... ...... ...... ......

. . . . . . 85 . . . . . . 85 . . . . . . 86 . . . . . . 87

26 26.1 26.2 26.3

Flexi Cabinet for Outdoor (FCOA) description . . . . . . . . . . . . . . Flexi Cabinet for Outdoor (FCOA) construction . . . . . . . . . . . . . Flexi Cabinet for Outdoor (FCOA) optional items . . . . . . . . . . . . Flexi Cabinet for Outdoor (FCOA) dimensions and weight . . . . .

. . . . . . 88 . . . . . . 88 . . . . . . 90 . . . . . . 93

27 27.1 27.2

Flexi Mounting Shield (FMSA and FMSB) description . . . . . . . . . . . . . . 94 Flexi Mounting Shield (FMSA and FMSB) operation and construction . . 94 Flexi Mounting Shield (FMSA and FMSB) dimensions and weights . . . . 96

28

Flexi Cabinet Outdoor Small (FCOS) description . . . . . . . . . . . . . . . . . . 97

External Alarm (FSEB) description . . . . . . . . . . . . . . . . . . 73 External Alarm (FSEB) operation . . . . . . . . . . . . . . . . . . . 73 External Alarm (FSEB) interfaces . . . . . . . . . . . . . . . . . . . 75 External Alarm (FSEB) dimensions and weight . . . . . . . . 77

Box (FYGD) description . . . . . . . . . . Box (FYGD) operation . . . . . . . . . . . Box (FYGD) dimensions and weight Box (FYGD) interfaces. . . . . . . . . . . Box (FYGD) LED indications . . . . . .

Id:0900d805809d2ac0 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

DN09142347

28.1 28.2 28.3

Flexi Cabinet Outdoor Small (FCOS) construction . . . . . . . . . . . . . . . . 97 Flexi Cabinet Outdoor Small (FCOS) optional items . . . . . . . . . . . . . . . 98 Flexi Cabinet Outdoor Small (FCOS) dimensions and weight . . . . . . . . 98

29 29.1 29.2 29.3

Flexi Mounting Kit Vertical for 2G (FMUA) description . . . . . . . . . . . . Flexi Mounting Kit Vertical for 2G (FMUA) operation. . . . . . . . . . . . . . Flexi Mounting Kit Vertical for 2G (FMUA) construction . . . . . . . . . . . Technical properties of Flexi Mounting Kit Vertical for 2G (FMUA) . . .

30 30.1 30.2

Flexi Mounting Kit Horizontal for 2G (FMUB) description . . . . . . . . . . 103 Flexi Mounting Kit Horizontal for 2G (FMUB) operation and construction . 103 Technical properties of Flexi Mounting Kit Horizontal for 2G (FMUB) . 104

31

Talk Conversion Kit (EMIB) description . . . . . . . . . . . . . . . . . . . . . . . . 105

32

UltraSite Outdoor Side Kit (OSKA) description . . . . . . . . . . . . . . . . . . 106

33

UltraSite IDC_ Roof Kit (IRSA) description . . . . . . . . . . . . . . . . . . . . . 108

34 34.1 34.2 34.3

Flexi TRS External Filter for FHCA (FFCB) description. . . . . . . . . . . . Flexi TRS External Filter for FHCA (FFCB) operation . . . . . . . . . . . . . Flexi TRS External Filter for FHCA (FFCB) interfaces. . . . . . . . . . . . . Flexi TRS External Filter for FHCA (FFCB) dimensions and weight . .

109 109 110 111

35 35.1 35.2 35.3

Flexi TRS External Filter for FXCA (FFCC) description. . . . . . . . . . . . Flexi TRS External Filter for FXCA (FFCC) operation . . . . . . . . . . . . . Flexi TRS External Filter for FXCA (FFCC) interfaces. . . . . . . . . . . . . Flexi TRS External Filter for FXCA (FFCC) dimensions and weight . .

112 112 112 113

36 36.1 36.2 36.3 36.4 36.5

Repeater Interface Module (FHCC) description. . . . . . . . . . . . . . . . . . Repeater Interface Module (FHCC) operation and main blocks . . . . . Repeater Interface Module (FHCC) interfaces . . . . . . . . . . . . . . . . . . Repeater Interface Module (FHCC) dimensions and weight . . . . . . . . Repeater Interface Module (FHCC) power requirements . . . . . . . . . . Repeater Interface Module (FHCC) LED indications . . . . . . . . . . . . . .

114 114 114 116 116 116

37 37.1 37.2 37.3 37.4 37.5 37.6 37.7 37.8 37.9

Flexi Multiradio BTS and Flexi Multiradio 10 BTS cables and SFPs . . Transmission cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single-mode fiber cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi-mode fiber cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Small form-factor pluggable transceivers (SFPs) . . . . . . . . . . . . . . . . DC feeding and extension kit cables . . . . . . . . . . . . . . . . . . . . . . . . . . Synchronization cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GPS feeding cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAC cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

118 118 121 122 125 128 131 133 134 136

38

Appendix Casing and cover kits need for Flexi Multiradio units. . . . . . 137

Id:0900d805809d2ac0 Confidential

. 99 . 99 101 102

5

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

List of figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44

6

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) version 206 . . . . . . 12 External interfaces of Flexi Mounting Kit for Floor, Wall and Pole (FMFA) . 14 Pole Mounting Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Flexi Pole Kit (FPKA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FPKA with four 3U Flexi Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Flexi Pole Kit (FPKC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Two RRHs installed on two Flexi Pole Kits (FPKC) . . . . . . . . . . . . . . . . 21 Expansion paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Basic FPKC configurations with no expansion path . . . . . . . . . . . . . . . . 23 FPKC and RRH configurations, expansion path 1 . . . . . . . . . . . . . . . . . 24 FPKC and RRH configurations, expansion path 2 . . . . . . . . . . . . . . . . . 24 FPKC and 2U/3U module configurations using FMFA . . . . . . . . . . . . . . 25 Flexi Pole Installation Kit (FPIA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Flexi Mounting Auxiliary Bracket (FMAA) . . . . . . . . . . . . . . . . . . . . . . . . 27 Flexi Mounting Covers for Back and Front 3U (FMCA) . . . . . . . . . . . . . 28 Flexi Module Casing (EMHA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Flexi Module Casing (EMTA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Flexi Side Covers (FMHA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Flexi Side Covers (FMTA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Flexi Mounting Shield 3U Casing (FMSC) . . . . . . . . . . . . . . . . . . . . . . . 34 Flexi Power Module (FPMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Flexi Power Module (FPMA) with a full configuration of two FPAAs and two FPBAs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 FPAA LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 FPBA/B LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Flexi Power DC/DC Module (FPDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Front panel of the FPDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Flexi Power Distribution and Fuses (FPFB) . . . . . . . . . . . . . . . . . . . . . . 53 Flexi Power Distribution and Fuses Outdoor (FPFC) . . . . . . . . . . . . . . . 55 Flexi Power Distribution Sub-Module (FPFD) . . . . . . . . . . . . . . . . . . . . . 58 Flexi Power Distribution and Fuses Indoor (FPFI) . . . . . . . . . . . . . . . . . 59 Flexi Power Distribution and Fuses Indoor (FPFI) front panel . . . . . . . . 59 Flexi System External OVP (FSEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 FSEC internal wiring (version 6Yxxxxxxxxx). . . . . . . . . . . . . . . . . . . . . . 62 FSEC external wiring (version 6Yxxxxxxxxx) . . . . . . . . . . . . . . . . . . . . . 63 Flexi System External OVP (FSES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Flexi System External OVP (FSES) interfaces . . . . . . . . . . . . . . . . . . . . 70 Flexi Fiber Optical Distribution Unit (FODA) . . . . . . . . . . . . . . . . . . . . . . 71 Flexi System External Alarm (FSEB) . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 FSEB interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 FSEB PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 GPS Antenna Kit (FYGA)/GPS GLONASS Receiver Antenna (FYGB) . 78 FYGA/FYGB mounted on a pole using GPS Mounting Kit (FYMA) . . . . 79 Flexi GPS Surge Protector Kit (FYEA) . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Sync In port on the FSMC/D/E front panel (FYGA only). . . . . . . . . . . . . 80

Id:0900d805809d2ac0 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73

DN09142347

Sync In port on the FSMF/G/L front panel . . . . . . . . . . . . . . . . . . . . . . . 80 GPS Box deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Flexi GPS Box (FYGD) front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Flexi Cabinet for Indoor (FCIA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Flexi Cabinet for Outdoor (FCOA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Flexi Cabinet Air Filter (FCFA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Flexi Cabinet Site Support Module (FCSA) . . . . . . . . . . . . . . . . . . . . . . 91 Flexi Cabinet Fire Detector (FCDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Isometric view of the FMSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Isometric view of the FMSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Flexi Cabinet Outdoor Small (FCOS) installed on the floor . . . . . . . . . . 97 Flexi Mounting Kit Vertical for 2G (FMUA) with Flexi Multiradio BTS installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 FMUA parts (dual and single racks). . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Flexi Mounting Kit Horizontal for 2G (FMUB). . . . . . . . . . . . . . . . . . . . 103 Parts needed for installing Flexi BTS modules in Citytalk cabinet with Talk Conversion Kit (EMIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 UltraSite Outdoor Side Kit (OSKA) . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Side kits fixed to the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 UltraSite IDC_ Roof Kit (IRSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Mounting in forward position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Flexi TRS External Filter for FHCA (FFCB) . . . . . . . . . . . . . . . . . . . . . 109 Flexi TRS External Filter for FHCA (FFCB) mounted on a pole . . . . . 110 Flexi TRS External Filter for FXCA (FFCC) . . . . . . . . . . . . . . . . . . . . . 112 Bottom view of the FFCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Repeater Interface Module (FHCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Front panel view of the FHCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 FPCA Dual power cable 2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 FPCB DC cable multi-beam - multi-beam 2 m. . . . . . . . . . . . . . . . . . . 130 FPCC DC cable multi-beam - open 2 m . . . . . . . . . . . . . . . . . . . . . . . 130 Standard DC cable open - open (single cable) . . . . . . . . . . . . . . . . . . 130

Id:0900d805809d2ac0 Confidential

7

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

List of tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 Table 22 Table 23 Table 24 Table 25 Table 26 Table 27 Table 28 Table 29 Table 30 Table 31 Table 32 Table 33 Table 34 Table 35 Table 36 Table 37 Table 38 Table 39 Table 40 Table 41

8

RAT releases covered by the document . . . . . . . . . . . . . . . . . . . . . . . . 11 Dimensions and weight of the FMFA . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Pole Mounting Kit (VMPB) delivery contents . . . . . . . . . . . . . . . . . . . . . 15 Pole Mounting Kit (VMPB) dimensions and weight . . . . . . . . . . . . . . . . 15 Flexi Pole Kit (FPKA) delivery contents . . . . . . . . . . . . . . . . . . . . . . . . . 17 2U/3U modules inside casings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Number of Flexi Pole Kits (FPKC) required . . . . . . . . . . . . . . . . . . . . . . 20 Flexi Mounting Covers for Back and Front 3U (FMCA) dimensions . . . 29 Flexi Mounting Covers for Back and Front 2U (FMCB) dimensions . . . 29 Grounding cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Dimensions and weight of Flexi Module Casing (EMHA) . . . . . . . . . . . 33 Dimensions and weight of Flexi Module Casing (EMTA) . . . . . . . . . . . . 33 Dimensions and weight of the FPMA . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Flexi Power Module (FPMA) front panel connectors, types and purposes 39 Flexi Power AC/DC sub-module (FPAA) front panel connectors, types and purposes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Flexi Power Battery sub-module (FPBA/FPBB) front panel connectors, types and purposes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 FPAA LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 FPBA/B LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Dimensions and weight of the FPDA . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 FPDA front panel connectors, connector types and purposes . . . . . . . . 45 FPDA LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Flexi Power Rectifier (FPRA) dimensions . . . . . . . . . . . . . . . . . . . . . . . 47 Flexi Power AC/DC Submodule 230V (FPAC) dimensions . . . . . . . . . . 49 Flexi Power AC/DC Submodule 230V (FPAC) LED indications . . . . . . 50 Flexi Power AC/DC Submodule 230V (FPAD) dimensions . . . . . . . . . . 51 Flexi Power AC/DC Submodule 230V (FPAD) LED indications . . . . . . 52 Flexi Power Distribution and Fuses (FPFB) dimensions . . . . . . . . . . . . 54 Flexi Power Distribution and Fuses Outdoor (FPFC) dimensions and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Flexi Power Distribution and Fuses Indoor (FPFI) dimensions . . . . . . . 60 Flexi System External OVP (FSEC) dimensions and weight . . . . . . . . . 64 Allowed cable thicknesses for Flexi System External OVP (FSEC) . . . 65 FSEC E4xxxxxxxxx and S1/M2/V5xxxxxxxxx LED indications . . . . . . . 66 Allowed cable thicknesses for Flexi System External OVP (FSES) . . . . 70 Flexi Fiber Optical Distribution Unit (FODA) dimensions . . . . . . . . . . . . 71 Alarms supported by System Module variants . . . . . . . . . . . . . . . . . . . . 73 Interface and connector overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Flexi System External Alarm (FSEB) dimensions and weight dimensions 77 Technical details of FYGA/FYGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 GPS Mounting Kit (FYMA) dimensions (antenna excluded) . . . . . . . . . 80 Flexi GPS Box (FYGD) dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Flexi GPS Box (FYGD) interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Id:0900d805809d2ac0 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 Table 53 Table 54 Table 55 Table 56 Table 57 Table 58 Table 59 Table 60 Table 61 Table 62 Table 63 Table 64 Table 65 Table 66 Table 67 Table 68 Table 69 Table 70 Table 71 Table 72 Table 73 Table 74 Table 75 Table 76 Table 77 Table 78

DN09142347

Dimensions and weight of Flexi Cabinet for Indoor (FCIA) . . . . . . . . . . 87 Dimensions and weight of Flexi Cabinet for Outdoor (FCOA) . . . . . . . 93 Flexi Mounting Shield 6U (FMSA) dimensions and weight . . . . . . . . . 96 Flexi Mounting Shield 18U (FMSB) dimensions and weight . . . . . . . . . 96 Flexi Cabinet Outdoor Small (FCOS) dimensions and weight . . . . . . . 98 FMUA dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 FMUB dimensions and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Flexi TRS External Filter for FHCA (FFCB) interfaces . . . . . . . . . . . . 111 Flexi TRS External Filter for FHCA (FFCB) dimensions and weight . . 111 Flexi TRS External Filter for FXCA (FFCC) interfaces . . . . . . . . . . . . 113 Flexi TRS External Filter for FXCA (FFCC) dimensions and weight . . 113 Repeater Interface Module (FHCC) interfaces . . . . . . . . . . . . . . . . . . 115 Repeater Interface Module (FHCC) dimensions and weight . . . . . . . 116 Repeater Interface Module (FHCC) LED indications . . . . . . . . . . . . . 116 Flexi Multiradio 10 BTS transmission cables . . . . . . . . . . . . . . . . . . . 118 Flexi Multiradio BTS transmission cables . . . . . . . . . . . . . . . . . . . . . . 118 Flexi Multiradio BTS GSM/EDGE transmission cables . . . . . . . . . . . . 120 Single-mode fibers 90°-90° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Single-mode fibers 0°-90° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Multi-mode fibers 90°-90° OM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Multi-mode fibers 90°-90° OM3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Multi-mode fibers 0°-90° OM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 3 Gb SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 6 Gb SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 1 Gb transmission SFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 DC feeding and extension kit cables . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Flexi Multiradio BTS synchronization cables . . . . . . . . . . . . . . . . . . . 131 GSP feeding cables for System Module variants FSMF/G/L . . . . . . . 133 GSP feeding cables for System Module variants FSMC/D/E . . . . . . . 133 Flexi Multiradio BTS EAC cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Flexi Multiradio BTS miscellaneous cables . . . . . . . . . . . . . . . . . . . . . 136 Casing and cover kits need for System Modules . . . . . . . . . . . . . . . . 137 Casing and cover kits need for Radio Modules . . . . . . . . . . . . . . . . . 137 Casing and cover kits need for Power Modules . . . . . . . . . . . . . . . . . 138 EMHA compatibility with Flexi EDGE System Modules . . . . . . . . . . . 139 FMCA compatibility with Flexi Multiradio System Modules . . . . . . . . . 139 FMCA compatibility with Flexi Power Modules . . . . . . . . . . . . . . . . . . 139

Id:0900d805809d2ac0 Confidential

9

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

10

Id:0900d805809d2ac0 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Summary of changes

Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues. This document is published with the product releases listed in the following table. The document is common for all Radio Access Technologies (RAT) and therefore may contain information about hardware units that are not available or supported in a specific release or RAT. Radio Access Technology (RAT)

Product release

GSM

RG30

WCDMA

RU40

LTE

RL35TD RL40 RL50

Table 1

RAT releases covered by the document

This is the first issue of the document.

DN09142347

Id:0900d805809bf7b4 Confidential

11

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

1 Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description This section describes the following hardware: •

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) 470149A

Figure 1

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) version 206

Flexi BTS modules are installed on the floor, wall or pole using Flexi Mounting Kit for Floor, Wall and Pole (FMFA). The plinth is required for BTS site installations without a cabinet and it provides grounding points for BTS and module grounding. The mounting principles are the following: •

•

•

In floor mounting, the plinth is fixed directly onto the floor. To meet the Telcordia GR63-CORE Vibrational requirements for earthquake Zone 4 requirement, the maximum number of modules in a stack is five (maximum total height 15 U). To meet the Telcordia GR-63-CORE Vibrational requirements for earthquake Zone 2 requirement, the maximum number of modules in a stack is nine (maximum total height 22 U). In wall mounting, the plinth is fixed onto the wall either by using adapter mechanics (FMFA version 103 or older) or directly to the wall. The maximum number of modules per plinth is two. If using FMFA version 103 or older, in pole mounting the plinth is fixed onto a pole mounting kit (VMPB/FPKA/FPKC) by using adapter mechanics. The maximum number of modules per plinth is two. The FMFA delivery includes two fixing plates for the casings. Used in pole and wall installations, the plates are attached across two module casings on both sides of the modules.

