How to do a Compression Test Page 1 of 3 http://geocities.com/dsmgrrrl/FAQs/compression.htm Go DEC FEB 2007 2009
Views 120 Downloads 2 File size 346KB
How to do a Compression Test
Page 1 of 3
http://geocities.com/dsmgrrrl/FAQs/compression.htm
Go
DEC
FEB
2007
2009
MAR Close
4
23 captures 21 Jun 00 - 24 Oct 09
2010
Help
How to do a Compression Test A compression test is an easy way to determine the internal health of your engine. You can pay a dealership $50 to do it for you, or you can do it yourself in about 10-15 minutes. Here's how... You will need: compression gauge 13/16" spark plug socket
You can get one of these for between $15 and $50 almost anywhere you can get auto supplies, including Canadian Tire, Pep Boys, and even WalMart. You don't need a particularly good or expensive one just to make sure you're in spec. Obviously, and a socket wrench, to take out the spark plugs.
Optional, but recommended: 4 new NGK BPR6ES In case any of the plugs are fouled. The NGK are the most frequently recommended spark plugs plugs on the Talon Digest by Club DSM members, so who am I to argue? plug gapping tool If you're not replacing your plugs, and even if you are, you might as well make sure they're properly gapped. oil and a funnel In case you need to do the wet test.
How To: 1. Before you begin, make sure the battery is fully charged. Take it for a good hard drive. 5 minutes of idling won’t cut it. 2. Pull the MPI (MultiPort Injection) fuse on the positive terminal of your battery. This cuts power to the injectors so they don’t spray gas all over the place.
3. Unplug the coil connector, it’s on the right side, at the back of the block. You could get a nasty shock if you don’t.
4. Remove all 4 plugs and examine them carefully for signs of a problem. If your valve seals are bad in any cylinder, the plug will be fouled to some degree. Signs of oil on the plugs could indicate a ring problem.
http://web.archive.org/web/20090204121339/http://geocities.com/dsmgrrrl/FAQs/compres... 3/27/2013
How to do a Compression Test
Page 2 of 3
5. Screw the compression gauge into the plug hole 6. Press the gas pedal to the floor to open the throttle plate, and keep it at WOT (wide open throttle) for as long as you’re cranking (if you didn’t pull the MPI fuse, there would be a bit of a mess, now). 7. Turn the ignition to the ON position, and hold it there for a count of four revolutions (do not turn the key on-and-off four times). On each rotation, the gauge needle will jump slightly less than the previous one. Update: It may take more than 4 revolutions to get a stable reading; crank for up to 10 seconds or until the needle stabilizes, whichever comes first. Note: If your battery is weak, the engine will turn over slower and give you lower readings. 8. The last number the gauge jumps to is the compression for that cylinder. 9. Repeat for each cylinder.
Compression specifications => 14 psi maximum difference between cylinders
1G (90-94) T/E/L
1.8L NT engine
2.0L NT engine
2.0L Turbo engine
Compression ratio Standard compression Service limit
9.0:1 185 psi 131 psi
9.0:1 192 psi 145 psi
7.8:1 164 psi 121 psi
2G (95-99) T/E
2.0L NT 420A engine
2.0L 4G63 Turbo engine
2.4L NT Spyder engine
Compression ratio Standard compression Service limit
9.8:1 170-225 psi 100 psi
8.5:1 178 psi 133 psi
9.5:1 192 psi 146 psi
Galant (89-93)
SOHC 8v engine
SOHC 16v engine
Compression ratio Standard compression Service limit
8.5:1 178 psi 125 psi
9.5:1 185 psi 139 psi
Galant (89-93)
DOHC pre-91 NT engine
DOHC 92+ NT engine DOHC Turbo engine
Compression ratio
9.0:1
9.8:1
7.8:1
http://web.archive.org/web/20090204121339/http://geocities.com/dsmgrrrl/FAQs/compres... 3/27/2013
How to do a Compression Test
Standard compression Service limit
192 psi 137 psi
Page 3 of 3
220 psi 159 psi
164 psi 114 psi
10. In this picture you might not be able to make out the number ... but ... cylinder 2 is losing compression big-time!
All a "wet test" entails is a bit of oil in the low cylinder... 11. Add one capful (1-2 tablespoons) of oil to the cylinder with low compression. 12. Let it sit for a minute to allow the oil to flow down and coat the sides of the cylinder and piston. If there are any gaps in the rings, the oil will seal them for the next few minutes.
13. Crank the engine for 4 revs, remembering to floor the throttle. 14. If the reading improved significantly (more than 30 psi), your rings are probably worn. 15. If there is little or no improvement, take it to a garage that can perform a leak-down test to determine where the compression is escaping (intake, exhaust, crankcase, gasket, etc.). 16. Replace the plugs, preferably in the same cylinders they came out of. You may want to clean or re-gap them first, or put in new ones. A dab of anti-seize on the threads would be a good idea. 17. Remember to put the MPI fuse and coil connector back. You’re not going anywhere without them!
Copyright © 2000-2004 by Marta Cepek Images or text from this website may not be reproduced without the author's written permission (emails to [email protected] will be automatically deleted. Replace "spam" with "marta"). Pictures are of a stock 1G 2.0L Turbo engine. Hands provided by Benoit Labossiere of Camo Tuning, Montreal, Quebec. 1G DSM compression specifications from Haynes Manual. All other compression specs out of the Service Manuals (Vineet Singh's DSM Backup CD).
http://web.archive.org/web/20090204121339/http://geocities.com/dsmgrrrl/FAQs/compres... 3/27/2013