WWW.LT1SWAP.COM [ HOME ] [ PCM PROGRAMMING ] [ WIRE HARNESS INFO ] [ VORTEC 8100 ] [ VORTEC 6.0L ] [ '62 I
Views 272 Downloads 2 File size 162KB
WWW.LT1SWAP.COM [ HOME ] [ PCM PROGRAMMING ] [ WIRE HARNESS INFO ] [ VORTEC 8100 ] [ VORTEC 6.0L ] [ '62 IMPALA ] ['67 CHEVY C10] [GM ECM TUNING] [ LINKS ] [ PHOTO GALLERY ] Visit my Facebook page for a lot of New Pictures & Harness Guides - E-Mail: [email protected]
Below are the ECM Connectors for 2008 vortec 5.3L harness. Should be similar for 4.8L 6.2L applications.
BLOCKS HIGHLIGHTED LIKE THIS, ARE WIRES THAT ARE NEEDED, AND GO TO EXTERNAL CONNECTION FOR STAND ALONE I have also highlighted the 6 wires use TRUCK and CAMARO have two pins swapped on gas pedal, D and F
BLOCKS HIGHLIGHTED LIKE THIS, ARE WIRES THAT CAN BE REMOVED FROM PCM CONNECTORS, NOT NEEDED. Note: Removing all of these will result in a non-e EVAP system, then you will not want to remove those components. WIRES THAT ARE NOT HIGHLIGHTED REMAIN UN TOUCHED. THEY WILL GO DIRECTLY FROM ECM TO A PLUG, (SENSOR, SWITCH, DEVICE ETC.) OEM#:13580788 73-Way Female MX123 34566 Series, Color Black
These Pinouts are for GAS engines (EXCEPT LY6)
J1 Connector or X1
Pin
Wire
1
0.35 OG/BK
2
Circuit
Function
1786 Park/Neutral Signal
goes to transmission range switch ground signal
0.5 GY/BK
1694 4WD Low Signal (NQG/NP2)
some harnesses has a pin plug in ecm connector
3
0.5 TN/WH
1695 Axle Switch Signal (NQG/NP2)
some harnesses has a pin plug in ecm connector
4
--
--
Not Used
5
--
--
Not Used
6
--
--
Not Used
7
--
--
Not Used
8
--
--
Not Used
9
0.5 L-BU/WH
10 11 12
6311 Brake Switch Signal
to underhood fuse block P3, wire also goes to TCM, both hook to tcc brake switch at brake pedal, 12v+ key hot, hot
0.5 PU/WH
1668 HO2S High Signal Bank 1 Sensor 2
0.5 TN/WH
1669 HO2S Low Signal Bank 1 Sensor 2
0.35 OG/BK
A/C Refrigerant Pressure Sensor Signal 380 (CJ2/C67) Low Reference (4.8L/5.3L6.0L/6.2L with CJ2/C67) - A/C Refrigerant 5514 Pressure Sensor Pin 1
13
0.35 TN
14
--
--
Not Used
15
--
--
Not Used
16
0.35 PU
17
D-BU/WT
18
0.5 D-BU
19
0.5 PK
20
0.5 RD/WH
21
--
--
Not Used
22
--
--
Not Used
23
0.35 PU
1272 Low Reference - APP Sensor Pin A
X109 C1
24
0.35 D-GN
890 Fuel Tank Pressure Sensor Signal
25
--
--
Not Used
26
--
--
Not Used
27
0.5 TN/BK
2501 High Speed GMLAN Serial Data Bus (-)
28
0.5 TN/BK
2500 High Speed GMLAN Serial Data Bus (+) GOES TO TCM
29
0.35 D-BU
1161 APP Sensor 1 Signal - APP Sensor Pin E X109 C4
30
0.35 BN
31
0.35 TN/BK
32 33
0.35 L-BU 0.35 GY
1589 Fuel Level Sensor Signal - Primary --
High Speed Cooling Fan Relay Control
5985 Accessory Wakeup Serial Data
UNDERHOOD B5
439 Ignition 1 Voltage ECM 12v+ KEY HOT UNDERHOOD P5 Battery Positive Voltage ECM 12v+ BATT 440 HOT UNDERHOOD D3
1271 Low Reference - APP Sensor Pin F Low Reference - Fuel Tank Pressure Sensor Pin A, Fuel Pump Sender 6049 Assembly Pin B