The plinth has a back stop that prevents installing the BTS too near to a wall. FMFA dimensions and weight The dimensions and weight of the FMFA are presented in Table 2 Dimensions and weight of the FMFA.

12

Id:0900d805809c191f Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description

Property

Value

Height

48 mm (1.9 in.)

Depth without back stop

455 mm (17.9 in.)

Width

505 mm (19.9 in.)

Weight

2.9 kg (6.39 lbs)

Table 2

Dimensions and weight of the FMFA

For installation instructions, see Installing Flexi Multiradio BTS LTE Modules for Stack, Wall, and Pole Configurations. External connections The plinth has the following fixing interfaces: • • • • • • • • •

ESD stud (1 pcs) Casing fixing points (4 pcs) Pole/wall adapter fixing points (8 pcs) Threads for the lifting eye bolts (4 pcs) Modules grounding (12 pcs) BTS grounding (2 pcs) Casing locking points (2 pcs) Anchoring points to floor (4 pcs) Fixing plate fixing points (4 pcs)

See the following figure for the external fixing interfaces of the FMFA.

DN09142347

Id:0900d805809c191f Confidential

13

Flexi Mounting Kit for Floor, Wall and Pole (FMFA) description

Fixing holes for fixing plates

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Casing fixing points Fixing holes for fixing plates

Threads for the lifting eye bolts

Casing locking points Threads for the lifting eye bolts

BTS grounding

ESD Stud

BTS grounding Modules grounding

Anchoring points to floor

Figure 2

14

External interfaces of Flexi Mounting Kit for Floor, Wall and Pole (FMFA)

Id:0900d805809c191f Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Pole Mounting Kit (VMPB) description

2 Pole Mounting Kit (VMPB) description This section describes the following hardware: •

Pole Mounting Kit (VMPB) 469978A

DN70415461

Figure 3

Pole Mounting Kit

Pole Mounting Kit (VMPB) enables BTS installation on a pole 60-300 mm (2.4-11.8 in.) in diameter. See Table 3 Pole Mounting Kit (VMPB) delivery contents for the delivery contents of the VMPB. Item

Quantity

Pole Mounting Kit (VMPB)

1

Mounting blocks

2 pcs

M8x25 bolts

8 pcs

M10x120 bolts

4 pcs

M10x200 bolts

4 pcs

M10x300 bolts

4 pcs

Washers

4 pcs

Table 3

Pole Mounting Kit (VMPB) delivery contents

See Table 4 Pole Mounting Kit (VMPB) dimensions and weight for dimensions and weight of the VMPB. Property

Value

Height

60 mm (2.4 in.)

Width

350 mm (13.7 in.)

Depth (pole diameter 120 mm)

200 mm (7.9 in.)

Weight

7 kg (15.4 lb)

Table 4

DN09142347

Pole Mounting Kit (VMPB) dimensions and weight

Id:0900d805809d19d5 Confidential

15

Pole Mounting Kit (VMPB) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

For installation instructions, see Installing Flexi Multiradio BTS LTE Modules for Stack, Wall, and Pole Configurations.

16

Id:0900d805809d19d5 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Pole Kit (FPKA) description

3 Flexi Pole Kit (FPKA) description This section describes the following hardware: •

Flexi Pole Kit (FPKA) 471649A

Bolt M8x20

Fixingpoints 64mm (2.5 in.) Bolt M10X120 105 mm thread

Fixingpoints 184mm (7.2 in.)

Figure 4

Flexi Pole Kit (FPKA)

Flexi Pole Kit (FPKA) can be used with poles between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter. The most commonly used size is 80 mm (3.1 in.). The FPKA can replace the VMPB Pole Mounting kit in installations where the pole diameter is less than 120 mm (4.7 in.). The width of the fixing points is 184 mm (7.2 in) and 64 mm (2.5 in). There are fixing points on three sides of the FPKA. The M10 screws should be tightened to 30 Nm (22.13 ft-lb) and the M8 screws to 20 Nm (14.75 ft-lb). The FPKA can carry the maximum weight of 160 kg (352.7 lbs). The delivery contents of the FPKA are listed in Table 5 Flexi Pole Kit (FPKA) delivery contents. Item

Quantity

FPKA Bracket

1 pcs

Bolt M8 x 20

6 pcs

Bolt restrainer

2 pcs

FPKA bracket strainer

1 pcs

Bolt M10 x120 105 mm thread

2 pcs

ISO 4762 (DIN912)

Table 5

Flexi Pole Kit (FPKA) delivery contents

Installation with Flexi modules The FPKA has room for a maximum of four 3U Flexi modules (12U total). Two modules (or casings) can be installed on opposite sides of the FPKA. See Figure 5 FPKA with four 3U Flexi Modules for the FPKA installation with four 3U modules.

DN09142347

Id:0900d805809d19ed Confidential

17

Flexi Pole Kit (FPKA) description

Figure 5

18

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

FPKA with four 3U Flexi Modules

Id:0900d805809d19ed Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Pole Kit (FPKC) description

4 Flexi Pole Kit (FPKC) description This section describes the following hardware: •

Flexi Pole Kit (FPKC) 472821A

Figure 6

Flexi Pole Kit (FPKC)

Flexi Pole Kit (FPKC) is based on the VMPB and FPKA pole mounting kits and fulfills the same functional requirements. It allows four-directional installations of Flexi modules and Remote Radio Heads. The following installations are supported: •

For 2U/3U module installations, see Table 6 2U/3U modules inside casings: Pole size

Number of 2U/3U casings

FMFA required

Expansion possible

Mixed configurations (casings and RRHs) supported

60 to 300 mm (2.36 in to 11.81 in)

1 to 4

No

No

No

60 to 115 mm (2.36 in to 4.53 in)

1 to 8

Yes

Yes

Yes

190 to 300 mm (7.48 in to 11.81 in) Table 6 •

DN09142347

2U/3U modules inside casings

Up to six Remote Radio Heads (with a maximum of 425 mm (16.7 in.) total width each, solar shields included).

Id:0900d805809c297f Confidential

19

Flexi Pole Kit (FPKC) description

•

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Square-shaped poles and L-bar poles with L-bar size between 50 x 50 mm (2 x 2 in.) and 210 x 210 mm (8.3 x 8.3 in.) are supported.

A maximum configuration of eight 3U modules with front and back covers and four FMFAs weighs 228 kg (502.7 lbs). Number of FPKCs

2U/3U casing + FMFA

RRH

1

N/A

N/A

N/A

2

1 to 4

1 to 4 + 1 to 2 FMFAs

1 to 2

3

-

1 to 4 + 1 to 2 FMFAs

1 to 3

4

-

1 to 6 + 1 to 3 FMFAs

1 to 4

5

-

1 to 8 + 1 to 4 FMFAs

1 to 4

6

-

-

1 to 6

Table 7

20

2U/3U casing

Number of Flexi Pole Kits (FPKC) required

Id:0900d805809c297f Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 7

Flexi Pole Kit (FPKC) description

Two RRHs installed on two Flexi Pole Kits (FPKC)

Figures Figure 8 Expansion paths, Figure 9 Basic FPKC configurations with no expansion path, Figure 10 FPKC and RRH configurations, expansion path 1, Figure 11 FPKC and RRH configurations, expansion path 2 and Figure 12 FPKC and 2U/3U module configurations using FMFA show the principles of creating basic and expansion-optimized configurations using FPKC kits. If you are going to expand your 2U/3U module configurations later, utilise Flexi Mounting Kits for Floor, Wall and Pole (FMFA) starting from the first configuration. FMFAs are required for configurations larger than four 2U/3U modules to allow enough room for a four-directional installation.

DN09142347

Id:0900d805809c297f Confidential

21

Flexi Pole Kit (FPKC) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Expansion paths

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

Figure 8

22

FPKC

FPKC

FPKC

Expansion paths

Id:0900d805809c297f Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Pole Kit (FPKC) description

FPKC configurations with no expansion path

RRH FPKC RRH

RRH

FPKC RRH 2 x FPKC & 2 x RRH

RFM RFM FPKC RFM RFM

RFM RFM

FPKC RFM RFM 2 x FPKC & 4 x RFM

Figure 9

DN09142347

Basic FPKC configurations with no expansion path

Id:0900d805809c297f Confidential

23

Flexi Pole Kit (FPKC) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

RRH

RRH

RRH

FPKC

FPKC

FPKC and RRH configurations, expansion path 1

RRH FPKC

FPKC

FPKC

FPKC

RRH RRH

RRH

FPKC

RRH

FPKC

FPKC

FPKC

FPKC

FPKC

FPKC

RRH FPKC

RRH

RRH

4 x FPKC & 4 x RRH

FPKC

6 x FPKC & 5 x RRH Figure 10

RRH

RRH

FPKC

FPKC

4 x FPKC & 3 x RRH

RRH

FPKC

RRH

RRH

2 x FPKC & 2 x RRH

RRH

RRH

RRH

RRH

FPKC

FPKC

FPKC

FPKC

6 x FPKC & 6 x RRH

FPKC and RRH configurations, expansion path 1

FPKC

FPKC RRH

RRH

2 x FPKC & 2 x RRH

Figure 11

24

FPKC

3 x FPKC & 3 x RRH

FPKC

RRH

FPKC

FPKC

FPKC

RRH

RRH

FPKC

RRH

RRH

RRH

FPKC

FPKC and RRH configurations, expansion path 2

RRH

4 x FPKC & 4 x RRH

FPKC and RRH configurations, expansion path 2

Id:0900d805809c297f Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Pole Kit (FPKC) description

FPKC and 2U/3U module configurations using FMFA

RFM

RFM

FMFA FPKC

FMFA FPKC

RFM

FPKC

FMFA FPKC

RFM

RFM

RFM

FPKC

2 x FPKC & 1 x FMFA & 2 X RFM

RFM

FPKC

RFM

FPKC

FPKC FMFA

FMFA FPKC

FMFA FPKC

FMFA FPKC

RFM

RFM

RFM

RFM

RFM

RFM

RFM

RFM

FPKC FMFA

FMFA FPKC

RFM

RFM

3 x FPKC & 2 x FMFA & 4 x RFM

FPKC FMFA RFM

4 x FPKC & 3 x FMFA & 6 x RFM

RFM

5 x FPKC & 4 x FMFA & 8 x RFM

Figure 12

DN09142347

FPKC and 2U/3U module configurations using FMFA

Id:0900d805809c297f Confidential

25

Flexi Pole Installation Kit (FPIA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

5 Flexi Pole Installation Kit (FPIA) description This section describes the following hardware: •

Flexi Pole Installation Kit (FPIA) 471767A

DN70458657

Figure 13

Flexi Pole Installation Kit (FPIA)

Flexi Pole Installation Kit (FPIA) consists of an installation plate, straining strap and four screws. It is used for installing the following auxiliary units to a pole: • • •

Flexi System External Alarm (FSEB) Flexi System External OVP (FSEC) Flexi System External OVP (FSES)

The pole can between 60 mm (2.4 in.) and 120 mm (4.7 in.) in diameter. There are two sets of fixing points on the installation plate. The FPIA can carry the weight of 5 kg (11 lbs). For the FPIA delivery contents, see Contents of the Flexi Pole Installation Kit (FPIA) delivery in Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items.

26

Id:0900d805809d1a23 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Mounting Auxiliary Bracket (FMAA) description

6 Flexi Mounting Auxiliary Bracket (FMAA) description This section describes the following hardware: •

Flexi Mounting Auxiliary Bracket (FMAA) 471657A

Spring washer

Figure 14

Flexi Mounting Auxiliary Bracket (FMAA)

Flexi Mounting Auxiliary Bracket (FMAA) can be used to mount auxiliary boxes (FSEB, FSEC) in pole, wall, stack, or EMIA/EMIB installations. One FSEB can be installed to the Citytalk Cabinet without the use of FMAA. The FMAA is mounted to the top casing in horizontal stacks and the outer casing in vertical installations. The auxiliary boxes are then mounted to the FMAA based on their own installation principles. There is enough space for a maximum of one FSEC box and one FSEB box, or two FSEC boxes.

DN09142347

Id:0900d805809d1a75 Confidential

27

Flexi Mounting Covers for Back and Front (FMCA and FMCB) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

7 Flexi Mounting Covers for Back and Front (FMCA and FMCB) description This section describes the following hardware: • •

Flexi Mounting Covers for Back and Front 3U (FMCA) 470239A Flexi Mounting Covers for Back and Front 2U (FMCB) 470332A

Front cover

Back cover

2 x cable entry

2 x maintenance strap

Figure 15

Grounding cable

Flexi Mounting Covers for Back and Front 3U (FMCA)

Flexi Mounting Covers for Back and Front are optional 3U (FMCA) and 2U(FMCB) module covers that are required in installations without a cabinet. The primary functions of the covers are visual protection and mechanical protection for the cables. Furthermore, the back cover protects the installer's fingers from the rotating fans. For installation instructions, see Installing back covers and Installing front covers in Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items. The FMCA and FMCB deliveries include a grounding cable. Note that a grounding cable is not included in any module deliveries. FMCA/FMCB dimensions The dimensions of the FMCA are presented in Table 8 Flexi Mounting Covers for Back and Front 3U (FMCA) dimensions.

28

Id:0900d805809bf71c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Mounting Covers for Back and Front (FMCA and FMCB) description

Property

Front cover

Back cover

Height

128 mm

128 mm

(5 in.)

(5 in.)

492 mm

446 mm

(19.4 in.)

(17.6 in.)

100 mm

37 mm

(3.9 in.)

(1.5 in.)

Width

Depth

Table 8

Flexi Mounting Covers for Back and Front 3U (FMCA) dimensions

The dimensions of the FMCB are presented in Table 9 Flexi Mounting Covers for Back and Front 2U (FMCB) dimensions. Property

Front cover

Back cover

Height

83 mm

83 mm

(3.3 in.)

(3.3 in.)

492 mm

446 mm

(19.4 in.)

(17.6 in.)

100 mm

37 mm

(3.9 in.)

(1.5 in.)

Width Depth

Table 9

Property

Value

Length

1.3 m (4.3 ft.)

Thickness

16 mm2 (5 AWG)

Table 10

DN09142347

Flexi Mounting Covers for Back and Front 2U (FMCB) dimensions

Grounding cable

Id:0900d805809bf71c Confidential

29

Flexi Module Casing (EMHA and EMTA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

8 Flexi Module Casing (EMHA and EMTA) description This section describes the following hardware: • • •

Flexi Module Casing (EMHA) for 3 height units (3U) 470316A Flexi Module Casing (EMTA) for 2 height units (2U) 470315A Optional items (to be ordered separately): • Flexi Side Covers (FMHA) for 3 height units (3U) 471524A • Flexi Side Covers (FMTA) for 2 height units (2U) 471523A

Figure 16

30

Flexi Module Casing (EMHA)

Id:0900d805809c0086 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 17

Flexi Module Casing (EMHA and EMTA) description

Flexi Module Casing (EMTA)

Optional Flexi Module Casing (EMHA/EMTA) is used to fix the modules to floor, wall, or pole. Module casings enable module replacement without the need to completely dismantle the BTS installation and ensure environmental protection against different environments. There are two optional casings available depending on the unit height. Optional Flexi Side Covers Flexi Side Covers are available as an optional item. The FMHA and FMTA are presented in Figure 18 Flexi Side Covers (FMHA) and Figure 19 Flexi Side Covers (FMTA):

DN09142347

Id:0900d805809c0086 Confidential

31

Flexi Module Casing (EMHA and EMTA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 18

Flexi Side Covers (FMHA)

Figure 19

Flexi Side Covers (FMTA)

For more information, see Appendix Casing and cover kits need for Flexi Multiradio units.

32

Id:0900d805809c0086 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Module Casing (EMHA and EMTA) description

Flexi Module Casing (EMHA/EMTA) dimensions and weight Table 11 Dimensions and weight of Flexi Module Casing (EMHA) and Table 12 Dimensions and weight of Flexi Module Casing (EMTA) lists the dimensions and weight for the EMxA. Property

Value

Height

133 mm (3U) (5.2 in.)

Width

492 mm (19.4 in.)

Depth

560 mm (22.1 in.)

Weight

3.7 kg (8.2 lbs)

Table 11

Dimensions and weight of Flexi Module Casing (EMHA)

Property

Value

Height

90 mm (2U) (3.5 in.)

Width

492 mm (19.4 in.)

Depth

560 mm (22.1 in.)

Weight

3.2 kg (7 lb)

Table 12

DN09142347

Dimensions and weight of Flexi Module Casing (EMTA)

Id:0900d805809c0086 Confidential

33

Flexi Mounting Shield 3U Casing (FMSC) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

9 Flexi Mounting Shield 3U Casing (FMSC) description This section describes the following hardware: •

Flexi Mounting Shield 3U Casing (FMSC) 472820A

Figure 20

Flexi Mounting Shield 3U Casing (FMSC)

Flexi Mounting Shield 3U Casing (FMSC) is a standard 3U-high casing optimised for indoor stack installations. It is intended for RF Modules that are delivered without a casing. See Appendix Casing and cover kits need for Flexi Multiradio units for details. For the delivery contents of Flexi Mounting Shield 3U Casing, see Contents of the Flexi Mounting Shield 3U Casing (FMSC) delivery.

