• Author / Uploaded
• suneth_fernando_6

Citation preview

SJ-740 / SJ-740i Install Guide

Read this first. This describes the setup tasks and important conditions about the installation location that must be met in order to enable use of this machine.

CATALOGUE Installation Requirement........................................................................................... 1 Included Items .............................................................................................................. 2 1. Assemble Mechanical Part ................................................................................... 4 1.1 : Assemble the Stand - Mount the Machine . .............................................................. 4 1.2 : Install the Media Feeder and Media Take Up (if any) ............................................. 4 1.3 : Install Cooling Fan............................................................................................................... 5 1.4 : Install Drain Bottle............................................................................................................... 5 1.5 : Install Upper Part of the Printer ..................................................................................... 6 1.6 : Remove Packing Material ................................................................................................. 6 1.7 : Parts Name ............................................................................................................................. 6

2. Turn On the Printer for the First Time Check ................................................. 9 3. Install Media .............................................................................................................. 9 4. Install Printhead and Related Part ...................................................................11 4.1 : Install Printhead ................................................................................................................ 11 4.2 : Fill Ink Cartridges .............................................................................................................. 13 4.3 : Install Damper and Fixator............................................................................................ 13

5. Install USB Driver and PrintConsole................................................................14 6. Fill Ink .........................................................................................................................16

Installation Requirement Install in a quiet, stable location offering good operating conditions. An unsuitable location can cause accident, fire, faulty operation, or breakdown. Install the machine in a location that is level, stable, and able to bear the weight of the machine. The total weight of the machine may reach 400kg or more. Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse. Install in a clean, brightly lit location. Conduct operations in a clean, brightly lit location. Working in a location that is dark or cluttered may lead to an accident, such as becoming caught in the machine as the result of an inadvertent stumble. Position so that the power plug is within immediate reach at all times. This is to enable quick disconnection of the power plug in the event of an emergency. Install the machine next to an electrical outlet. Also, provide enough empty space to allow immediate access to the electrical outlet. Ensure adequate ventilation for the work area. Failing to perform ventilation may result in a health hazard or danger of combustion due to ink fumes. Temperature and Humidity Keep the room temperature between 20-30C, hundity 40-60%. Air conditioner and humidifier may be required. Keep a distance from strong radiation field. The floor must be level. Maintain the specified temperature and humidity even when the machine is not in use. If temperatures are too high or too low, it may cause malfunction. Electrical requirement Electrical requirement writes on a metal tag on the back of the printer. Find it to confirm if your printer supports 220V or 110V. A transformer is needed if your country standard is different. The printer must be well grounded. UPS and voltage stabilizer is highly recommended. Computer requirement Basic requirement: CPU: 2.5 GHz or higher Memory: 2GB or higher Hard Disk: 200GB or higher Operating system: Microsoft Windows XP / Windows 7 Ultimate Edition / Windows 10 Recommendatory requirement: CPU: 3.5 GHz or higher Memory: 4GB or higher Hard Disk: 500GB or higher (NTFS format) Operating system: Microsoft Windows 7 Ultimate Edition NOTICE: Suggest user format your hard disk into 2 partitions (NTFS). The first partition is used for installing OS and other software, the second partition is used to save pictures and work files.

Page 1

Included Items The following items are packed together with the unit. Make sure they are all present and accounted for. Quantit y

Units

1 or 2

pc

1

pc

USB Cable

1

pc

5

Spanner (hexagonal shaped)

1

set

6

Screw driver (cross shaped)

5x150

1

pc

7

Power Cable

8

Screw

0.75mm² 1mm² 1mm²Outside heater * M3x8 M4x12 M6x16

1 1 1 20 8 26

9

Damper

10

Funnel

11

No.

Item Name

Remark

1

EPSON DX5 / DX7 Printhead

2

UltraPrint / PhotoPrint Software

UltraPrint does not include a CD

3

USB Disk & USB Dongle

USB Disk contains driver & manual, Dongle is for PrintConsole & UltraPrint

4

pc pc pc pc

1 or 2

pc

fill ink

4

pc

Ink hard tube

370cm or 510cm

1

pc

12

Ink soft tube

100cm

1

pc

13

Syringe

glass one for cleaning plastics one for manually pump

3

pc

14

ink pipe connector & Seal ring

Connect ink tube and damper

4

pc

15

Media Holder

4-6x25 black screws

2

pc

16

Printhead Flat cable

17

Drain Bottle

18

Fuse

19

6

pc

1

pc

5 10

pc pc

Capping Unit

1 or 2

pc

20

Wiper

1 or 2

pc

21

Fan holder screw

22

Media Reflector *

23

Heating holder screw *

10A 3A

5x30black screws

5x30

4 1

pc

4

pc

* Note : Items in red are optional parts

Page 2

Included Items Page 3

1. Assemble Mechanical Part 1.1 : Assemble the Stand - Mount the Machine

1.2 : Install the Media Feeder and Media Take Up * You may need to install the media reflector and make it faces towards the detector on stand 1. * In some models, media reflector is replaced with a installed infrared detector. * Media take up is optional part.