GOES TO TCM
X109 C6
1162 APP Sensor 2 Signal - APP Sensor Pin B X109 C2 2709 5-Volt Reference 1 - Fuel Tank Pressure Sensor Pin C
5-Volt Reference 1 - A/C Refrigerant 2700 Pressure Sensor Pin 2
34
0.35 GY/WH
35
--
36
0.35 TN
37
0.5 TN/BK
38
0.5 TN
39
--
--
Not Used
40
--
--
Not Used
41
0.5 YE
42
--
--
Not Used
43
--
--
Not Used
44
--
--
Not Used
45
--
--
Not Used
46
--
--
Not Used
47
0.5 PK/BK
48
--
49
0.5 TN
50
--
Not Used
1274 5-Volt Reference 1 - APP Sensor Pin C
X109 C3
472 IAT Sensor Signal - MAF Pin D
2760 Low Reference - MAF Pin E (for IAT)
492 MAF Sensor Signal - MAF Pin A
1339 Ignition 1 Voltage ECM 12v+ KEY HOT ADD PIN HERE FOR TACH SIGNAL -- OUTPUT
UNDERHOOD N1
1671 HO2S Low Signal Bank 2 Sensor 2
0.35 D-GN/WH 465 Fuel Pump Relay Control - Primary
UNDERHOOD P4
51
0.35 TN
52
0.5 YE/BK
53
--
--
Not Used
54
--
--
Not Used
55
--
--
Not Used
56
0.35 WH/BK
1164 5-Volt Reference 2 - APP Sensor Pin D
X109 C5
57
0.35 YE/BK
1827 VSS Output to ABS System 128k ???
wire goes to plug at end of transmission harness leg, next to rear o2
58
0.5 D-GN
335 Low Speed Cooling Fan Relay Control
UNDERHOOD A1
59
0.35 YE
5991 Powertrain Relay Coil Control
UNDERHOOD P2 this wire USUALLY power a relay, that inturn powers up all the PNK/BLK wires at the underhood fuse
60
--
61
0.5 WH
62
--
63 64 65
1465 Fuel Pump Relay Control - Secondary
empty on 5.3 no pin plug
625 Starter Enable Relay Control
UNDERHOOD C5
--
Not Used
1310 EVAP Canister Vent Solenoid Control --
Not Used A/C Compressor Clutch Relay Control 0.35 D-GN/WH 459 (CJ2/C67) HO2S Heater Low Control Bank 2 0.5 OG/WH 3223 Sensor 2 HO2S Heater Low Control Bank 1 0.5 GY/WH 3122 Sensor 2
66
--
--
67
--
--
68
0.35 BN/WH
Not Used
UNDERHOOD C3
Not Used MIL Control - "Service Engine Soon" Computer supplies GROUND to turn on 419 light X109 A7
69
0.5 PU
1970 HO2S High Signal Bank 2 Sensor 2
70
0.35 L-BU
1937 Secondary Fuel Level Sensor Signal
0.35 OG/BK
Replicated TOS Signal (without 31 6399 Series without NQF/NQG/NP2)
GOES TO TCM
71
0.5 PU/WH
VSS High Signal - TO SPEED SENSOR ON 821 MANUAL TRANS
72
0.5 L-GN/BK
VSS Low Signal - TO SPEED SENSOR ON 822 MANUAL TRANS
73
3 BK/WH
451 Ground
OEM#:13511426 80-Way Female Receptacle 0.64 2.8 Sealed, Color Gray
These pinouts are for GAS engines (EXCEPT 4.3L v6 and LY6)
J2 Connectoror X2 Pin
Wire
Circuit
1
--
--
2
0.35 PU/WH
Function
Not Used
5-Volt Reference 2 - Crankshaft 6270 Position Sensor Pin C
3
0.35 GY
4
--
5
0.5 BN
6
0.5 YE
7
--
8
0.5 D-GN/WH
428 EVAP Canister Purge Solenoid Control
0.5 GY
Cylinder Shutoff Solenoid Control (3) 5493 (except 4.8L)
0.5 D-BU
Cylinder Shutoff Solenoid Control (1) 5491 (except 4.8L)
9 10
2701 5-Volt Reference 2 - Throttle Body Pin E --
Not Used TAC Motor Control - 2 - Throttle Body 582 Pin A TAC Motor Control - 1 - Throttle Body 581 Pin B --
Not Used
11
0.5 OG
12
0.5 GY/WH
13
0.5 L-GN