34

Id:0900d805809c18d9 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA/B) description

10 Flexi Power Module (FPMA) and submodules (FPAA and FPBA/B) description 10.1

Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA/FPBB) operation This section describes the following hardware: • •

Flexi Power Module (FPMA) 470139A Sub-modules: • Flexi Power AC/DC sub-module 200-240 V AC (FPAA) 470140A • Flexi Power Battery sub-module (FPBA) 470141A • Flexi Power Battery sub-module (FPBB) 472113A

Type label Figure 21

DN09142347

Flexi Power Module (FPMA)

Id:0900d805809c3bd2 Confidential

35

Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA/B) description

Figure 22

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Module (FPMA) with a full configuration of two FPAAs and two FPBAs

Flexi Power Module (FPMA) is an optional module consisting of FPMA mechanics and AC and DC interfaces. It takes up to four sub-modules (Flexi Power AC/DC sub-module 200-240 V AC and Flexi Power Battery sub-module (FPBA/FPBB), which can be chained together with an alarm cable. For installation instructions, see section Installing Flexi Power Module (FPMA) in the Installing Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items document. The FPMA can support 1-phase and 3-phase AC input. The nominal input voltage is 200-240 V AC (the operating voltage range is 180 - 276 V AC). The maximum output power from the FPMA is 4kW (with 4 FPAAs). There are following AC connection alternatives: • • • •

Single phase connection 230 V AC 3-phase star connection 230 V AC 3-phase delta connection, base voltage 100-120 V AC 3-phase delta connection 110 V AC

Flexi Power Module version 470139A.204 provides support for parallel operation of two FPMA modules in stack installations as well as Surge Protection Device (SPD) installation inside the AC connection box. The SPD is installed on a DIN rail with screws included in the FPMA delivery. Surge Protection Devices are recommended for outdoor conditions. Flexi Power AC/DC sub-module (FPAA) The main function of the FPAA is to provide the BTS with nominal 48 V DC power from an AC supply. Maximum DC output power of one FPAA module is 1000 W. A nominal 48 V DC supply is intended for BTS internal use only (a nominal 48 V DC supply is not intended for third-party equipment because they might require lower conducted emission level than EN55022 Class A). The FPAA includes its own integrated self-controlled fan. In case the fan fails, an alarm is generated and the FPAA has to be replaced (the fan alone cannot be replaced).

36

Id:0900d805809c3bd2 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Module (FPMA) and sub-modules (FPAA and FPBA/B) description

Flexi Multiradio AC/DC sub-module FPAA version 470140A.204 provides higher efficiency than FPAA version 470140A.101 – 102. Typical efficiency of FPAA version 470140A.204 is 95% @ 230VAC with the 40 – 90% load. Fan air flow direction of FPAA version 470140A.204 can be changed from back-to-front (factory default) to front-to-back in case when FPAA and FPMA is installed to a thirdparty cabinet. FPAA version 470140A.204 dust protection level has been increased from IP55 to IP65.

f Risk of thermal runaway of the battery, because temperature compensation of charging voltage is not supported. Do not connect an external lead acid battery for longer backup times to a nominal 48 V DC supply. Flexi Power Battery sub-module (FPBA/FPBB) The Flexi Power Battery sub-module (FPBA/FPBB) is a separate optional sub-module used together with the FPAA. The FPBA/FPBB provides short-term battery backup time when the AC power mains is down on a Flexi BTS site. The FPBA is a Lithium Ion battery and the FPBB is a Lithium Ferrite battery. The maximum DC output power from one FPBA/FPBB module is 1000 W. The input power for the BTS cannot exceed the maximum output power of the installed batteries. Otherwise the batteries do not provide the BTS with the needed power during power failure.

g

DN09142347

Do not install the FPBA and FPBB in parallel. If used in parallel, one of these two battery types is to be discharged faster than the other causing an unbalance between the batteries.

Id:0900d805809c3bd2 Confidential

37

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

10.2

Flexi Power Module (FPMA) dimensions and weight Table 13 Dimensions and weight of the FPMA lists the dimensions and weight for Flexi Power Module (FPMA). Property

FPMA

Height

133 mm/3 U (5.2 in.)

Width

447 mm (17.6 in.)

Depth without covers

422 mm (16.6 in.)

Depth with covers

560 mm (22.1 in.)

Weight (empty)

7.3 kg (16 lb)

Weight

22.4 kg

(fully equipped with one AC/DC power module and batteries)

(49.4 lb)

Table 13

38

Dimensions and weight of the FPMA

Id:0900d805809eca8e Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

10.3

Flexi Power Module (FPMA) and sub-module (FPAA and FPBA/FPBB) interfaces Flexi Power Module (FPMA) front panel connectors The connectors on the FPMA front panel, their types and purposes are listed in Table 14 Flexi Power Module (FPMA) front panel connectors, types and purposes. Connector

Type

Purpose

Power supply in

Terminal block

AC main power supply in

Power supply out

2-wire DC cable 4 x multibeam

DC feed to the BTS

Grounding

2 x M5

Module grounding

Table 14

Flexi Power Module (FPMA) front panel connectors, types and purposes

Flexi Power AC/DC sub-module (FPAA) front panel connectors There is a stand-by switch on the front panel of the FPAA. The stand-by switch is used for switching the FPAA unit ON/stand-by. The connectors on the FPAA front panel, their types and purposes are listed in Table 15 Flexi Power AC/DC sub-module (FPAA) front panel connectors, types and purposes. Connector

Type

Purpose

AC cable connector

Mate-N-Lock

AC input

DC connector

Multi-beam power supply connector

DC output

Alarm connector

2 x RJ-45*

Alarms**

Operational state visual indi- tri-color LED cation

Table 15

FPAA state or alarm indication

Flexi Power AC/DC sub-module (FPAA) front panel connectors, types and purposes

*for chaining **Alarm 1 (AL01): AC input failure (alarm is sent when AC input voltage is missing or it is out of range). **Alarm 2 (AL02): maintenance needed (possible reasons are unit failure, cooling fan failure, output power is low or over temperature shut down is ON). Flexi Power Battery sub-module (FPBA/FPBB) front panel connectors There is a stand-by switch on the front panel of the FPBA/B. The connectors on the FPBA/B front panel, their types and purposes are listed in Table 16 Flexi Power Battery sub-module (FPBA/FPBB) front panel connectors, types and purposes.

DN09142347

Id:0900d805809d1c34 Confidential

39

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Connector

Type

Purpose

DC input/output connector

Multi-beam power supply connector

DC input and output

Alarm connector

2 x RJ-45*

Alarms**

Operational state visual indication

tri-color LED

FPBA/B state or alarm indication

Table 16

Flexi Power Battery sub-module (FPBA/FPBB) front panel connectors, types and purposes

*for chaining **Alarm 2 (AL02): maintenance needed (possible reasons are unit failure, output power is low or unit has reached end of its life). **Unit has an input for Alarm 1 (AL01) from FPAA unit (Alarm 1 is a trigger for battery discharging).

40

Id:0900d805809d1c34 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

10.4

Flexi power sub-module (FPAA and FPBA/FPBB) LED indications FPAA LED indications The FPAA LED indications are explained in Table 17 FPAA LED indications. Read the information on LED indications thoroughly. A blinking red LED does not always require removing the module. Color

Explanation

Yellow

Stand-by (AC connected)

Green

Normal operation

Red

Alarm or fault

Red, blinking

Unit operating with abnormal input voltage

Table 17

FPAA LED indications

See Figure 23 FPAA LED for the location of the FPAA LED.

LED

DN70350654

Figure 23

FPAA LED

FPBA/B LED indications The FPBA/B LED indications are explained in Table 18 FPBA/B LED indications. Color

Explanation

Yellow

Stand-by (DC connected from FPAA)

Green

Normal operation, battery OK

Green, blinking slowly

Charging

Green, blinking fast

Discharging

Blinking fast between green and yellow

Forced discharge mode

Red, blinking fast

Minor alarm

Red

Major alarm or fault

Table 18

FPBA/B LED indications

The LED's slow blinking frequency is 1 Hz (1 sec) and fast blinking frequency 2 Hz (0.5 sec).

DN09142347

Id:0900d805809d1c4a Confidential

41

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

See Figure 24 FPBA/B LED for the location of the FPBA/B LED.

LED

Figure 24

42

FPBA/B LED

Id:0900d805809d1c4a Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power DC/DC Module (FPDA) description

11 Flexi Power DC/DC Module (FPDA) description 11.1

Flexi Power DC/DC Module (FPDA) operation This section describes the following hardware •

Flexi Power DC/DC Module (FPDA) 470067A

Figure 25

Flexi Power DC/DC Module (FPDA)

Flexi Power DC/DC Module (FPDA) is an optional stand-alone 2 kW DC/DC module. When the BTS power load is more than 2 kW, multiple FPDAs can be installed in parallel. When FPDAs are used in parallel, a maximum of two DC cables can be installed together at each output terminal. Conducted emission level of the 53-55 V DC supply is according to the standard EN55022 Class A. The 53-55 V DC supply is intended for BTS internal use only (the 5355 V DC supply is not intended for third-party equipment because they might require lower conducted emission level than EN55022 Class A).

f

CAUTION! Risk of equipment damage. Risk of thermal runaway of the battery, because temperature compensation of charging voltage is not supported. Do not connect an external lead acid battery for longer backup times to the 53-55 V DC supply.

The FPDA includes its own integrated self-controlled fan. In case the fan fails, an alarm is generated and the fan has to be replaced. For installation instructions, see section Installing Flexi Power DC/DC Module 24V FPDA in the Installing Flexi Multiradio BTS and Flexi Multiradio 10 BTS Optional Items document.

DN09142347

Id:0900d805809c9709 Confidential

43

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

11.2

Flexi Power DC/DC Module (FPDA) dimensions and weight Table 19 Dimensions and weight of the FPDA lists the dimensions and weight for the FPDA. Property

Value

Height

90 mm (2U) (3.5 in.)

Width

447 mm (17.6 in.)

Depth without covers

422 mm (16.6 in.)

Depth with covers

560 mm (22.1 in.)

Weight

< 15 kg (< 33.1 lbs)

Table 19

44

Dimensions and weight of the FPDA

Id:0900d8058099ac8b Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

11.3

Flexi Power DC/DC Module (FPDA) interfaces There is a stand-by switch on the front panel of the FPDA. The connectors on the FPDA front panel, their types and purposes are listed in Table 20 FPDA front panel connectors, connector types and purposes. Connector

Connector type

Purpose

Input connector

M10 bolts

DC input

Output connector

M10 bolts

DC output

Alarm connectors

2 x RJ-45*

Alarms**

Table 20

FPDA front panel connectors, connector types and purposes

*for chaining **Alarm 1 (AL01): DC input failure (alarm is sent when DC input voltage is missing or it is out of range). **Alarm 2 (AL02): maintenance needed (possible reasons are unit failure, cooling fan failure, output power is low or over temperature shut down is ON). The FPDA front panel is presented in Figure 26 Front panel of the FPDA.

DC Input cabling

Alarm cabling

DC Output cabling

LED

GND Figure 26

DN09142347

Front panel of the FPDA

Id:0900d805809c972f Confidential

45

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

11.4

Flexi Power DC/DC Module (FPDA) LED indications The FPDA has a tri-color LED on the front panel to indicate the operational status of the module and all fault conditions during operation. Read the information on LED indications thoroughly. A blinking red LED does not always require removing the module. The LED indications of the FPDA are listed and explained in Table 21 FPDA LED indications. Color

Explanation

Green

Normal operation

Red

Alarm or fault

Yellow

Stand-by

Red, blinking

Abnormal input voltage

Table 21

46

FPDA LED indications

Id:0900d8058099acff Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Rectifier (FPRA) description

12 Flexi Power Rectifier (FPRA) description This section describes the following hardware: •

12.1

Flexi Rectifier Module (FPRA) CS7000000

Flexi Power Rectifier (FPRA) operation Flexi Rectifier Module (FPRA) is a modular 6kW output power AC rectifier package made up of three individual 2kW AC/DC power modules operating in a parallel mode configuration. The FPRA outputs a positive earthed –54VDC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. It also includes a Power Distribution Assembly (PDA), which has a fully integrated battery protection LVD, load/battery circuit breakers, battery current shunt and alarm signals to the BTS EAC interface. It supports Flexi BTS configurations in indoor and outdoor cabinets, and stack, pole and wall configurations. The FPRA comprises of one PDA and one to three identical 2kW rectifiers working in a parallel mode. The FPRA has the following properties: •

•

•

•

•

•

12.2

High-integrated power system. The FPRA integrates the rectifiers, the AC and DC distribution, as well as supervisor and communication functions. Modularized design. The modularized design of the FPRA leads to easier installation, maintenance and troubleshooting. Flexible applications. The FPRA supplies the user with a varied output power of 2/4/6kW by means of installing one to three rectifier modules. Also the three battery back-up channels and two load channels of the FPRA provides the user with flexible battery and load applications. Variable AC power connections. The FPRA can be used with different AC power types by means of reconfiguring the internal AC terminal block. Easy to control. The user can control and supervise the operation of the FPRA via the GUI after connecting the FPRA to a user PC. IP54/55 The FPRA is IP54 rated and IP55 rated when fitted with front and rear covers.

Flexi Power Rectifier (FPRA) dimensions See Table 22 Flexi Power Rectifier (FPRA) dimensions for the dimensions of the Flexi Power Rectifier (FPRA). Property

Value

Height

128.7 mm (5.1 in.)

Table 22

DN09142347

Flexi Power Rectifier (FPRA) dimensions

Id:0900d805809d1c8c Confidential

47

Flexi Power Rectifier (FPRA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Property

Value

Width

475 mm (18.7 in.)

Depth

504 mm (19.8 in.)

Table 22

48

Flexi Power Rectifier (FPRA) dimensions (Cont.)

Id:0900d805809d1c8c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power AC/DC Submodule 230V (FPAC) description

13 Flexi Power AC/DC Submodule 230V (FPAC) description This section describes the following hardware: •

Flexi Power AC/DC Submodule 230V (FPAC) 472438A

Flexi Power AC/DC Submodule 230V (FPAC) is a standalone 500W AC/DC power supply for all Flexi 2TX Remote Radio Heads (RRH). Its AC input range is from 90 to 276 VAC with 55 VDC output. The FPAC is IP65-rated. There are following installation options for Flexi Power AC/DC Submodule 230V (FPAC): • • •

g 13.1

Pole installation using Flexi Pole Mounting Kit (FPKA/FPKC) (FPAC installed between the pole and RRH) Pole installation using any commercial fixing brackets (for example, jubilee clips or cable ties) Wall installation (no mounting kit needed)

FPAC must be installed in vertical position in order to allow efficient natural convection cooling.

Flexi Power AC/DC Submodule 230V (FPAC) dimensions and weight See Table 23 Flexi Power AC/DC Submodule 230V (FPAC) dimensions for the dimensions and weight of the FPAC. Property Height

Value 300 mm (11.8 in.)

Width

120 mm (4.7 in.)

Depth

75 mm (3.0 in.)

Volume

2.7 liters

Weight

3 kg (6.6 lb)

Table 23

13.2

Flexi Power AC/DC Submodule 230V (FPAC) dimensions

Flexi Power AC/DC Submodule 230V (FPAC) LED indications A multicolored LED is located on the front panel of the FPAC. The LED provides the following indications:

DN09142347

Id:0900d805809d1c98 Confidential

49

Flexi Power AC/DC Submodule 230V (FPAC) description

Color

Function of the unit

Orange

Stand-by

Green

Normal operation

Red

Fault

Table 24

50

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Fault caused by

No output (Mains break, high internal temperature, OCP, OVP, UVP)

Flexi Power AC/DC Submodule 230V (FPAC) LED indications

Id:0900d805809d1c98 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power AC/DC Submodule 230V (FPAD) description

14 Flexi Power AC/DC Submodule 230V (FPAD) description This section describes the following hardware: •

Flexi Power AC/DC Submodule 230V (FPAD) 472805A

Flexi Power AC/DC Submodule 230V (FPAD) 472805A is a standalone 650W AC/DC power supply for all Flexi 2TX Remote Radio Heads (RRH). Its AC input range is from 100 to 240 VAC with 55 VDC output. The FPAD is IP65-rated. There are following installation options for Flexi Power AC/DC Submodule 230V (FPAD): • • •

g 14.1

Pole installation using Flexi Pole Mounting Kit (FPKA/FPKC) (FPAD installed between the pole and RRH) Pole installation using any commercial fixing brackets (for example, jubilee clips or cable ties) Wall installation (no mounting kit needed)

FPAD must be installed in vertical position in order to allow efficient natural convection cooling.

Flexi Power AC/DC Submodule 230V (FPAD) dimensions and weight See Table 25 Flexi Power AC/DC Submodule 230V (FPAD) dimensions for the dimensions and weight of the FPAD. Property Height

Value 300 mm (11.8 in.)

Width

120 mm (4.7 in.)

Depth

75 mm (3.0 in.)

Volume

2.7 liters

Weight

3 kg (6.6 lb)

Table 25

14.2

Flexi Power AC/DC Submodule 230V (FPAD) dimensions

Flexi Power AC/DC Submodule 230V (FPAD) LED indications A multicolored LED is located on the front panel of the FPAD. The LED provides the following indications:

DN09142347

Id:0900d805809d1c9c Confidential

51

Flexi Power AC/DC Submodule 230V (FPAD) description

Color

Function of the unit

Orange

Stand-by

Green

Normal operation

Red

Fault

Table 26

52

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Fault caused by

No output (Mains break, high internal temperature, OCP, OVP, UVP)

Flexi Power AC/DC Submodule 230V (FPAD) LED indications

Id:0900d805809d1c9c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Distribution and Fuses (FPFB) description

15 Flexi Power Distribution and Fuses (FPFB) description This section describes the following hardware: •

Flexi Power Distribution and Fuses (FPFB) 084175A

Figure 27

Flexi Power Distribution and Fuses (FPFB)

Flexi Power Distribution and Fuses (FPFB) is a power distribution unit with overcurrent protection for the outputs. FPFB distributes nominal -48.0 VDC, also referred to as V48N, to System Module, maximum two System Extension Modules, three RF Modules and two fans. FPFB is compatible with System Module variants FSMB, FSMC, FSMD and FSME. System Module variant FSMB supports two System Extension Modules, whereas variants FSMC, FSMD and FSME support one System Extension Module. FPFB includes also LEDs for output status indications and operating switches for outputs. The protection class of the FPFB is IP65.

15.1

Flexi Power Distribution and Fuses (FPFB) operation Flexi Power Distribution and Fuses (FPFB) provides following functions • • • • • • • • • • • • • • •

DN09142347

Input power connections on the side of FPFB Four output connections on the front panel of FPFB One output connection at the bottom of FPFB One fan connector for two fans at the back of FPFB Dedicated membrane switch for every RF Module Dedicated membrane switch for System Extension Module Common membrane switch for System Module and fan outputs Surge protection for input lines Reverse voltage protection Over Current Protection (OCP) for outputs 1-5 Automatic reset of fuses or overcurrent protections for fan outputs (output 6) Over Temperature Protection (OTP) Inrush current limiter Led indication at the front panel for outputs 1-5 Remote output OFF/ON control for outputs 1-5 through System Module

Id:0900d805809d1ca2 Confidential

53

Flexi Power Distribution and Fuses (FPFB) description

15.2

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Distribution and Fuses (FPFB) dimensions and weight The dimensions of the FPFB are presented in Table 27 Flexi Power Distribution and Fuses (FPFB) dimensions. Property

FPFB

Width

190 mm (7.48 in.)