Page 4

1.3 : Install Cooling Fan

1.4 : Install Drain Bottle * Be sure to insert the drain pipes into the drain bottle afterward.

Page 5

1.5 : Install Upper Part of the Printer Lift the upper part with forklift or 4 men, and fix it onto the stands. * Be sure to insert the jointing rubber into the hole on top of the stands.

1.6 : Remove Packing Material Remove the fixation rubber located on the left side of the carriage. It’s used to fix the carriage during shipping. Remove the packing bags of the dampers.

Page 6

1.7 : Parts Name Pinch Roller

Carriage

Control Panel

Emergency Switch

Media Handle Vacuum Switch Cooling Fan Switch Take Up Switch Main Power Switch

USB Port

Cartridges

Page 7

Carriage Board Printhead Cable

Damper Printhead

Wiper

Capping Station

Capping Unit

Front & Back Heater

Page 8

2. Turn On the Printer for the First Time Check After the stand assembling is completed, plug the power cables and turn on the printer. Remember to turn on both main power switch and the emergency switch. Normal start up action should be : The carriage moves out then goes back to home position, in the mean time, the capping station goes down then goes up slightly leaving the printhead uncapped. This startup check can reduce the risk of a possible short circuit before installing the printhead. Turn off the printer afterward.

3. Install Media Step 1 : Install the media holder and fit on the media tube. Step 2 : Pass the leading edge of the media through the pinch rollers and pull out the media over the platen. (Be sure the media is put straight and taut.) Step 3 : Lower the loading level, then secure the media holder by tightening the securing screws slightly. (Be sure both edges of the media are not covered by the pinch rollers.) Step 4 : Move the media clamps onto both edges of the media. (Be sure only around 5mm of each edge is covered by the media clamp.) Step 5 : Hang down the paper to block the media sensor and reflector. (This can be done manually, or turn on the media feeding motor to rotate the paper tube forward.)

Heavy Roll : Simply put the media tube onto both media rollers, also need to hang down the paper to block the media sensor and reflector. It’s better to put an empty hard paper tube to make paper feeding smooth.

Page 9

Step 1

Step 2

Step 3

Step 4

Step 5

Heavy Roll

Page 10

4. Install Printhead and Related Part 4.1 : Install Printhead Step 1 : Connect flat cables onto the printhead. * Be sure the power is off. * Be sure the text sides of cables are put back to back. (outwards) * Be sure your hand is dry, no ink / liquid gets onto the cables. * Be sure the contact pins are well touched and not bent.

Page 11

(The other side of cables are already connected) Step 2 : Fix the printhead onto the carriage plate by fasten 3 screws.

Page 12

4.2 : Fill Ink Cartridges Use funnel to fill ink into cartridges. Remember to seal them afterwards.

4.3 : Install Damper and Fixator Fix the damper onto the printhead, with gentle strength. * the printhead connector for damper is actually fragile, not as strong as it looks. * Color arrangement should be : C M C M K

K

Y

Y

Fixator

Damper

Page 13

5. Install USB Driver and PrintConsole USB Driver and PrintConsole install program can be found in the USB flash drive. Install the USB driver according to your operation system (32bit / 64bit).

Install the PrintConsole according to your printer model. Then launch the PrintConsole and select the configuration file. : SJ-740, SJ-1260, ES-740

ES-740 with one head ES-740 with two heads SJ-740 / SJ-1260 with one head SJ-740 / SJ-1260 with two head

Note : If you use single head on a two head model, you should still select the PrintConsole for Dual Head Model, but select a different configuration file.

: SJ-740i, SJ-640i, ES-740i

ES-740i SJ-640i SJ-740i

: UV-740, UV-1260

UV-740 / UV-1260 with one head UV-740 / UV-1260 of CMYK UV-740 / UV-1260 of CMYK with White

Page 14

Connect the green USB Dongle. It is required for both PrintConsole and UltraPrint.

Turn on the printer and restart PrintConsole, left bottom corner turns green and says “Printer Connected”. Now the printer is ready to serve.

Page 15

6. Fill Ink Click Settings, select Heads for two heads, select Head1 for single head, then click Fill Ink button.

Page 16

Thank you for choosing SinoColor products. Contact Us Sales Email : [email protected] Support Email : [email protected] Web : www.sanyi-tech.com