Cylinder Shutoff Solenoid Control (4) 5494 (except 4.8L) HO2S Heater Low Control - Bank 1 3113 Sensor 1 HO2S Heater Low Control - Bank 2 3212 Sensor 1
14
0.5 L-GN/BK
Cylinder Shutoff Solenoid Control (2) 5492 (except 4.8L)
15
--
--
Not Used
Camshaft Actuator Solenoid Control 5284 (6.0L/6.2L) Pin 2
16
0.35 PU
17
0.5 D-BU/WH
878 Fuel Injector 8 Control
18
0.5 TN/WH
845 Fuel Injector 5 Control
19
0.5 YE/BK
846 Fuel Injector 6 Control
20
0.5 TN
1744 Fuel Injector 1 Control
21
0.5 YE
410 ECT Sensor Signal - ECT Pin B
22
0.5 TN
2761 Low Reference - ECT Pin A
23
--
--
Not Used
24
--
--
Not Used
25
--
--
Not Used
26
0.8 D-BU
496 KS 1 Signal - KS1 Pin A
27
0.8 GY
1716 KS 1 Signal - KS1 Pin B
28
--
29
0.8 L-BU
1876 KS 2 Signal - KS2 Pin A
30
0.8 GY
2303 KS 2 Signal - KS2 Pin B
31
--
--
32
0.5 GY
23
33
0.5 BN
--
Not Used
Not Used
34
0.35 BK
Generator Field Duty Cycle Signal Oil Level Switch Signal (Early 1174 Production) Low Reference - Engine Oil Pressure 2755 Sensor Pin 1
35
0.35 TN
2752 Low Reference - Throttle Body Pin C
36
--
37
0.5 L-GN/BK
1745 Fuel Injector 2 Control
38
0.5 PK/BK
1746 Fuel Injector 3 Control
39
0.5 L-BU/BK
844 Fuel Injector 4 Control
40
0.5 OG/BK
877 Fuel Injector 7 Control
41
0.35 GY/WH or GY ???
5-Volt Reference 1 - Engine Oil 2705 Pressure Sensor Pin 2
42
--
43
0.35 GY
2704 5-Volt Reference 1 - MAP Sensor Pin C
44
0.35 D-BU
5-Volt Reference 1 - Camshaft Position 6259 Sensor Pin A
45
--
--
Not Used
46
--
--
Not Used
47
--
--
Not Used
48
--
--
Not Used
49
--
--
Not Used
50
0.35 TN/WH
51
--
--
--
Not Used
Not Used
331 Oil Pressure Sensor Signal --
Not Used
Low Reference (6.0L/6.2L) - Camshaft 2199 Position Actuator Sol Valve Pin 1
52
0.35 TN
53
0.35 OG/BK
54
--
--
Not Used
55
--
--
Not Used
56
0.5 TN
1664 HO2S Low Signal - Bank 1 Sensor 1
57
0.5 PU/WH
1665 HO2S High Signal - Bank 1 Sensor 1
58
0.35 L-GN
432 MAP Sensor Signal - MAP Sensor Pin B
59
0.5 PU
1666 HO2S High Signal - Bank 2 Sensor 1
60
0.5 TN
1667 H02S Low Signal - Bank 2 Sensor 1
61
0.5 BN
25
Charge Indicator Signal
62
--
--
Not Used
63
0.35 PU
64
469 Low Reference - MAP Sensor Pin A
486 TP Sensor 2 Signal - Throttle Body Pin F
CMP Sensor Signal - Camshaft Position 0.35 D-BU/WH 6265 Sensor Pin C
65
0.35 D-GN
66
0.35 BN
485 TP Sensor 1 Signal - Throttle Body Pin D Low Reference - Camshaft Position 6266 Sensor Pin B
67
--
--
Not Used
68
0.35 WH/BK
CKP Sensor Signal - Crankshaft Position 6271 Sensor Pin A
69
0.35 GY/BK
Low Reference - Crankshaft Position 6272 Sensor Pin B
70
0.5 PU
2121 IC 1 Control
71
0.5 PU/WH
2128 IC 8 Control
72
0.5 OG
2127 IC 7 Control
73
0.5 OG/WH
2122 IC 2 Control
74
0.5 L-BU/WH
2126 IC 6 Control
75
0.5 D-GN
2125 IC 5 Control
0.5 D-GN/WH 2124 IC 4 Control
76 77
0.5 L-BU
78
0.5 BN
79
0.5 BN/WH
80
--
2123 IC 3 Control Low Reference - Coil Connector Pin E 2129 Odd Bank Low Reference - Coil Connector Pin E 2130 Even Bank --
Not Used