Height

48.6 mm (1.91 in.)

Depth

289 mm (11.38 in.)

Table 27

54

Flexi Power Distribution and Fuses (FPFB) dimensions

Id:0900d805809d1ca2 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Distribution and Fuses Outdoor (FPFC) description

16 Flexi Power Distribution and Fuses Outdoor (FPFC) description This section describes the following hardware: •

Flexi Power Distribution and Fuses Outdoor (FPFC) 472508A

FPFC

Input connector IP boot Figure 28

EAC connector

Input connector

On/Off Bar

Output connector IP boot

Flexi Power Distribution and Fuses Outdoor (FPFC)

Flexi Power Distribution and Fuses Outdoor (FPFC) is a standalone 19-inch wide outdoor general purpose Power Distribution Unit (PDU) with Class II Over Voltage Protection and 15 kA protection level. It feeds DC power to Flexi RF Modules, Remote Radio Heads or microwave equipment without an external protection unit (FSEC or FSES), when FPFC is installed close to RF Module(s) or RRH(s) or MW (maximum 4 m (13.12 ft) away). FPFC provides six outlets for Flexi Modules (RF Modules or RRHs or System Module) or any standard -48 V DC device at the site. It can also be used, for example, up in the tower to divide one main DC line to several RRHs or MW equipment in the mast. Flexi Power Distribution Outdoor unit includes input, output connectors and output fuses. Front cover, back cover and two pieces of cable entries together with a 2U casing provide UV protection.

16.1

Flexi Power Distribution and Fuses Outdoor (FPFC) operation The FPFC can be installed: • •

outdoors with EMTA Mechanical 2U Unit (470315A) to support wall/pole/cabinet/plinth mounting indoors with EMTA Mechanical 2U Unit (470315A) or a standard cabinet

The FPFC provides the following features: • • • •

DN09142347

Input power range: 36~57.5 VDC, max output current 180A Output power voltage: 36~57.5 VDC Output current: channel 1~2 30A fuse. Channel 3~6 adjustable 4A/15A/30A fuse. Max 30kA input OVP protection integrated with SPD alarm.

Id:0900d805809d1cb4 Confidential

55

Flexi Power Distribution and Fuses Outdoor (FPFC) description

• •

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Output on/off can be controlled by breaker bars on the front panel. 2 alarm signals (NO & NC) to indicate SPD status: – Normal open connection: 5V alarm detection line is pulled down during alarm: Active = 0, Inactive = 1. – Normal close connection: 5V alarm detection line is pulled up during alarm: Active = 1, Inactive = 0.

In case the protective components have been damaged by the surge pulse, an alarm can be detected from FPFC. The alarm connection is Normally Open - an alarm is raised when connection becomes Closed. The complete FPFC needs to be replaced with a new one in order to protect the power feeding lines again. The damage of the protective component does not turn off the power feeding between the modules.

56

Id:0900d805809d1cb4 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

16.2

Flexi Power Distribution and Fuses Outdoor (FPFC) description

Flexi Power Distribution and Fuses Outdoor (FPFC) dimensions and weight The dimensions and weight of the FPFC are presented in Table 28 Flexi Power Distribution and Fuses Outdoor (FPFC) dimensions and weight. Property

FPFC

Width

482.5 mm (19 in.)

Height

75 mm (2.95 in.)

Depth

267 mm (10.51 in.)

Weight

5.5 kg (12.1 lbs)

Table 28

DN09142347

Flexi Power Distribution and Fuses Outdoor (FPFC) dimensions and weight

Id:0900d805809d1cb4 Confidential

57

Flexi Power Distribution Sub-Module (FPFD) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

17 Flexi Power Distribution Sub-Module (FPFD) description This section describes the following hardware: •

Flexi Power Distribution Sub-Module (FPFD) 472301A

Figure 29

Flexi Power Distribution Sub-Module (FPFD)

Flexi Power Distribution Sub-Module (FPFD) is a highly integrated optional size-optimized power distribution unit (PDU) for System Module variants FSMF/G/L. It is installed in the top left slot of the System Module. The FPFD has integrated basic Over Voltage Protection (OVP Type approval level with 2kV/1kV), EMC filtering and reverse polarity protection. It is IP65 rated.

17.1

Flexi Power Distribution Sub-Module (FPFD) operation Flexi Power Distribution Sub-Module (FPFD) can be used for stacked and feederless configurations in the same way as earlier integrated Flexi PDUs. In feederless configurations, FPFD can be used with optional Over Voltage Protection units (FSEC or FSES). Flexi Power Distribution Sub-Module (FPFD) provides four external -48 V DC outputs for Flexi Modules (RF Module, RRH, or external System Module) or any standard 48 V DC device at the site, and one internal DC output to System Module itself. The FPFD provides the following external interfaces: • • • • •

58

One -48 V DC input Four external -48 V DC outputs One internal DC output to the System Module ON/OFF switches Status LEDs at the front panel

Id:0900d805809a249c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Distribution and Fuses Indoor (FPFI) description

18 Flexi Power Distribution and Fuses Indoor (FPFI) description This section describes the following hardware: •

Flexi Power Distribution and Fuses Indoor (FPFI) 472394A

Figure 30

Flexi Power Distribution and Fuses Indoor (FPFI)

Flexi Power Distribution and Fuses Indoor (FPFI) is capable of distributing nominal -48.0 VDC to two Flexi Multiradio System Modules, three RF Modules, two Line Terminal Equipments (LTE) and to the cabinet fan. The distributed voltage complies with ETS 300 132-2.

18.1

Flexi Power Distribution and Fuses Indoor (FPFI) operation The FPFI provides the following features: • • • • •

input screw terminals on the front panel eight output screw terminals on the front panel class tube fuses for Line Terminal Units (LTE1 and LTE2 outputs) overvoltage protection 2 x M5 unit grounding interface on the front panel

The FPFI unit includes input and outputs connectors together with output fuses. It can be installed either horizontally or vertically. FPFI interfaces are shown in Figure 31 Flexi Power Distribution and Fuses Indoor (FPFI) front panel.

Figure 31

Flexi Power Distribution and Fuses Indoor (FPFI) front panel

In case the protective components have been damaged by the surge pulse, an alarm can be detected from FPFI. The alarm connection is Normally Open - an alarm is raised when connection becomes Closed. The complete FPFI needs to be replaced with a new one in order to protect the power feeding lines again. The damage of the protective component does not turn off the power feeding between the modules.

DN09142347

Id:0900d805809d0e30 Confidential

59

Flexi Power Distribution and Fuses Indoor (FPFI) description

18.2

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Power Distribution and Fuses Indoor (FPFI) dimensions Flexi Power Distribution and Fuses Indoor (FPFI) is 1U high and 19 inches wide. It contains fixing points to a 19-inch fixing system. The dimensions of the FPFI are presented in Table 29 Flexi Power Distribution and Fuses Indoor (FPFI) dimensions. Property

FPFI

Height

1U (~44 mm/~1.75 in)

Width

482.6 mm (19 in.)

Depth

max. 80 mm (max. 3.15 in.)

Table 29

60

Flexi Power Distribution and Fuses Indoor (FPFI) dimensions

Id:0900d805809d0e30 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSEC) description

19 Flexi System External OVP (FSEC) description This section describes the following hardware: •

Flexi System External OVP (FSEC) 471397A

DN70154491 Figure 32

Flexi System External OVP (FSEC)

Flexi System External OVP (FSEC) protects Flexi sub-modules against surge pulse(s) in power feeding lines. It is also used to provide power to the Flexi Site Support Module (FCSA), and for altering the DC cable diameter. It does not require regular maintenance.

19.1

Flexi System External OVP (FSEC) operation The FSEC gives SPD Class II (C, T2) surge protection 15 kA for DC power feed and provides IP55 protection. It is used in both ends of the long DC feeder line, but not at the input of a System Module. It gives: • •

protection level UP (differential, that is line – line) < 500 V (at In, 8/20 microseconds) protection level UP (common, that is line – ground) < 1000 V (at In, 8/20 microseconds)

The FSEC can be installed: • • • •

on the roof of Flexi Cabinet for Indoor (FCIA) on the roof of Flexi Cabinet for Outdoor (FCOA) on Flexi Mounting Auxiliary Bracket (FMAA) on Flexi Pole Kit (FPIA) (471767A.202 or newer)

There are five versions of the FSEC, which are separated from each other by the first two digits of the factory code: • • • • •

DN09142347

6Yxxxxxxxxx E4xxxxxxxxx S1xxxxxxxxx M2xxxxxxxxx V5xxxxxxxxx

Id:0900d805809c2b3c Confidential

61

Flexi System External OVP (FSEC) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

In case the protective components have been damaged by the surge pulse, an alarm can be detected from FSEC. The alarm connection is Normally Open - an alarm is raised when connection becomes Closed. The OVP module inside the FSEC is replaceable and needs to be replaced with a new one in order to protect the power feeding lines again. The damage of the protective component does not turn off the power feeding between the modules. For installation instructions, see section Installing Flexi System External OVP (FSEC) in the Installing Flexi Multiradio BTS and Flexi Multiradio 10 BTS Optional Items document. See Figure 33 FSEC internal wiring (version 6Yxxxxxxxxx) for the internal and Figure 34 FSEC external wiring (version 6Yxxxxxxxxx) for the external wiring of the FSEC.

Internal wiring (factory cabling) version 6Yxxxxxxxxx FSEC

VAL-MS VAL-MS 60 ST 60 ST

+

+

PE

-

-

PE

PE terminals are electrically connected to DIN rail

Electrical connection GND

PE

0V (+)

-48 V DN70592401

Figure 33

62

FSEC internal wiring (version 6Yxxxxxxxxx)

Id:0900d805809c2b3c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSEC) description

External wiring, version 6Yxxxxxxxxx FSEC

VAL-MS VAL-MS 60 ST 60 ST

+ +

PE

-

-

PE

Cable shield

Ground cable to plinth or site grounding bar

DC cable type: MCCMK/MCMK (or equivalent)

System/RF Module To another FSEC

Figure 34

DN09142347

FSEC external wiring (version 6Yxxxxxxxxx)

Id:0900d805809c2b3c Confidential

63

Flexi System External OVP (FSEC) description

19.2

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSEC) dimensions and weight The dimensions and weight of Flexi System External OVP (FSEC) are presented in this section. Property

FSEC

Width

95 mm (3.7 in.)

Height

155 mm (6.1 in.)

Depth

155 mm (6.1 in.)

Weight

2.7 kg (5.9 lb)

Table 30

64

Flexi System External OVP (FSEC) dimensions and weight

Id:0900d805809c2b3c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

19.3

Flexi System External OVP (FSEC) description

Flexi System External OVP (FSEC) interfaces In the FSEC, there are screw terminals for input and output cables. There are four pieces of screw terminals for AWG 2 cables and for earthing two PEs (protective earthing GND) terminals for AWG 2 cable size. A 2-meter DC cable is included in the FSEC delivery. See Table 31 Allowed cable thicknesses for Flexi System External OVP (FSEC) for the allowed cable thickness of FSEC. Interface type

Cable thickness

DC feeder

max. 35 mm2

Alarm

max. 2.5 mm2

Table 31

DN09142347

Allowed cable thicknesses for Flexi System External OVP (FSEC)

Id:0900d805809c2b3c Confidential

65

Flexi System External OVP (FSEC) description

19.4

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSEC) LED indications See Table 32 FSEC E4xxxxxxxxx and S1/M2/V5xxxxxxxxx LED indications for the FSEC LED indications. LED

Status

Green/On

Overvoltage protection OK.

Red/Off

Overvoltage protection tripped. Module needs replacing.

Table 32

66

FSEC E4xxxxxxxxx and S1/M2/V5xxxxxxxxx LED indications

Id:0900d805809c2b3c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSES) description

20 Flexi System External OVP (FSES) description This section describes the following hardware: •

Flexi System External OVP (FSES) 472285A

Figure 35

Flexi System External OVP (FSES)

Flexi System External OVP (FSES) protects Flexi sub-modules against surge pulse(s) in power feeding lines. It is also used to provide power to the Flexi Site Support Module (FCSA), and for altering the DC cable diameter. It does not require regular maintenance.

DN09142347

Id:0900d805809d1d38 Confidential

67

Flexi System External OVP (FSES) description

20.1

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSES) operation The FSES gives SPD Class II (C, T2) surge protection 15 kA for DC power feed and provides IP65 protection. It is used in both ends of the long DC feeder line, but not at the input of a System Module. It gives: • •

protection level UP (differential, that is line – line) < 500 V (at In, 8/20 microseconds) protection level UP (common, that is line – ground) < 1000 V (at In, 8/20 microseconds)

The FSES can be installed: • • • •

on the side of a 3U casing on the roof of Flexi Cabinet for Indoor (FCIA) on the roof of Flexi Cabinet for Outdoor (FCOA) on Flexi Pole Kit (FPIA)

In case the protective components have been damaged by the surge pulse, an alarm can be detected from FSES. The alarm connection is Normally Open - an alarm is raised when connection becomes Closed. Complete FSES need to be replaced with a new one in order to protect the power feeding lines again. The damage of the protective component does not turn off the power feeding between the modules. Maximum output current for the FSES is 30A DC.

68

Id:0900d805809d1d38 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

20.2

Flexi System External OVP (FSES) description

Flexi System External OVP (FSES) dimensions and weight The dimensions and weight of Flexi System External OVP (FSES) are presented in this section.

DN09142347

Id:0900d805809d1d38 Confidential

69

Flexi System External OVP (FSES) description

20.3

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External OVP (FSES) interfaces In the FSES, there are following electrical interfaces: • • • •

DC output/input with pre installed cable including Multibeam connector DC feeder interface with three pole screw terminal grounding interface with pre installed cable alarm interface with two pole screw terminal

IP Boots for the DC and alarm interfaces are delivered together with FSES. See Figure 36 Flexi System External OVP (FSES) interfaces for the external interfaces of the FSES.

Alarm interface DC output/input

Figure 36

DC output/input Grounding

Flexi System External OVP (FSES) interfaces

See Table 33 Allowed cable thicknesses for Flexi System External OVP (FSES) for the allowed cable thickness of FSES. Interface type

Cable thickness

DC feeder

max. 25 mm2

Alarm

max. 2.5 mm2

Table 33

70

Allowed cable thicknesses for Flexi System External OVP (FSES)

Id:0900d805809d1d38 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Fiber Optical Distribution Unit (FODA) description

21 Flexi Fiber Optical Distribution Unit (FODA) description This section describes the following hardware: •

Flexi Fiber Optical Distribution Unit (FODA) 472606A

Cable gland

OPT1-3

OPT4-5 OPT6

OPT7 OPT8-9

OPT10-12

Cable gland optional Figure 37

21.1

Flexi Fiber Optical Distribution Unit (FODA)

Flexi Fiber Optical Distribution Unit (FODA) operation Flexi Fiber Optical Distribution Unit (FODA) is a stand-alone outdoor product which can be used for cable routing between the RF Module and System Module. Together with the combination of jumper cables and different length of feeder cables, it simplifies site installation. FODA provides up to 12 outputs for RF Modules or RRHs. FODA supports different installation options with mounting brackets. It can be assembled to a 3U casing together with the 2U PDU. It can also be mounted directly on a pole/mast or wall.

21.2

Flexi Fiber Optical Distribution Unit (FODA) dimensions Flexi Fiber Optical Distribution Unit (FODA) is 1U high and 19 inches wide. It contains fixing points to a 19-inch fixing system. FODA dimensions are presented in Table 34 Flexi Fiber Optical Distribution Unit (FODA) dimensions. Property

FODA

Height

1U (max. ~45.7 mm/~1.75 in)

Width

482.6 mm (19 in.)

Table 34

DN09142347

Flexi Fiber Optical Distribution Unit (FODA) dimensions

Id:0900d805809d1e2c Confidential

71

Flexi Fiber Optical Distribution Unit (FODA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Property

FODA

Depth

max. 200 mm (max. 7.87 in.)

Table 34

72

Flexi Fiber Optical Distribution Unit (FODA) dimensions (Cont.)

Id:0900d805809d1e2c Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi System External Alarm (FSEB) description

22 Flexi System External Alarm (FSEB) description 22.1

Flexi System External Alarm (FSEB) operation This section describes the following hardware: •

Flexi System External Alarm (FSEB) 471424A

ESD

Grounding point EAC M16 UltraSite and Talk swap cases BTS interconnection cable DN70283679

Figure 38

Flexi System External Alarm (FSEB)

The optional Flexi System External Alarm Module (FSEB) provides IP65 protected screw terminals (up to 24 for alarm inputs and 6 for control outputs) and power for the Flexi Cabinet Fire Detector (FCDA). The number of supported alarms depends on the mode used (12 alarms versus 24 alarms mode with jumper X1103). System Module variant

Alarms supported

ESMA, ESMB, ESMC

24

FSMC, FSMD, FSME (WCDMA)

24

FSMD, FSME (LTE)

12

FSMF, FSMG, FSML

12

Table 35

Requirements

FSEB v.304 WN6.0 MP3 or later

Alarms supported by System Module variants

The FSEB can be installed in the following ways: • •

DN09142347

On a wall (vertical or horizontal position) On a pole using Flexi Pole Installation Kit (FPIA)

Id:0900d805809c2b48 Confidential

73

Flexi System External Alarm (FSEB) description

• • •

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

On a module casing in pole, wall, or stack installations using Flexi Mounting Auxiliary Brackets (FMAA) On the Flexi Cabinet for Indoor (FCIA) or Flexi Cabinet for Outdoor (FCOA) roof (horizontal position only) In Citytalk cabinets, the FSEB can be installed on top of the stack (depending on working space) or outside of the cabinet. The box cannot be installed on the roof.

If there is not enough space left for the FSEB or other auxiliary boxes on the FCIA, FCOA, or the FMAA, the additional auxiliary box(es) must be installed on a wall or pole close to the BTS. In stack, wall or pole installations, additional FMAA brackets can also be installed if there are multiple plinths. Note that the distance from each box to the BTS is limited by the lengths of the cables coming from the auxiliary box. For System Module variants FSMF/G/L, the EAC cable FTSI (472578A) is required between the System Module and FSEB. Flexi Mounting Auxiliary Brackets (FMAA) can be used to mount the FSEB on the top or outer casings in pole, wall, and stack configurations. The brackets are mounted on the top or outer casing using the existing connection pin holes. Flexi Pole Installation Kit (FPIA) can be utilized for pole installations.

74

Id:0900d805809c2b48 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

22.2

Flexi System External Alarm (FSEB) interfaces See Figure 39 FSEB interfaces for the FSEB mechanical interfaces:

ESD

Grounding point EAC M16 UltraSite and Talk swap cases BTS interconnection cable DN70283679

Figure 39

FSEB interfaces

PWB interface The PWB interface and connectors are presented in Table 36 Interface and connector overview. Interface

Type

EACX-I

Sub-D37, female

EACX-S

10 SMDK1/6-3.5

Description

• •

12 direct alarm inputs 6 alarm outputs (ESM extension, compatible to EAC on ESM)

60 pin screw terminal combines EACX-I, EACXII

Fire detector power supply

Screw terminal

DC power supply for the optional fire detector

ESM

Sub-D37, male

Interface to the System Module, *CAN bus

*EACX-II

Sub-D37, female

12 alarm inputs through CAN bus

Table 36

Interface and connector overview

*Not used in 12 Alarms mode. See Figure 40 FSEB PWB for the FSEB PWB.

DN09142347

Id:0900d8058099993a Confidential

75

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 40

76

FSEB PWB

Id:0900d8058099993a Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

22.3

Flexi System External Alarm (FSEB) dimensions and weight The dimensions and weight of the FSEB are presented in Table 37 Flexi System External Alarm (FSEB) dimensions and weight dimensions. Property

Value

Width

335 mm (13.2 in.)

Height

94 mm (3.7 in.)

Depth

182 mm (7.2 in.)

Weight

2 kg (4.4 lbs)

Table 37

Flexi System External Alarm (FSEB) dimensions and weight dimensions

The mounting dimensions of the FSEB enclosure are 110 mm x 324 mm (4.3 in. x 12.8 in.).

DN09142347

Id:0900d805809c2b4c Confidential

77

GPS Antenna Kit (FYGA) and GPS GLONASS Receiver Antenna (FYGB) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

23 GPS Antenna Kit (FYGA) and GPS GLONASS Receiver Antenna (FYGB) description This section describes the following hardware: • • • • •

GPS Antenna Kit (FYGA) 471442A GPS GLONASS Receiver Antenna (FYGB) 472748A GPS Mounting Kit (FYMA) 471605A Flexi GPS Surge Protector Kit (FYEA) 471822A Power/data cables: • GPS cable set (FYHA) up to 30 m 471606A • GPS cable set (FYHB) up to 100 m 471653A • GPS cable set (FTSE) up to 30 m 472510A (for System Module variants FSMF/G/L) • GPS cable set (FTSH) up to 100 m 472577A (for System Module variants FSMF/G/L)

Figure 41

GPS Antenna Kit (FYGA)/GPS GLONASS Receiver Antenna (FYGB)

Flexi Multiradio BTS uses GPS (Global Positioning System) or GNSS (Global Navigation Satellite System) as a source for frequency and time synchronization. A GPS or GLONASS antenna with an integrated receiver is installed outside for satellite visibility, and is directly connected to the System Module. DC power feed for the receiver is supplied through the combined power and data cable. Figure 42 FYGA/FYGB mounted on a pole using GPS Mounting Kit (FYMA) illustrates a pole-mounted antenna using GPS Mounting Kit (FYMA).

78

Id:0900d805809c0f77 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 42

GPS Antenna Kit (FYGA) and GPS GLONASS Receiver Antenna (FYGB) description

FYGA/FYGB mounted on a pole using GPS Mounting Kit (FYMA)

Flexi GPS Surge Protector Kit (FYEA) is available as an optional unit to protect the System Module from transient voltage and current spikes. It is installed to the GPS antenna line. The surge protector is particularly useful in locations with a high lightning risk.

Figure 43

Flexi GPS Surge Protector Kit (FYEA)

The GPS/GLONASS antenna is connected to the Sync In port on the System Module front panel.

DN09142347

Id:0900d805809c0f77 Confidential

79

GPS Antenna Kit (FYGA) and GPS GLONASS Receiver Antenna (FYGB) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Figure 44

Sync In port on the FSMC/D/E front panel (FYGA only)

Figure 45

Sync In port on the FSMF/G/L front panel

See Table 38 Technical details of FYGA/FYGB for the properties of FYGA/FYGB. Property Depth

Value 95 mm (3.74 in.)

Height

72.5 mm (2.85 in.)

Weight

154 g (5.4 oz)

Operating temperature

-40 to +85 Cº (-40 to 185 Fº)

Table 38

Technical details of FYGA/FYGB

Property Depth

Value 225 mm (8.86 in.)

Table 39

80

GPS Mounting Kit (FYMA) dimensions (antenna excluded)

Id:0900d805809c0f77 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

GPS Antenna Kit (FYGA) and GPS GLONASS Receiver Antenna (FYGB) description

Property Height

Value 260 mm (10.24 in.)

Table 39

GPS Mounting Kit (FYMA) dimensions (antenna excluded) (Cont.)

The synchronization using proceeds according to the following steps: 1. The System Module receives pps from the GPS/GNSS through Sync In. 2. The System Module generates a System Clock and a System Synchronization Burst. 3. The periodic Synchronization Burst, which contains air-interface-specific frame numbers and time references, provides time synchronization between BTSs to reduce interference. 4. The System Module forwards the System Clock and a System Synchronization Burst to the RF Module(s) through an optical interface. The DC power feed (12 V DC) for the receiver is supplied through combined power/data cables that are listed at the start of this chapter.

g

DN09142347

System Module contains an oven controlled oscillator (OCXO), which provides a highly stable clock even if the FYGA/FYGB fails or GPS/GLONASS signal is temporarily unavailable (Holdover functionality).

Id:0900d805809c0f77 Confidential

81

Flexi GPS Box (FYGD) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

24 Flexi GPS Box (FYGD) description This section describes the following hardware: •

24.1

Flexi GPS Box (FYGD) 472802A

Flexi GPS Box (FYGD) operation Flexi GPS Box (FYGD) is used for providing two synchronization resources, including GPS/GNSS Passive Antenna (Primary Source) and CMCC 1PPS+TOD (Backup Source), for Flexi BTS. It is installed inside Flexi System Module variants FMSF/G/L in the top left slot and enables synchronization sharing between Flexi BTS and other systems. FYGD obtains +15V from the Sync In (HDMI) port of the System Module.

g

Note that Flexi GPS Box (FYGD) is IP20-rated and for indoor site use only.

RF Cable

Passive GPS Antenna

Splitter

RF Cable

To other system GNSS

GNSS Ant

Sync Out

RJ45

RJ45

CMCC In

CMCC Out

CMCC

Status

PWR On/Off

HDMI Cable

Figure 46

82

GPS Box deployment

Id:0900d805809d1e96 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

24.2

Flexi GPS Box (FYGD) description

Flexi GPS Box (FYGD) dimensions and weight Property

Value

Height

30 mm (1.18 in.)

Depth

300.5 mm (11.83 in.)

Width

182.5 mm (7.18 in.)

Weight

1.5 kg (3.31 lbs)

Table 40

24.3

Flexi GPS Box (FYGD) dimensions

Flexi GPS Box (FYGD) interfaces The front panel is shown in Figure 47 Flexi GPS Box (FYGD) front panel.

HDMI

RJ45

RJ45

Sync Out

CMCC In

CMCC Out

SMA Female

GNSS Ant Figure 47

GNSS

CMCC Status

Flexi GPS Box (FYGD) front panel Property

Value

GNSS Antenna Port

SMA female

Sync Out

HDMI

CMCC 1PPS+TOD Input Port (CMCC In)/CMCC 1PPS+TOD Output Port (CMCC Out)

RJ45

Timing Resource Switch (GNSS/CMCC)

Either GPS or CMCC 1PPS+TOD can be selected as primary timing resource by the switch. The factory default setting is GNSS.

Power Switch (On/Off)

For turning o/off the power supply

Table 41

PWR On/Off

Flexi GPS Box (FYGD) interfaces

FYGD delivery includes one 0.6 m (2 ft.) HDMI Sync cable.

DN09142347

Id:0900d805809d1e96 Confidential

83

Flexi GPS Box (FYGD) description

24.4

Flexi GPS Box (FYGD) LED indications • •

84

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

One red LED is used to indicate the power supply. One green LED: – Solid on to indicate that the primary timing resource is being used. – Slowly blinking with 1s on and 1s off to indicate that the secondary timing resource is being used. – When the primary timing resource is CMCC, off to indicate both timing resources are failed.

Id:0900d805809d1e96 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Cabinet for Indoor (FCIA) description

25 Flexi Cabinet for Indoor (FCIA) description 25.1

Flexi Cabinet for Indoor (FCIA) construction This section describes the following hardware: •

Flexi Cabinet for Indoor (FCIA) 470152A

Figure 48

Flexi Cabinet for Indoor (FCIA)

Flexi Cabinet for Indoor (FCIA) provides 19-inch wide free space for installing Flexi modules. It has a cabinet core made of an aluminium chassis enclosed with aluminium sides and door. The FCIA cabinet does not carry any electrical functionality; there are no traditional backplanes or electronics. The cable entries are located at the top of the cabinet. External cables are connected directly to the Flexi modules inside the cabinet. The following optional modules can be mounted to the FCIA cabinet: • • •

DN09142347

Flexi Power Rectifier (FPRx) Flexi System External Alarm Module (FSEB) Flexi System External OVP (FSEC/FSES)

Id:0900d805809c3642 Confidential

85

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

25.2

Flexi Cabinet for Indoor (FCIA) optional items This section describes the optional items of Flexi Cabinet for Indoor (FCIA). Flexi Battery Mounting Kit for FCIA (FMBB) Flexi Battery Mounting Kit (FMBB) 471459A is needed when using batteries in FCIA. The mounting kit is installed at the bottom of the cabinet. Flexi Power Rectifier (FPRx) Flexi Rectifier Module (FPRA) CS7000000 is a modular 6kW output power AC rectifier package made up of three individual 2kW AC/DC power modules operating in a parallel mode configuration. The FPRA outputs a positive earthed –54VDC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. It supports Flexi Multiradio BTS configurations in indoor and outdoor cabinets, and stack, pole and wall configurations. Flexi System External Alarm (FSEB) Flexi System External Alarm (FSEB) 471424A is installed on the cabinet roof and used for extending the Flexi BTS alarm connector up to 24 alarms. For more information on the FSEB, see Flexi System External Alarm (FSEB) description. Flexi System External OVP (FSEC/FSES) Flexi System External OVP (FSEC/FSES) 471397A/472285A is an IP-protected enclosure for overvoltage protection and power terminals. The FSEC/FSES is installed on the cabinet roof. For more information on the OVP enclosures, see Flexi System External OVP (FSEC) description or Flexi System External OVP (FSES) description.

86

Id:0900d805809d8eaf Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

25.3

Flexi Cabinet for Indoor (FCIA) dimensions and weight See Table 42 Dimensions and weight of Flexi Cabinet for Indoor (FCIA) for the dimensions and weight of the Flexi Cabinet for Indoor (FCIA). Property

Value

Height

1793 mm/40.3 U (70.59 in.)

Width

597 mm (23.50 in.)

Depth

521 mm (20.51 in.)

Weight

59.0 kg

(empty cabinet)

(130 lb)

Free space for modules

36 U

Table 42

DN09142347

Dimensions and weight of Flexi Cabinet for Indoor (FCIA)

Id:0900d805809a42e1 Confidential

87

Flexi Cabinet for Outdoor (FCOA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

26 Flexi Cabinet for Outdoor (FCOA) description 26.1

Flexi Cabinet for Outdoor (FCOA) construction This section describes the following hardware: •

Flexi Cabinet for Outdoor (FCOA) 470142A

Figure 49

Flexi Cabinet for Outdoor (FCOA)

Flexi Cabinet for Outdoor (FCOA) provides 19-inch wide free space for installing Flexi modules. It has a cabinet core made of an aluminium chassis enclosed with aluminium sides and door. The cabinet door can be locked with a triangle door-open key. The cabinet can also be fitted with an optional security lock for additional protection. The FCOA itself does not have any electrical functionality and therefore, it does not increase Flexi BTS site power consumption. The cabinet has the following functions: • • •

88

it provides the base station and cables protection against external damage and foreign objects it provides earthquake protection for an installation of more than nine modules it houses the Flexi Cabinet Site Support Module (FCSA) that provides long-term battery back-up and a 4U-high IP55-protected space for Line Terminal Equipment, or Flexi Cabinet Outdoor Small (FCOS) that provides an 8U-high IP55-protected space.

Id:0900d805809c9731 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

•

DN09142347

Flexi Cabinet for Outdoor (FCOA) description

together with Flexi Cabinet Air Filter (FCFA), it protects the BTS in extremely dirty conditions

Id:0900d805809c9731 Confidential

89

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

26.2

Flexi Cabinet for Outdoor (FCOA) optional items This section describes the optional items of Flexi Cabinet for Outdoor (FCOA). Flexi Cabinet Air Filter (FCFA) The optional air filter (FCFA) 470146A can be added in case of extremely dirty environment (for fresh air cooled modules). The optional air filter provides cover for extremely dirty conditions by over-pressurizing the cabinet. The FCFA delivery includes the air filter and a wind plate. The air filter is installed in the back of the cabinet, replacing the original back wall. It consists of a filter element, eight axial fans, a control logic, and back wall mechanics. The pressure sensor is integrated with the control box. The wind plate is installed in the cabinet door. The control of the FCFA fans is based on a pressure sensor. The pressure sensor measures pressure inside the cabinet and this information is then used for controlling the fan speed. The air filter is presented in Figure 50 Flexi Cabinet Air Filter (FCFA).

Figure 50

Flexi Cabinet Air Filter (FCFA)

Flexi Cabinet Site Support Module (FCSA) The optional site support module (FCSA) 470145A can be used with the outdoor cabinet to provide long-term battery back-up time for the Flexi BTS and a space for installing line terminal equipment units. The FCSA provides IP55 protected installation space for the power distribution unit (PDU), IBBU AC interface box, rectifier units, line terminal equipment, control card, heat exchanger, and fans.

90

Id:0900d805809c9733 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

g

Flexi Cabinet Site Support Module (FCSA) does not include a heater. Therefore, the lowest temperature inside the FSCA module might be the ambient temperature. The highest allowed temperature for the FCSA module is +50°C (+122°F). The allowed temperature of the units has to be checked before installing them into the FCSA module. The maximum inside temperature of the FCSA module might be approximately 10 to 20 degrees of Celsius higher than the ambient temperature. This is caused by the inside heat dissipation. There is a separate option for battery installation in the site support module. Batteries are fixed and cabled using Flexi Mounting Kit for Batteries (FMBA). The kit contains battery cables, a cable from IBBU to the battery cables for safe installation, rubber spacers, and front fixing parts to the batteries. The site support is presented in Figure 51 Flexi Cabinet Site Support Module (FCSA).

Heat Exchanger

Control card

Batteries LTE Space FMBA Figure 51

Flexi Cabinet Site Support Module (FCSA)

Flexi Cabinet Outdoor Small (FCOS) Flexi Cabinet Outdoor Small (FCOS) 472395A is designed to house 19-inch multiplexers and microwave radio indoor units. It provides an IP-protected space of 8U for installing IP20-rated units.

DN09142347

Id:0900d805809c9733 Confidential

91

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Cabinet Fire Detector (FCDA) Flexi Cabinet Fire Detector (FCDA) 470144A is installed on the cabinet roof, and the cables are routed to the Flexi System External Alarm (FSEB). The fire detector measures heat by means of a thermistor. The temperature is measured every two seconds. A microprocessor stores the result and compares with pre-defined value to determine whether a maximum temperature is reached. The fire detector responds only when a fixed temperature of +80°C (+176°F) is reached. Figure 52 Flexi Cabinet Fire Detector (FCDA) presents the fire detector.

DN70150541

Figure 52

Flexi Cabinet Fire Detector (FCDA)

Flexi Power Rectifier (FPRx) Flexi Rectifier Module (FPRA) CS7000000 is a modular 6kW output power AC rectifier package made up of three individual 2kW AC/DC power modules operating in a parallel mode configuration. The FPRA outputs a positive earthed –54VDC (V48N) as a respective BTS operational supply voltage rail and for site battery charging. It supports Flexi Multiradio BTS configurations in indoor and outdoor cabinets, and stack, pole and wall configurations. Flexi System External Alarm (FSEB) Flexi System External Alarm (FSEB) 471424A is installed on the cabinet roof and used for extending the Flexi BTS alarm connector up to 24 alarms. For more information on the FSEB, see Flexi System External Alarm (FSEB) description. Flexi System External OVP (FSEC/FSES) Flexi System External OVP (FSEC/FSES) 471397A/472285A is an IP-protected enclosure for overvoltage protection and power terminals. The FSEC/FSES is installed on the cabinet roof. For more information on the OVP enclosures, see Flexi System External OVP (FSEC) description or Flexi System External OVP (FSES) description.

92

Id:0900d805809c9733 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

26.3

Flexi Cabinet for Outdoor (FCOA) dimensions and weight Table 43 Dimensions and weight of Flexi Cabinet for Outdoor (FCOA) shows the dimensions and weight of Flexi Cabinet for Outdoor (FCOA). Property

Value

Height

1550 mm (61 in.)

Width

770 mm (30.3 in.)

Depth

770 mm (30.3 in.)

Depth with air filter

930 mm (36.6 in.)

Depth with air filter and wind plate

1020 mm (40.2 in.)

Weight

63.2 kg

(empty cabinet)

(139.3 lb)

Weight

97.2 kg

(with air filter and wind plate)

(214.3 lb)

Total weight

358 kg

(fully equipped with batteries)

(789 lb)

Free space for modules

40 U (30 U horizontally + 5 U + 5 U vertically

Free space for modules

21 U

(site support and batteries installed)

(16 U horizontally + 5 U vertically)

Table 43

DN09142347

Dimensions and weight of Flexi Cabinet for Outdoor (FCOA)

Id:0900d805809d5428 Confidential

93

Flexi Mounting Shield (FMSA and FMSB) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

27 Flexi Mounting Shield (FMSA and FMSB) description 27.1

Flexi Mounting Shield (FMSA and FMSB) operation and construction This section describes the following hardware: • •

Flexi Mounting Shield (FMSA) 471614A Flexi Mounting Shield (FMSB) 471650A

DN70324735

Figure 53

94

Isometric view of the FMSA

Id:0900d805809bf76a Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Mounting Shield (FMSA and FMSB) description

DN70324723

Figure 54

Isometric view of the FMSB

Flexi Mounting Shield (FMSA/FMSB) is an outdoor cabinet for a stacked Flexi BTS. Used instead of the plastic front and rear covers, it provides protection against solar load, large insects and slight vandalism. Flexi Mounting Kit for Floor, Wall and Pole (FMFA) is required inside both cabinets for Flexi module installations. The FMSA provides installation space for up to any two Flexi 3U modules and the plinth (6U in total). It is installed on a pole or wall. The FMSB provides space for up to any six Flexi 3U modules and the plinth (18U in total). It is installed on the floor. Modules are installed in casings without front and back covers and cable entries. The cabinet door is right-handed (the handedness cannot be changed). For installation instructions, see sections Installing Flexi Mounting Shield 6U (FMSA) and Installing Flexi Mounting Shield 18U (FMSB) in the Installing Flexi Multiradio BTS LTE Modules in Cabinets document.

DN09142347

Id:0900d805809bf76a Confidential

95

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

27.2

Flexi Mounting Shield (FMSA and FMSB) dimensions and weights See Table 44 Flexi Mounting Shield 6U (FMSA) dimensions and weight and Table 45 Flexi Mounting Shield 18U (FMSB) dimensions and weight for the dimensions and weight of the Flexi Mounting Shields (FMSA/FMSB). Property

Value

Height

605 mm (23.8 in.)

Width

400 mm (15.7 in.)

Depth

620 mm (24.4 in.)

Weight (empty)

12 kg (26.5 lb)

Free space for modules

Table 44

6U

Flexi Mounting Shield 6U (FMSA) dimensions and weight

Property

Value

Height

930 mm (36.6 in.)

Width

605 mm (23.8 in.)

Depth

620 mm (24.4 in.)

Weight (empty)

21 kg (46.3 lb)

Free space for modules

Table 45

96

18U

Flexi Mounting Shield 18U (FMSB) dimensions and weight

Id:0900d805809bf786 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Cabinet Outdoor Small (FCOS) description

28 Flexi Cabinet Outdoor Small (FCOS) description This section describes the following hardware: • •

Flexi Cabinet Outdoor Small (FCOS) 472395A Optional items: • Flexi Cabinet Wall Kit (FCWA) 472396A • Flexi Cabinet Pole Kit (FCPA) 472397A • Flexi Cabinet Cabinet Assembly Kit (FCCA) 472398A

Figure 55

28.1

Flexi Cabinet Outdoor Small (FCOS) installed on the floor

Flexi Cabinet Outdoor Small (FCOS) construction Flexi Cabinet Outdoor Small (FCOS) is an outdoor cabinet designed to house 19-inch multiplexers and microwave radio indoor units. It provides a space of 8U for installing IP20 units. The ingress protection rating of FCOS is IP55. Maximum allowed heat load is 600 W. Installation options: • •

DN09142347

stand-alone on the floor stackable with Flexi modules (on top of a Flexi casing or plinth)

Id:0900d805809c3646 Confidential

97

Flexi Cabinet Outdoor Small (FCOS) description

• • •

g 28.2

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

pole/wall installations – same fixing points as for Flexi modules 19-inch rack installation inside Flexi Cabinet for Outdoor (FCOA) FCOS has a factory-installed dust filter that can be replaced without turning the power off. Flexi Cabinet Outdoor Small (FCOS) is recommended instead of Flexi Cabinet Site Support Module (FCSA).

Flexi Cabinet Outdoor Small (FCOS) optional items The following optional items are available for Flexi Cabinet Outdoor Small (FCOS): • • •

28.3

Flexi Cabinet Wall Kit (FCWA), which consists of wall mounting brackets and screws needed for installing FCOS on a wall. Flexi Cabinet Pole Kit (FCPA), which is used together with a pole mounting kit (FPKA, FPKC or VMPB). Flexi Cabinet Cabinet Assembly Kit (FCCA), which consists of fixing rails and screws needed for installing FCOS inside Flexi Cabinet for Outdoor (FCOA).

Flexi Cabinet Outdoor Small (FCOS) dimensions and weight Property Height

Value 625 mm (24.6 in.)

Height with feet

805 mm (31.7 in.)

Width

451 mm (17.7 in.)

Depth

510 mm (20.1 in.)

Weight

24.3kg (53.5 lb)

Table 46

Flexi Cabinet Outdoor Small (FCOS) dimensions and weight

For installation instructions, see Installing Flexi Multiradio BTS LTE Modules in Cabinets.

98

Id:0900d805809c3646 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Mounting Kit Vertical for 2G (FMUA) description

29 Flexi Mounting Kit Vertical for 2G (FMUA) description 29.1

Flexi Mounting Kit Vertical for 2G (FMUA) operation This section describes the following hardware: •

Flexi Mounting Kit Vertical for 2G (FMUA) 470323A

2G

System Module

1 U free space

RF Module

Figure 56

Flexi Mounting Kit Vertical for 2G (FMUA) with Flexi Multiradio BTS installed

With Flexi Mounting Kit Vertical for 2G (FMUA), Flexi Multiradio modules can be installed on existing GSM/EDGE UltraSite sites. The mounting kit can be used with the following indoor and outdoor GSM/EDGE UltraSite cabinets: • • •

UltraSite EDGE BTS (CRMA) UltraSite Indoor Cabinet (IDCA) v. 101 UltraSite Outdoor Cabinet (ODCA) v. 101

Before the mounting kit can be installed, the following parts are removed from the lower half of the GSM/EDGE UltraSite cabinet: • •

DN09142347

3 x fans RFU back plane

Id:0900d805809d20b3 Confidential

99

Flexi Mounting Kit Vertical for 2G (FMUA) description

•

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

WBC fan box

The mounting kit consists of one dual rack in which one System Module and one RF Module are installed, one single rack for the second RF Module installation, and cables. There is a remaining space of 1U in the single rack when the RF Module is installed. Note that FMUA does not support FSMF/G/L installations. For installation instructions, see section Overview of installing modules in cabinet with Flexi Mounting Kit Vertical for 2G in the Installing Flexi Multiradio BTS LTE Modules in Cabinets document.

100

Id:0900d805809d20b3 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

29.2

Flexi Mounting Kit Vertical for 2G (FMUA) construction The mounting kit dual rack and single racks are made of aluminium and include mounting for fans and air ducts. See Figure 57 FMUA parts (dual and single racks) for an illustration of the racks.

Dual rack FRONT

BACK

Single rack FRONT

BACK

DN7082037

Figure 57

DN09142347

FMUA parts (dual and single racks)

Id:0900d8058099ae87 Confidential

101

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

29.3

Technical properties of Flexi Mounting Kit Vertical for 2G (FMUA) Table 47 FMUA dimensions and weights illustrates the dimensions and weights of the two racks of the mounting kit. Property

Dual rack

Single rack

Height

694 mm

585 mm

(27.3 in.)

(23 in.)

302 mm

196 mm

(11.9 in.)

(7.7 in.)

395 mm

400 mm

(15.6 in.)

(15.8 in.)

6.2 kg

4.6 kg

(13.7 lbs)

(10.2 lbs)

0.7dB

0.7dB

Width Depth

Weight The loss of RF cables

Table 47

102

FMUA dimensions and weights

Id:0900d8058099ae95 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Mounting Kit Horizontal for 2G (FMUB) description

30 Flexi Mounting Kit Horizontal for 2G (FMUB) description 30.1

Flexi Mounting Kit Horizontal for 2G (FMUB) operation and construction This section describes the following hardware: •

Flexi Mounting Kit Horizontal for 2G (FMUB) 471280A

DN70231874

Figure 58

Flexi Mounting Kit Horizontal for 2G (FMUB)

With Flexi Mounting Kit Horizontal for 2G (FMUB), Flexi Multiradio modules can be installed on existing GSM/EDGE UltraSite sites. The mounting kit can be used with the following indoor and outdoor GSM/EDGE UltraSite cabinets: • • •

UltraSite Indoor Cabinet (IDCA) v. 202 or newer UltraSite Outdoor Cabinet (ODCA) v. 202 or newer UltraSite EDGE Outdoor Cabinet (ODCF)

The mounting kit consists of a rack in which, for example, one Multiradio System Module, up to three Multiradio RF Modules and one FPMA or FPDA are installed, and cables. The space requirement for 5 x 3U modules is 15U. For installation instructions, see section Installing modules in cabinet with Flexi Mounting Kit Horizontal for 2G in the Installing Flexi Multiradio BTS LTE Modules in Cabinets document.

DN09142347

Id:0900d805809d20c1 Confidential

103

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

30.2

Technical properties of Flexi Mounting Kit Horizontal for 2G (FMUB) Table 48 FMUB dimensions and weight illustrates the dimensions and weight of the FMUB. Property

FMUB

Height

732 mm (28.8 in.)

Width

525 mm (20.7 in.)

Depth

393 mm (15.5 in.)

Weight of the side wall

1.73kg (3.8 lbs)

Weight

20 kg

(cables excluded)

(44 lbs)

The loss of RF cables

0.7dB

Table 48

104

FMUB dimensions and weight

Id:0900d805809d5498 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Talk Conversion Kit (EMIB) description

31 Talk Conversion Kit (EMIB) description This section describes the following hardware: •

Talk Conversion Kit (EMIB) 471953A Screws and washers (4pcs) 2) Upper rod lock support (2pcs) 1) Top IP Cover 1) Air guide plate 1)

Top support plate 1)

Citytalk cabinet and roof 2)

Top support C-plate 1)

Roof mounting plate 2)

Back wall

Rack side plate Left and right assembly 1) Taps, clips, pins retaining rings and M6 screws (4 sets) 2)

Support rail (14 pcs) 1)

Rack plinth 1) Standoff proximity bracket 1)

Lock cylinder 2) Lock cover 1)

Door proximity bracket 1) Door 1)

Figure 59

Hinges (2 pcs) and screws (8pcs) 2)

1) Part of Talk Conversion kit 2) Existing items of Citytalk cabinet

Parts needed for installing Flexi BTS modules in Citytalk cabinet with Talk Conversion Kit (EMIB)

Flexi Multiradio BTS modules can be installed into the CityTalk cabinet by using the Talk Conversion Kit (EMIB). The inner parts of the CityTalk cabinet are removed before the Flexi Multiradio modules are installed and certain parts of the CityTalk cabinet are replaced with new parts belonging to the EMIB kit. The CityTalk cabinet retains its outline dimensions and the mechanical shape when modified with EMIB. The Flexi Multiradio BTS within the modified cabinet fulfils the any requirements imposed on the product. For installation instructions, see the Installing Flexi Multiradio BTS LTE Modules in Cabinets document.

DN09142347

Id:0900d805809c2763 Confidential

105

UltraSite Outdoor Side Kit (OSKA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

32 UltraSite Outdoor Side Kit (OSKA) description This section describes the following hardware: •

UltraSite Outdoor Side Kit (OSKA) 471669A

A

A Wall bracket M6 Torque screw, star and flat washers M6 Torque screw, star and flat washers A

A Wall bracket M6 Torque screw, star and flat washers M6 Torque screw, star and flat washers

Figure 60

UltraSite Outdoor Side Kit (OSKA)

The OSKA UltraSite Outdoor Side Kit is used to enhance current UltraSite BTSs by adding FlexiBTS modules to it without the need of adding an extra cabinet.

106

Id:0900d805809d20c7 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

UltraSite Outdoor Side Kit (OSKA) description

The side kit allows both WCDMA and GSM/EDGE Flexi modules to be connected to it, with each module being housed within a Flexi housing. The Flexi Rectifier Module (FPRA) can also be mounted directly to the side kit without the need of a Flexi Housing. The side kit can be fixed to either the left-hand side, right-hand side, or the rear of an Ultrasite Outdoor cabinet. A maximum of two modules can be stacked on top of each other to three different fixing points in one plate. This results to a total installation of six Flexi modules. Note that only two faces of an Ultrasite Outdoor cabinet can be used at any one time, which are left-hand side and rear or right-hand side and rear. If two faces are used then it yields to a maximum of 12 Flexi modules’ installation. Both left-hand side and right-hand-side cannot be used at the same time. The maximum weight of modules in each face is 130 kg (286.6 lbs). If both side and rear faces are used, then the maximum weight is 260 kg (573.2 lbs). For details, see the figure below:

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

F L E X I

REAR

REAR

Figure 61

Side kits fixed to the cabinet

As an alternative to Flexi modules installation it is possible to install Flexi Mounting Shield onto the OSKA plate. A maximum of two Flexi Mounting Shields on one face (130 kg) can be used. If two faces (side and rear) are used, it is possible to install four Mounting Shields (260 kg). For installation instructions, see Installing UltraSite Outdoor Side Kit (OSKA).

DN09142347

Id:0900d805809d20c7 Confidential

107

UltraSite IDC_ Roof Kit (IRSA) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

33 UltraSite IDC_ Roof Kit (IRSA) description This section describes the following hardware: •

UltraSite IDC_ Roof Kit (IRSA) 471670A Mask upper

Torx screw M5x10 Ferritic stainless steel Connection pin

Hex nut M8 A4 4 pcs Rivet 4.0x7.6

Washer M8

ESD stud Adapter plate Mounting rail 2 pcs

M5x10 screw 2 pcs

M8 washer M8 screw

Support rail 4 pcs

Washer 2 pcs

Plastic washer 2 pcs Mask side 2 pcs

Figure 62

Mask front

Torx screw M5x10 Ferritic stainless steel

UltraSite IDC_ Roof Kit (IRSA)

The IRSA UltraSite IDC_ Roof Kit is used to install the Flexi Rectifier module (FPRA), or any other Flexi unit, on the roof of an UltraSite Indoor cabinet. For improved access to the Antenna Connections on the IDC_ Antenna Box, the adapter plate of the IRSA Ultrasite IDC_ Roof Kit can be fitted in a forward position. The kit can also be adapted so that it can be used for mounting units on the side of the IDC_ cabinet. The FPRA is configured as part of the respective BTS and forms a fully integrated solution for sites requiring battery backed-up facility. For this application, either the FPRA or Flexi modules can be installed. Three Flexi modules can be installed into an IRSA roof kit on the cabinet roof. The maximum weight of modules on the roof is 53 kg (116.8 lbs). For installation instructions, see Installing UltraSite IDC_ Roof Kit (IRSA).

Figure 63

108

Mounting in forward position

Id:0900d805809d20d1 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi TRS External Filter for FHCA (FFCB) description

34 Flexi TRS External Filter for FHCA (FFCB) description This section describes the following hardware: •

Flexi TRS External Filter for FHCA (FFCB) 472556A

Figure 64

Flexi TRS External Filter for FHCA (FFCB)

Flexi TRS External Filter for FHCA (FFCB) is an external filter that is used together with Flexi RRH 2TX 850 (FHCA). The FFCB allows to fulfill demanding co-siting requirements on Korean radio systems.

34.1

Flexi TRS External Filter for FHCA (FFCB) operation The FFCB can be installed: • •

DN09142347

on a wall on a pole

Id:0900d805809d20d3 Confidential

109

Flexi TRS External Filter for FHCA (FFCB) description

Figure 65

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi TRS External Filter for FHCA (FFCB) mounted on a pole

The FFCB provides the following features: • • • •

34.2

Four 7/16 antenna connectors (one pair towards the BTS and one towards RRH) Two output ports (SMA, female) for power monitoring Operating temperature range: -40°C to +55°C (-40ºF to 131ºF) Ingress protection: IP65

Flexi TRS External Filter for FHCA (FFCB) interfaces See Table 49 Flexi TRS External Filter for FHCA (FFCB) interfaces for FFCB interfaces.

110

Id:0900d805809d20d3 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi TRS External Filter for FHCA (FFCB) description

Port

Connector type

Purpose

Antenna connector (2 pcs)

7/16 type, female

RF signal interface to antenna(s)

BTS connector (2 pcs)

7/16 type, female

RF signal interface to the BTS

Ptx (2 (pcs)

SMA, female

Power monitoring

straight with metal cap and chain Table 49

34.3

Flexi TRS External Filter for FHCA (FFCB) interfaces

Flexi TRS External Filter for FHCA (FFCB) dimensions and weight The dimensions and weights of the FFCB are presented in Table 50 Flexi TRS External Filter for FHCA (FFCB) dimensions and weight. Property

FFCB

Width

260 mm (10.23 in.)

Height

482 mm (19 in.)

Depth

121 mm (4.76 in.)

Weight

less than 10 kg (22 lb)

Table 50

DN09142347

Flexi TRS External Filter for FHCA (FFCB) dimensions and weight

Id:0900d805809d20d3 Confidential

111

Flexi TRS External Filter for FXCA (FFCC) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

35 Flexi TRS External Filter for FXCA (FFCC) description This section describes the following hardware: •

Flexi TRS External Filter for FXCA (FFCC) 472556A

Figure 66

Flexi TRS External Filter for FXCA (FFCC)

Flexi TRS External Filter for FXCA (FFCC) is an external filter that is used together with Flexi 3-sector RF Module 850 60W (FXCA). The FFCC allows to fulfill demanding cositing requirements on Korean radio systems.

35.1

Flexi TRS External Filter for FXCA (FFCC) operation The FFCC can be installed: • •

On a pole or wall. Into a dedicated external filter casing.

The FFCC provides the following features: • Four 7/16 antenna connectors (one pair towards the BTS and one towards RRH) • Wanted frequency band: – RX: 839 - 849 MHz – TX: 884 - 894 MHz • Two output ports (SMA, female) for power monitoring • Operating temperature range: -40°C to +55°C (-40°F to 131°F) • Ingress protection: IP65

35.2

Flexi TRS External Filter for FXCA (FFCC) interfaces See Table 51 Flexi TRS External Filter for FXCA (FFCC) interfaces and Figure 67 Bottom view of the FFCC for FFCC interfaces.

112

Id:0900d805809d20f3 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi TRS External Filter for FXCA (FFCC) description

Port

Connector type

Purpose

Antenna connector (2 pcs)

7/16 type, female

RF signal interface to antenna(s)

BTS connector (2 pcs)

7/16 type, female

RF signal interface to the BTS

Ptx (2 (pcs)

SMA, female

Power monitoring

straight with metal cap and chain

35.3

Table 51

Flexi TRS External Filter for FXCA (FFCC) interfaces

Figure 67

Bottom view of the FFCC

Flexi TRS External Filter for FXCA (FFCC) dimensions and weight The dimensions and weights of the FFCC are presented in Table 52 Flexi TRS External Filter for FXCA (FFCC) dimensions and weight. Property

FFCC

Width

145 mm (5.7 in.)

Height

120 mm (4.7 in.)

Depth

324 mm (12.7 in.)

Weight

less than 9 kg (19.8 lb)

Table 52

DN09142347

Flexi TRS External Filter for FXCA (FFCC) dimensions and weight

Id:0900d805809d20f3 Confidential

113

Repeater Interface Module (FHCC) description

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

36 Repeater Interface Module (FHCC) description This section describes the following hardware: •

Repeater Interface Module (FHCC) 472662A

Figure 68

Repeater Interface Module (FHCC)

Repeater Interface Module (FHCC) is a special purpose Remote Radio Head, which interconnects the System Module and operators’ repeater system.

36.1

Repeater Interface Module (FHCC) operation and main blocks The FHCC includes six full pipes of transmitters and receivers which can be connected to the operators’ repeater system through analog IF interfaces. Transmitters and receivers consist of digital transceiver sections and analog IF sections. RF sections are not included in the RIM since the RF frequency converter and power amplifier are accommodated by the repeater system. The FHCC supports two modes of working: • •

36.2

dedicated mode, that is, the FHCC is directly connected to the operators’ repeater system only. coupling sector mode. In this mode FHCC is connected to both, operators’ repeater system and RF Modules. The repeater system shares the same I/Q data with RF Modules in downlink. The uplink I/Q data are diversity summed, path by path in the RIM.

Repeater Interface Module (FHCC) interfaces One RIM supports up to three sectors. Each sector has two TX and two RX supporting 2x2 MIMO. RIM is connected to the System Module through an optical fiber link with OBSAI RP3-01 interfaces. It has additional OBSAI RP3-01 optical interfaces to provide interconnections with RF Modules.

114

Id:0900d805809d20fd Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Repeater Interface Module (FHCC) description

See Table 53 Repeater Interface Module (FHCC) interfaces and Figure 69 Front panel view of the FHCC for FHCC interfaces. Name

Initial

Power Supply1)

Number of interfaces

Level

Connected

I/O

DC IN

1

-48V, 48RTN

System Module or Power Supply Unit

I

Grounding

GND

1

GND

Grounding bar

O

Operational State Visual Indication (Fan alarm and Module Status)

LED

2x2

LVTTL

LED for the two TRX sub assemblies

O

(fuse protected)

Unit/Fan

Optical

interface2)

SM1-4

2x2

Optical

System Module

I/O

Optical

interface3)

RU1-4

2x2

Optical

RF Module

I/O

LMT

1x2

Ethernet

Local Maintenance

I/O

RS232

R232

1x2

RS232

Front Panel

I/O

Transmitter

TX1..3/M

3x2

Analog IF

Delay Equalizer

O

Mon

3x2

Analog IF

Test instruments on site

O

Test

connector4)

Transmitter Monitor

TX1..3/M Receiver

RX1..3/M

3x2

Analog IF

Delay Equalizer

I

Receiver Monitor

Mon(10dB)

3x2

Analog IF

Test instruments on site

O

1x2

Analog IF

Test instruments on site or Delay Equalizer

O

RX1..3/M 10MHz Reference Clock

10MHz REF/D

Table 53 1) 2) 3) 4)

Repeater Interface Module (FHCC) interfaces

Power consumption is around 180W. Optical interface connecting to System Module. LC-APC type 2-core multiple-mode SFP TRX module. Optical interface connecting to RF Module. LC-APC type 1-core single-mode SFP TRX module. Access through an adapter card, JTAG port, EAC port and MCU boot debug UART port can be led out of RIM box.

g

3x2 in the number of interfaces column means two TRX board, each board has three interfaces.

Figure 69

DN09142347

Front panel view of the FHCC

Id:0900d805809d20fd Confidential

115

Repeater Interface Module (FHCC) description

36.3

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Repeater Interface Module (FHCC) dimensions and weight The FHCC assembly contains two identical boards. RIM is 433 mm (17.05 in.) deep together including cooling fans. It can be installed into any 19-inch standard rack and to third-party standard cabinets. The ingress protection level of the indoor module is IP20. The cooling system has three individual 60 mm (2.36 in.) fans which are mounted on the backside of the chassis. The hot air is sucked out from the back of the module. The operating ambient temperature of the unit is in the range of 0ºC to +65ºC (32ºF to 149ºF). The dimensions and weights of the FHCC are presented in Table 54 Repeater Interface Module (FHCC) dimensions and weight. Property

FHCC

Width

433 mm (17.05 in.)

Height

87.2 mm (3.43 in.)

Depth

434 mm (17.09 in.)

Weight

14.8 kg (32.6 ls)

Table 54

36.4

Repeater Interface Module (FHCC) dimensions and weight

Repeater Interface Module (FHCC) power requirements The rectifier which provides power to RIM should have minimum 180W output capability, and the input to RIM should be within -48V +/-20% range.

36.5

Repeater Interface Module (FHCC) LED indications The FHCC module status indicator and fan failure indicator are tricolor LEDs. The main LED indications of the FHCC are listed and explained in Table 55 Repeater Interface Module (FHCC) LED indications. LED mode

Priority

Explanation

None

0 (highest)

SM O&M control

Red, stable for less than 5 sec.

1

Resetting/switched on

Yellow, stable

2

Initialization/disconnected (no optical link)

Red, periodic stable (500ms)

3

Module highlighting (through RP1 control messages)

Yellow, stable

4

Block (through RP1 control messages)

Red, stable

5

Faulty (RRH critical alarm, out of order)

Yellow, stable (500ms) Green, stable (500ms)

Table 55

116

Repeater Interface Module (FHCC) LED indications

Id:0900d805809d20fd Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Repeater Interface Module (FHCC) description

LED mode

Priority

Explanation

Red and green periodic

6

ALD faulty (ALD critical alarm, out of order)

Red, blinking

7

Degraded (RRH major alarm)

Red and green periodic

8

ALD degraded (ALD major alarm)

Yellow, blinking

9

SW downloading (startup, not enabled)

Yellow, blinking

10

Configuration (optical connection ok, not enabled)

Green, blinking

11

SW downloading (normal operation, enabled)

Green, stable

12

Working (module configured and enabled)

Table 55

Repeater Interface Module (FHCC) LED indications (Cont.)

Fan status LED indications: • •

DN09142347

Stable RED - one or more fans faulty or degraded Stable GREEN - all fans working

Id:0900d805809d20fd Confidential

117

Flexi Multiradio BTS and Flexi Multiradio 10 BTS cables and SFPs

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37 Flexi Multiradio BTS and Flexi Multiradio 10 BTS cables and SFPs 37.1

Transmission cables Outdoor (OD) cables for transmission sub-modules Sales item 472427A

Table 56

Name FTCY OD Cable RJ48C Cat7 15 m

Length [m] 15 m

For FTIF

Notes RJ48C open end

Flexi Multiradio 10 BTS transmission cables

Outdoor (OD) cables for transmission sub-modules Sales item

Length [m]

For

Notes

470312A

FTCA OD 5m Cable RJ48C - TQM/0 120 ohm 5 m

FTPB, FTIA

RJ48C - TQ, 1 x E1

470309A

FTCB OD Cable RJ48C 120 ohm 15 m

15 m

FTPB, FTIA

RJ48C open end, 1 x E1

471713A

FTCV OD Cable RJ48C 120 ohm 30 m

30 m

FTPB, FTIA

RJ48C open end, 1 x E1

471714A

FTCX OD Cable RJ48C 120 ohm 50 m

50 m

FTPB, FTIA

RJ48C open end, 1 x E1

470313A

FTCD OD Cable SMBF/0 75 ohm 5m

5m

FTEB, FTJA 2 x SMB BT43, 1 x E1 coax

470310A

FTCE OD Cable SMBF/0 75 ohm 15 m

15 m

FTEB, FTJA 2 x SMB open end, 1 x E1 coax

Table 57

118

Name

Flexi Multiradio BTS transmission cables

Id:0900d805809dbe8d Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Flexi Multiradio BTS and Flexi Multiradio 10 BTS cables and SFPs

Outdoor (OD) cables for transmission sub-modules Sales item

Length [m]

For

Notes

471715A

FTCF OD Cable SMBF/0 75 ohm 30 m

30 m

FTEB, FTJA 2 x SMB open end, 1 x E1 coax

471716A

FTCG OD Cable SMBF/0 75 ohm 50 m

50 m

FTEB, FTJA 2 x SMB open end, 1 x E1 coax

470311A

FTCH OD Cable LC SM 1310 15 m

15 m

FTOA

LC duplex LC duplex single-mode fiber (needed for FOSA SFP units)

471391A

FTCJ OD Cable TNCF7O-TNC M/O 50 ohm 2.5 m

2.5 m

FTFA

TNC male TNC female Flexbus

471408A

FTCR OD Cable RJ45 Cat5e 15 m

15 m

FTIA, FTJA

RJ45 - open end, 1 x Ethernet

471548A

FTCP OD Cable MDR68 100 ohm 30 m

30 m

FTHA

MDR68 MDR68

471717A

FTCS OD Cable RJ45 Cat5e 30 m

30 m

FTIA, FTJA

RJ45 - open end, 1 x Ethernet

471718A

FTCT OD cable RJ45 Cat5e 50 m

50 m

FTIA, FTJA

RJ45 - open end, 1 x Ethernet

471392A

FTCM OD 2.5 m Adapter Cable RJ48C 120 ohm

FMUA and FMUB with FTPB or FTJA

RJ48C male - RJ48C female (IP seal on male side)

471393A

FTCN OD Adapter Cable SMB 75 ohm

FMUA and FMUB with FTEB or FTJA

SMB - SMB bulkhead (IP seal on SMB side)

Table 57

DN09142347

Name

2.5 m

Flexi Multiradio BTS transmission cables (Cont.)

Id:0900d805809dbe8d Confidential

119

Flexi Multiradio BTS and Flexi Multiradio 10 BTS cables and SFPs

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Outdoor (OD) cables for transmission sub-modules Sales item 471394A

Table 57

Name FTCO OD Adapter Cable TNC

Length [m] 2.5 m

For FMUA and FMUB with FTFA

Notes TNC - TNC bulkhead (no IP seal)

Flexi Multiradio BTS transmission cables (Cont.)

Outdoor (OD) cables for transmission units Sales item

Length [m]

For

Notes

470309A

FTCB OD Cable RJ48C 120 ohm 15 m

15 m

Transmission unit ->

RJ48C open end

470310A

FTCE OD Cable SMBF/0 75 ohm 15 m

15 m

Transmission unit ->

2 x SMB open end, 1 x E1 coax

470312A

FTCA OD 5m Cable RJ48C - TQM/0 120 ohm 5 m

Transmission unit ->

RJ48C - TQ, 1 x E1

470313A

FTCD OD Cable SMBF/0-BT43F/0 75 ohm 5m

5m

Transmission unit ->

2 x SMB BT43, 1 x E1 coax

471391A

FTCJ OD Cable TNCF/0-TNCM/0 50 ohm 2.5 m

2.5 m

Transmission unit ->

TNC male TNC female Flexbus

Table 58

120

Name

Flexi Multiradio BTS GSM/EDGE transmission cables

Id:0900d805809dbe8d Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.2

Single-mode fiber cables Single-mode fibers 90°-90° Sales item 472607A

Name

Length [m]

For

Notes

FSOR Flexi 4 m System fiber SM 4 m

SM - RF M/RRH

472867A

FSOP Flexi 10 m SM fiber 9090 10 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, SM

472868A

FSOS Flexi 25 m SM fiber 9090 25 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, SM

Table 59

SM RFM/FODA

LC 90° left IP - LC 90° left IP, SM

Single-mode fibers 90°-90°

Single-mode fibers 0°-90° Sales item

Length [m]

For

Notes

472865A

FSOM Flexi SM fiber 090 2 m

2m

SM - RRH

LC 0° IP LC 90° left IP, SM

472866A

FSON Flexi SM fiber 090 5 m

5m

SM - RRH

LC 0° IP LC 90° left IP, SM

472067A

FSOH Flexi 10 m RRH System fiber SM 10 m

SM - RRH

LC 0° IP LC 90° left IP, SM

472069A

FSOL Flexi 50 m RRH System fiber SM 50 m

SM - RRH

LC 0° IP LC 90° left IP, SM

472070A

FSOO Flexi 110 m RRH System fiber SM 110 m

SM - RRH

LC 0° IP LC 90° left IP, SM

472068A

FSOQ Flexi 200 m RRH System fiber SM 200 m

SM - RRH

LC 0° IP LC 90° left IP, SM

Table 60

DN09142347

Name

Single-mode fibers 0°-90°

Id:0900d805809e4a82 Confidential

121

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.3

Multi-mode fiber cables Multi-mode fibers 90°-90° OM2 Sales item 472894A

Length [m]

For

Notes

FSFL MM fiber 90-90 2 m

2m

471743A

FSFD Flexi System fiber D4m

4m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

471707A

FSFF Flexi System fiber F 10 m

10 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

471708A

FSFG Flexi System fiber G 20 m

20 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

471709A

FSFH Flexi System fiber H 30 m

30 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

471710A

FSFI Flexi System fiber I 40 m

40 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

471395A

FSFB Flexi System fiber B 50 m

50 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM + LC-LC adapter

471711A

FSFK Flexi System fiber K 75 m

75 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

471396A

FSFC Flexi System fiber C 100 m

100 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM + LC-LC adapter

471712A

FSFP Flexi System fiber P 200 m

200 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

Table 61

122

Name

SM - RF M/RRH SM - SM

LC 90° left IP - LC 90° left IP, MM

Multi-mode fibers 90°-90° OM2

Id:0900d805809e4a84 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Multi-mode fibers 90°-90° OM2 Sales item

Name

Length [m]

For

Notes

471851A

FSFO Flexi 2 m System fiber HF 2 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MMhalogenfree + LCLC adapter

471852A

FSFQ Flexi 50 m System fiber HF 50 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MMhalogenfree + LCLC adapter

472131A

FSFE Flexi 2 m System fiber MM 2 m

SM - RF M/RRH

LC 90° left IP - LC 90° left IP, MM

Table 61

Multi-mode fibers 90°-90° OM2 (Cont.)

Multi-mode fibers 90°-90° OM3 Sales item

Name

Length [m]

For

Notes

472844A

FSFM OM3 100 m MM fiber 9090, 100 m

3 Gb or 6 Gb, SM RFM/RRH

LC 90° left IP - LC 90° left IP, MM OM3

472845A

FSFN OM3 200 m MM fiber 9090, 200 m

3 Gb or 6 Gb, SM RFM/RRH

LC 90° left IP - LC 90° left IP, MM OM3

Table 62

Multi-mode fibers 90°-90° OM3

Multi-mode fibers 0°-90° OM2 Sales item

Length [m]

For

Notes

472066A

FSOA Flexi 10 m RRH System fiber MM 10 m

SM - RRH

LC 0° IP LC 90° left IP, MM

472134A

FSOB Flexi 20 m RRH System fiber MM 20 m

SM - RRH

LC 0° IP LC 90° left IP, MM

Table 63

DN09142347

Name

Multi-mode fibers 0°-90° OM2

Id:0900d805809e4a84 Confidential

123

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Multi-mode fibers 0°-90° OM2 Sales item

Length [m]

For

Notes

472135A

FSOC Flexi RRH System fiber MM 30 m

30 m

SM - RRH

LC 0° IP LC 90° left IP, MM

471964A

FYTF Flexi RRH System fiber MM 50 m

50 m

SM - RRH

LC 0° IP LC 90° left IP, MM

472136A

FSOE Flexi RRH System fiber MM 75 m

75 m

SM - RRH

LC 0° IP LC 90° left IP, MM

471965A

FYTG Flexi RRH System fiber MM 100 m

100 m

SM - RRH

LC 0° IP LC 90° left IP, MM

471966A

FYTH Flexi RRH System fiber MM 200 m

200 m

SM - RRH

LC 0° IP LC 90° left IP, MM

Table 63

124

Name

Multi-mode fibers 0°-90° OM2 (Cont.)

Id:0900d805809e4a84 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.4

Small form-factor pluggable transceivers (SFPs) 3 Gb SFPs: • ESMB/C and FSMC/D/E all radio modules • FSMF/G/L radio modules with 3 Gb OBSAI RP3 Sales item

Name

Length [m]

472063A

FOSG Flexi Optical SFP G 850 nm 3 Gb 200 m MM

up to 200 m

472807A

471546A

Table 64

For

Notes

SM - RFM

3 Gb Multimode SFP 850 nm for OBSAI, two needed per connection, LC PC connector

FOSL Flexi up to 2 km Optical SFP L 1310 nm 3 Gb 2 km SM

SM - RFM

3 Gb Single mode SFP 1310 nm for OBSAI, two needed per connection, LC PC connector

FOSA Flexi Optical SFP A 1310 nm 3 Gb 15 km SM

SM - RFM

3 Gb Single mode SFP 1310 nm for OBSAI, two needed per connection, LC PC connector

up to 15 km

3 Gb SFPs

6 Gb SFPs: • FSMF/G/L radio modules with 6 Gb OBSAI RP3 Sales item 472579A

Table 65

DN09142347

Name

Length [m]

FOSH Optical SFP H 850 nm 6 Gb 300 m MM

up to 300 m

For SM - RFM

Notes 6 Gb Multimode SFP 850 nm for OBSAI, two needed per connection, LC PC connector

6 Gb SFPs

Id:0900d805809ed4ff Confidential

125

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

6 Gb SFPs: • FSMF/G/L radio modules with 6 Gb OBSAI RP3 Sales item

Name

Length [m]

For

Notes

472811A

FOSN up to 2 km Optical SFP N 1310 nm 6 Gb 2 km SM

SM - RFM

6 Gb Single mode SFP 1310 nm for OBSAI, two needed per connection, LC PC connector

472580A

FOSI Optical SFP I 1310 nm 6 Gb 15 km SM

SM - RFM

6 Gb Single mode SFP 1310 nm for OBSAI, two needed per connection, LC PC connector

Table 65

up to 15 km

6 Gb SFPs (Cont.)

1 Gb transmission SFPs: • BTS BSC/RNC/MME Sales item 471881A

Name FOSD Flexi Optical Telecom SFP GbE 850 nm MM

Length [m] See Notes

For

Notes

FTIA/B FTJA, FTLB, FIQA/B, FSMF/G/L

1 Gb Multimode SFP 850 nm for transport backhaul, two needed per connection, LC PC connector 550 m on 50/125 μm & 300 m on 62.5/125 μm multimode fiber

Table 66

126

1 Gb transmission SFPs

Id:0900d805809ed4ff Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

1 Gb transmission SFPs: • BTS BSC/RNC/MME Sales item 471880A

Name FOSC Flexi Optical Telecom SFP GbE 1310 nm MM

Length [m] See Notes

For

Notes

FTIA/B FTJA, FTLB, FIQA/B, FSMF/G/L

1 Gb Single mode SFP 1310 nm for transport backhaul, two needed per connection, LC PC connector 550 m on 50/125 μm & 300 m on 62.5/125 μm single mode fiber

Table 66

DN09142347

1 Gb transmission SFPs (Cont.)

Id:0900d805809ed4ff Confidential

127

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.5

DC feeding and extension kit cables Sales item 472806A

472817A

Name FPCA Dual power cable 2m

FPCB DC cable multibeam multi-beam 2m

Length [m] 2m

2m

For

Notes

Release 2 System Module Release 3 RF Module/RRH

2 x multibeam with IP - open end, AWG 10

Release 2 System Module Release 2 RF Module

Multi-beam with IP multi-beam with IP, AWG 10

See Figure 70 FPCA Dual power cable 2 m.

See Figure 71 FPCB DC cable multi-beam multi-beam 2 m. 472823A

472246A

Table 67

128

FPCC DC cable multibeam - open 2m

FPTA 4 m Power cable assembly between RF Module and System Module

2m

4m

Release 2 System Module Release 3 RF Module/RRH

Multi-beam with IP open end, AWG 8

Release 2 System Module Release 2 RF Module

Multi-beam with IP multi-beam with IP, AWG 10

See Figure 72 FPCC DC cable multi-beam open 2 m.

DC feeding and extension kit cables

Id:0900d805809ed819 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Sales item 471226A

472302A

Table 67

Multibeam

Multibeam

Length [m]

For

FSKA Flexi 2 m System Extension Kit (for between System Module and extension System Module with 2 m cables for stack and pole installations)

WCDMA System Module extension System Module

FSKB Flexi 4 m System 4 m power cable kit (for between System Module and extension System Module with 4 m cables for stack and pole installations)

WCDMA System Module extension System Module

Notes •

•

•

•

•

•

Multibeam open end AWG 8 power cable with IP 2 x LC 90° - LC 90° left IP, MM 4 x multimode SFP Multibeam open end AWG 8 power cable with IP 2 x LC 90° - LC 90° left IP, MM 4 x multimode SFP

DC feeding and extension kit cables (Cont.)

Needed only with LOW voltage at 1800 FRM 3x80W

Low voltage in 1800 RFM DC input

3x80W RFM

3x80W RFM

FSMC/D/E

FSMC/D/E

2

AWG x = xx mm

Figure 70

DN09142347

Name

Multibeam connectors cut off

FPCA Dual power cable 2 m

Id:0900d805809ed819 Confidential

129

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Multibeam

AWG 10= 6 mm

2

3x60W RFM

3x80W RFM

FSMC/D/E

FSMC/D/E

Multibeam Multibeam connector cut off

Figure 71

Multibeam

FPCB DC cable multi-beam - multi-beam 2 m

AWG 8=10 mm

Figure 72

3x80W RFM

FSMC/D/E or FSMF/G/L

FSMC/D/E

FSMC/D/E

2

FPCC DC cable multi-beam - open 2 m 3x80W RFM

FSMC/D/E or FSMF/G/L

FSMF/G/L + FPFD

FSMF/G/L + FPFD

2

Copper size 3.3 mm - 25 mm 2 (2.5 - 7 mm) Outer diameter: 6 - 25 mm

Figure 73

130

Standard DC cable open - open (single cable)

Id:0900d805809ed819 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.6

Synchronization cables Sales item

Length [m]

For

Notes

472685A

ESFB Sync ESMA/B/C to FSMF/G/L 12 m

12 m

ESMA/B/C FSMF/G/L

MDR14 HDMI, both with IP

471372A

ESUA Synch cable for Flexi Ultra 12 m

12 m

ESMA/B/C UltraSite EDGE

MDR26 with IP - D15F

472840A

FTSL Sync 2m cable ESMB/C to FSMC/D/E 2 m

ESMA/B/C FSMC/D/E

MDR14 MDR26, both with IP

471371A

ESFA Synch 12 m cable for Flexi 12 m

FSMC/D/E ESMA/B/C

MDR14 MDR26, both with IP

472798A

FSCC Sync 5 m FSMC/D/E to ESMA/B/C 5 m

FSMC/D/E ESMA/B/C

MDR14 MDR26, both with IP

472086A

FSGA Flexi 2 m System sync cable with GPS

FSMC/D/E FSMC/D/E

MDR14 MDR26, both with IP

472576A

FTSG Sync Cable G

2m

FSMC/D/E FSMF/G/L

MDR14 HDMI, both with IP

472799A

FSCB Sync FSMF/G/L to ESMA/B/C

5m

FSMF/G/L ESMA/B/C

HDMI MDR26, both with IP

472808A

FTSK Sync cable FSMF/G/L to FSMD/E

2m

FSMF/G/L FSMD/E

HDMI MDR26, both with IP

Table 68

DN09142347

Name

Flexi Multiradio BTS synchronization cables

Id:0900d805809ed92a Confidential

131

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Sales item

Length [m]

For

Notes

472686A

ESUB Sync cable FSMF/G/L to D15 Ultra 12 m

12 m

FSMF/G/L UltraSite EDGE

HDMI with IP - D15F

472846A

FTSN Flexi sync FSMF/G/L to FSMF/G/L 15 m

15 m

FSMF/G/L FSMF/G/L

HDMI HDMI, both with IP

472509A

FTSF Sync Cable F

2m

FSMF/G/L FSMF/G/L

HDMI HDMI, both with IP

471377A

ESLA Synch 5 m LMU cable 5 m

Table 68

132

Name

MDR26 + RJ45 (with IP) - MDR14 + RJ9 (no IP) + M5 to M6 grounding cable

Flexi Multiradio BTS synchronization cables (Cont.)

Id:0900d805809ed92a Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.7

GPS feeding cables Sales item

Length [m]

For

Notes

472510A

FTSE GPS 30 m cable assembly 30 m

FSMF/G/L GPS

HDMI with IP - IMC262212X (circular 12pole from Deutsch)

472577A

FTSH GPS cable assembly 100 m

FSMF/G/L GPS

HDMI with IP - IMC262212X (circular 12pole from Deutsch)

Table 69

Sales item

100 m

GSP feeding cables for System Module variants FSMF/G/L

Name

Length [m]

For

Notes

471606A

FYHA GPS cable set MDR26 Deutsch

30 m

FSMC/D/E GPS

MDR26 with IP - IMC262212X (circular 12pole from Deutsch)

471653A

FYHB GPS cable set MDR26 Deutsch

100 m

FSMC/D/E GPS

MDR26 with IP - IMC262212X (circular 12pole from Deutsch)

Table 70

DN09142347

Name

GSP feeding cables for System Module variants FSMC/D/E

Id:0900d805809ed92b Confidential

133

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.8

EAC cables Sales item

Length [m]

For

Notes

471408A

FTCR OD cable RJ45 Cat5e 15 m

15 m

Units with EAC (& RJ45 transmisFSEC/FSES sion) cable RJ45 with IP - open end

471717A

FTCS OD cable RJ45 Cat5e 30 m

30 m

Units with EAC (& RJ45 transmisFSEC/FSES sion) cable RJ45 with IP - open end

471718A

FTCT OD cable RJ45 Cat5e 50 m

50 m

Units with EAC (& RJ45 transmisFSEC/FSES sion) cable RJ45 with IP - open end

472839A

FSAH EAC cable HDMI - D37 15 m

15 m

FSMF FSEB

HDMI with IP - D37F

472563A

FSAD Flexi RRH System alarm cable 2.5 m

2.5 m

Units with MDR14 FSEB

MDR14 with IP - D37F

472284A

FSAC Flexi RRH System alarm cable 15 m

15 m

Units with MDR14 FSEB

MDR14 with IP - D37F

472693A

FSAE EAC cable HDMI - RJ45 2 m

2m

FSMF/G/L Units with RJ45 EAC

HDMI RJ45, both with IP

472695A

FSAF EAC cable HDMI - D37 50 m

50 m

FSMF/G/L FSEB

HDMI with IP - D37F

472578A

FTSI EAC Cable

2.5 m

FSMF/G/L FSEB

HDMI with IP - D37F

472836A

FSAI EAC cable MDR36 RJ45 2 m

2m

FSMC/D/E Units with RJ45 EAC

MDR36 RJ45, both with IP

Table 71

134

Name

Flexi Multiradio BTS EAC cables

Id:0900d805809ed980 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Sales item

Length [m]

For

Notes

471628A

FSAA Flexi System alarm cable 15 m

15 m

RF Module FSEB

MDR36 with IP - D37F

472629A

FTSJ EAC cable MDR36 D37 2.5 m

2.5 m

Release 3 RF Module FSEB

MDR36 with IP - D37F

472837A

FSAJ EAC cable D37 RJ45 2.5 m

2.5 m

Units with RJ45 FSEB

RJ45 with IP - D37F

472813A

FSAG EAC cable MDR14 RJ45 2 m

2m

Units with MDR14 Units with RJ45

MDR14 RJ45, both with IP

471464A

EBCA BBU Alarm cable 2 m (used for connecting up to six BBU alarms to ESMB/C)

2m

BBU ESMA/B/C

RJ45 with IP - D9

Table 71

DN09142347

Name

Flexi Multiradio BTS EAC cables (Cont.)

Id:0900d805809ed980 Confidential

135

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

37.9

Miscellaneous cables Sales item

Length [m]

472454A

RDSA RX Diversity sharing kit 2 m

2m

471384A

EQCA Q1 cable 3.1 m (used when Q1 controlled external equipment on site)

3.1 m

471370A

ELCA LMP 50 m cable 50 m (optional outdoor-protected long LMP cable, used at mast top)

472081A

FTNA Iub adapter for NB cabinet

Table 72

136

Name

For

Notes

RF Module RF Module

6 x QMA 7/16 (6 cables in the kit) RJ - RJ Q1 cable

PC - LMP port

RJ(45) RJ(45) LMP cable

Cable + PWC

Flexi Multiradio BTS miscellaneous cables

Id:0900d805809ed982 Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Appendix Casing and cover kits need for Flexi Multiradio units

38 Appendix Casing and cover kits need for Flexi Multiradio units Module

Casing

Kit *)

Casing needed for installation in Floor/Wall Pole

FCIA

FCOA

FMSA/B & IRSA

Power cabinet

ESMA/B/C

Casing optional

EMHA/FMS C

Yes

No

No

Yes, FMSC

No

FSMC/D/E

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

FSMG/L/F

Always with casing

FMCF or FMCA v. 207 (or newer)

N/A

N/A

N/A

N/A

N/A

*) Flexi Mounting Shield 3U Casing (FMSC) + Flexi Mounting Covers for Back and Front (FMCA) = Flexi Module Casing (EMHA)

Table 73

Casing and cover kits need for System Modules

Module

Casing

Kit

Casing needed for installation in

Included in the delivery

Floor/Wall Pole

FCIA

FCOA

FMSA/B *) & IRSA

Power cabinet

DC cable 2M (2xmulti beam)

Multimode fiber 2m

2 SFP (multimode)

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

Yes

Yes

Yes

FRGP 2100 Always with 3x60 W casing

FMCA

N/A

N/A

N/A

N/A

N/A

Yes

Yes

Yes

FRHA 2600

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

Yes

Yes

Yes

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

Yes

Yes

Yes

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

Yes

Yes

Yes

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

Yes

Yes

Yes

Casing optional

EMHA

Yes

No

No

Yes

No

Yes

Yes

Yes

FRGF 2100 3x60 W

3x60 W FRIE 1.7/2.1 3x60 W FRKA 1500 3x60 W FRMA 800EU 3x60 W FXCA 850 3x60 W

Table 74

Casing and cover kits need for Radio Modules

DN09142347

Id:0900d805809d550a Confidential

137

Appendix Casing and cover kits need for Flexi Multiradio units

Module

FXDA 900

Casing

Kit

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Casing needed for installation in

Included in the delivery

Floor/Wall Pole

FCIA

FCOA

FMSA/B *) & IRSA

Power cabinet

DC cable 2M (2xmulti beam)

Multimode fiber 2m

2 SFP (multimode)

Casing optional

EMHA

Yes

No

No

Yes

No

Yes

Yes

Yes

Casing optional

EMHA

Yes

No

No

Yes

No

Yes

Yes

Yes

Casing optional

EMHA

Yes

No

No

Yes

No

Yes

Yes

Yes

3x60 W FXFA/B 1900

Casing optional

EMHA

Yes

No

No

Yes

No

Yes

Yes

Yes

FRGS 2100 Casing optional 3x60 W

EMHA

Yes

No

No

Yes

No

Yes

Yes

Yes

FXCB 850

Casing optional

EMHA

Yes

No

No

Yes

No

No

No

No

Casing optional

EMHA

Yes

No

No

Yes

No

No

No

No

Casing optional

EMHA

Yes

No

No

Yes

No

No

No

No

Casing optional

EMHA

Yes

No

No

Yes

No

No

No

No

EMHA

Yes

No

No

Yes

No

No

No

No

3x80 W

Casing optional

All RRHs (except FRGG)

Sunshield included

N/A

Only pole/wall

N/A

N/A

N/A

N/A

No

No

No

N/A

Only pole/wall

N/A

N/A

N/A

N/A

No

No

No

3x60 W FXDJ 900J 3x60 W FXEA 1800

3x60 W

3x80 W FXDB 900 3x80 W FXEB 1800 3x80 W FXFC 1900 3x80 W FXGT 1900

FRGG RRH Optional sunshield

*) For modules delivered without a casing, use Flexi Mounting Shield 3U Casing (FMSC) (recommended)

Table 74

Casing and cover kits need for Radio Modules (Cont.)

Module

Casing

Kit

Casing needed for installation in Floor/Wall Pole

FCIA

FCOA

FMSA/B & IRSA

Power cabinet

FPDA (24->48 VDC)

Always with casing

FMCB

N/A

N/A

N/A

N/A

N/A

FPMA (BBU)

Always with casing

FMCA

N/A

N/A

N/A

N/A

N/A

Table 75

138

Casing and cover kits need for Power Modules

Id:0900d805809d550a Confidential

DN09142347

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

Module

Casing

Appendix Casing and cover kits need for Flexi Multiradio units

Kit

Casing needed for installation in Floor/Wall Pole

FPRA (rectifier)

Table 75

Always with casing

FMCA

N/A

FCIA N/A

FCOA N/A

FMSA/B & IRSA N/A

Power cabinet N/A

Casing and cover kits need for Power Modules (Cont.) Following tables list the compatibility of EMHA and FMCA with Flexi EDGE System Modules, Flexi Multiradio System Modules and Flexi Power Modules. Air deflector plate has been removed from EMHA (470316A.208) and FMCA (470239A.207) versions. System Module

EMHA 470316A.207

EMHA 470316A.208

(Air deflector plate included)

(Air deflector plate not included)

ESMA 470246A.101 – 106

Compatible

Not compatible

ESMA 470246A.1071)

Compatible

Compatible

ESEA 470330A.101 – 105

Compatible

Not compatible

ESEA 470330A.106 1)

Compatible

Compatible

1)Air

deflector plate is part of ESMA and ESEA delivery.

Table 76

EMHA compatibility with Flexi EDGE System Modules

System Module

FMCA 470239A.206

FMCA 470239A.207

(Air deflector plate included)

(Air deflector plate not included)

FSMF 472181A.10x

Not compatible

Compatible

FSMG 472295A.10x

Not compatible

Compatible

FSML 472424A.10x

Not compatible

Compatible

Table 77

FMCA compatibility with Flexi Multiradio System Modules

Power Module

FMCA 470239A.206

FMCA 470239A.207

(Air deflector plate included)

(Air deflector plate not included)

FPMA 470139A. 204

Compatible

Not compatible

FPMA 470139A.2052)

Compatible

Compatible

FPRA CS7000000.07

Compatible

Not compatible

FPRA CS7000013.02 Table 78

DN09142347

FMCA compatibility with Flexi Power Modules

Id:0900d805809d550a Confidential

139

Appendix Casing and cover kits need for Flexi Multiradio units

Power Module

FPRA CS7000000.082)

Flexi Multiradio Base Station and Flexi Multiradio 10 Base Station Optional Items Description

FMCA 470239A.206

FMCA 470239A.207

(Air deflector plate included)

(Air deflector plate not included)

Compatible

Compatible

FPRA CS7000013.032) 2)Air

deflector plate is part of FPMA and FPRA delivery.

Table 78

140

FMCA compatibility with Flexi Power Modules (Cont.)

Id:0900d805809d550a Confidential

DN09142347